Specifications

E. Disable Feature
The “Disable” input can be connected to a switch for remotely disabling/turning off the strobe light and the device con-
trolled by the auxiliary contacts (camera, etc.). Note: The disable feature on the E-1600A-BLT2-EWP is factory pre-
wired to the “Info” push button. This prevents the strobe from activating when the “Info” push button is pressed.
F. Switched 12V DC Output
The switched 12V DC output is a low current, 12-15VDC output that is turned on only while the trigger input is closed
or ring/loop detect relay is activated. This switched power output is ideal for triggering the included strobe light or pro-
viding 12-15V DC power to any device that draws less than 400mAmps. The positive side is available on the green
wire, and the negative side is on the black wire. Once all the line and load connections have been made, plug in the
115 V AC wall adapter, and replace the cover.
G Trigger Input
The trigger input is available on the two white wires. The Strobe Light, Auxiliary relay contact and the switched 12 VDC
output will be activated for the duration of the contact closure across the two white wires.
P
P
r
r
o
o
g
g
r
r
a
a
m
m
m
m
i
i
n
n
g
g
t
t
h
h
e
e
S
S
L
L
-
-
2
2
S
S
t
t
r
r
o
o
b
b
e
e
/
/
B
B
e
e
a
a
c
c
o
o
n
n
Select the Feature: Momentarily touch the Green (Control) wire to the Black (-) wire 1 to 10 times to select which feature to pro-
gram (see Programming Features List, section C). The strobe should momentarily flash each time the Green (Control) wire has
touched the Black (-) wire.
Features 1-3 & 6-10: After selecting Programming Features 1-3 or 6-10, wait 3 seconds and the strobe should flash 2 times indi-
cating that feature has been programmed. You can now exit programming or move on to programming the Beacon or Strobe bright-
ness settings.
Setting Strobe Brightness (factory set to 6/Brightest): After selecting Programming Feature 4 (Strobe Brightness), wait 3 seconds
and the strobe should begin flashing in the preprogrammed flash pattern. Touch and hold the Green (Control) wire to the Black (-)
wire. The SL-2 will begin flashing the strobe cycling through 6 different brightness settings from lowest to highest. When the SL-2
flashes at the desired brightness level immediately remove the Green wire from the Black. The SL-2 should flash twice indicating
the selected brightness level has been set.
Setting Beacon Brightness (Factory set to 6/Brightest): After selecting Programming Feature 5 (Beacon Brightness), wait 3 sec-
onds and the beacon will light at its preprogrammed beacon brightness setting. Touch and hold the Green (Control) wire to the Black
(-) wire. The SL-2 will begin stepping through 6 different beacon brightness settings from lowest to highest. When the SL-2 lights at
the desired beacon brightness level immediately remove the Green wire from the Black. The SL-2 should flash twice indicating the
selected brightness level has been set.
Exiting Programming: To exit programming simply wait 20 seconds from the last programming command and the unit will flash 3
times. This indicates the SL-2 has exited the programming mode and is now in the Run mode. Note: To eliminate waiting 20 sec-
onds, you can also exit programming after the last programming command by touching and holding the Green (Control) wire to the
Black (-) for 3 seconds. The strobe will flash 3 times indicating the unit has exited the programming mode and is now in the Run
mode.
The SL-2 can be user programmed as a Beacon only, Strobe only or Beacon/Strobe. The brightness setting can be pro-
grammed separately for the Strobe or Beacon and one of 4 different Flash Patterns can be programmed for the Strobe (See
Strobe Flash Patterns, section D). Note: The SL-2 is factory default programmed as a steady on beacon with a single flash
strobe when activated. The beacon and strobe are set to their brightest settings. All programming should be done prior to
connecting to the BLK-4 control module.
A. Accessing the Programming Mode
(Optional, the SL-2 is factory programmed to the Beacon/Strobe Mode and brightest Beacon/Strobe settings).
Step 1. Apply 10-15 VDC power to the Red (+) and Black (-) wires.
Step 2.
Touch and hold the Green (Control) wire to the Black (-) wire for 3 seconds. The strobe should flash twice.
You are now in Programming mode. Note: Once in the programming mode, if a programming command
has not been entered for 20 seconds the strobe will flash 3 times indicating the unit has exited program-
ming and returned to the Run Mode.
B. Programming Desired Features (after accessing Programming Mode above)
6