Specifications
LED3
LED1 LED2
LED4
LED5
LED6
LED7
C
CCCC
C C
J11-
1
2
3
J10-
12
3
J9-
1
2
3
J8-
1
2
3
J7-
1
2
3
1 2 3
on
on
4 5
VIKING
©
MODEL C-2000B
VIKING
ELECTRONICS
HUDSON, WI 54016
ADVANCED DOOR/GATE AND
ENTRY PHONE CONTROLLER
1 2 3 4 5 6 7
89
10 1 1 12 13 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
PWR 13.8 VAC
EARTH GND
ENTRY PHONE 1
DOOR STRIKE 1
ENTRY PHONE 2
DOOR STRIKE 2
ENTRY PHONE 3
DOOR STRIKE 3
ENTRY PHONE 4
DOOR STRIKE 4
DOORBELL SWITCH /
AUX. INPUT
AUX. CONTACT
OUTPUT
PHONE LINE
INPUT
LINE OUT
TO PHONES
ANALOG STATION
INPUT
1
2
ON
5.0”
3.63”
5.0”
3.63”
** Gel-Filled
Butt Connectors
or
* C.O. Line
or Analog
PABX/KSU
Station
Ring
Terminal
(included)
*** Earth
Ground
(optional)
Red (Ring)
Green (Tip)
or
SINGLE ENTRY PHONE
CONTROLLER
VIKING
©
MODEL C-200
P
W
R
1
3
.8
V
A
C
A
U
X
R
E
L
A
Y
C
O
N
T
A
C
T
S
12345 89
10
EARTH
GND
PHONE LINE
INPUT
LINE OUT
TO PHONES
67
TO ENTRY
PHONE
VIKING
ELECTRONICS
HUDSON, WI 54016
EARTH
GND
C.O. LINE
INPUT
OUT TO
PHONES
ENTRY
PHONE
N.O. COM N.C.
AUX CONTACTS
ON
1 2 3
11 12
AUX POWER
OUTPUT
AUX POWER
OUTPUT
RING COUNT
RELAY MODE
DOORBELL MODE
Optional C-2000B Advanced Door
Entry Controller (not included)
Optional C-200 or C-250 Single Entry
Phone Controller (not included)
Rear View of
the E-30
*** Note: To increase surge protection, loosen the PCB mounting screw labeled (as shown above) and fasten a wire with spade terminal (included)
from the mounting screw to Earth Ground (grounding rod, water pipe, etc.)
** Note: The gel-filled (water-tight) butt connectors are designed for insulation displacement on 19-26 gauge wire with a maximum insulation of 0.082
inches. Cut off bare wire ends prior to terminating.
* Note: When installing a line powered phone on a low voltage and/or low loop current phone system extension, a TBB-1B Talk Battery Booster may be
required, see DOD# 632.
B. Wiring the E-30 Phone Board
4
P
P
r
r
o
o
g
g
r
r
a
a
m
m
m
m
i
i
n
n
g
g
Step 1. Move DIP switch 2 to the ON position (sets unit to answer incoming calls - see section F).
Step 2. From a Touch Tone phone call the line attached to the E-30.
Step 3. When the E-30 answers, enter the 6-digit security code (factory set to 845464 - see section C). A double beep
should then be heard indicating you have entered the programming mode.
2. Without the Security Code
A. Accessing the Programming Mode
1. Using the Security Code
Step 1. Move DIP switch 2 to the ON position (sets unit to answer incoming calls - see section F).
Step 2. Move DIP switch 3 to OFF (incoming calls enter the programming mode without security code - see section F).
Step 3. From a Touch Tone phone call the line attached to the E-30.
Step 4. When the E-30 answers, a double beep will be heard and you will automatically enter the programming mode.
Step 5. When finished programming, move DIP switch 3 back to the ON position (see section F).
Note: If a valid memory position is entered, a double beep will be heard, four beeps indicate an error.
?
Need More Information on the DLE-200B?
Call (715) 386-4345 and select 605.
The E-30 phone can be programmed from any Touch Tone phone using a C.O. line, analog PABX/KSU station, or a
DLE-200B Line Simulator.
B. Quick Programming Features
First speed dial number ...........................................................................................
Second speed dial number ......................................................................................
Third speed dial number ..........................................................................................
Fourth speed dial number ........................................................................................
Fifth speed dial number ...........................................................................................
To add a
, at any point in the dialing string ...............................................................
To add a # at any point in the dialing string ...............................................................
To add a four second pause at any point in the dialing string ....................................
Toggle between Touch Tone and Pulse dialing .........................................................
Miscellaneous options (factory set to 000210) .........................................................
Timing/Dialing options (factory set to 234111) .........................................................
Change security code (factory set to 845464) .........................................................
Exit programming and disconnect ...........................................................................
Reset all programming to factory default settings ....................................................
0-20 digits
0-20 digits
0-20 digits
0-20 digits
0-20 digits
,,
,
#
,7
,6
6 digits (0-9)
6 digits (0-9)
6 digits (0-9)
#7
###
#00
#01
#02
#03
#04
#17
#18
#19
Enter Digits
then
then
then
then
then
then
then
then
- then -
Enter Memory Location