Specifications

ManualsBrandsViking ManualsHome building and DecorE-40

Note: Up to 20 digits can be stored in each dial position. Special features such as one and four second pauses, and

touch tone

and # count as a single digit.

The speed dial number stored in location #00 is the first outside number that will be dialed if the door phone goes off

hook and the house phone does not answer within the ring count set by location #44. Additional speed dial numbers

will be dialed if there is no answer or a busy at the first number. Each number is called only once. If all numbers are

called without an answer, the C-250 will generate a CPC signal and then a busy signal will be sent to the door phone.

To clear a speed dial number position, simply enter a # and the location number (00 to 04), without any preceding num-

bers. If no numbers are programmed, the C-250 will only call the house phone.

C. Speed Dial Numbers (Memory Locations #00 to #04)

First phone number ...........................................................................................................................

Second phone number .....................................................................................................................

Third phone number ..........................................................................................................................

Fourth phone number ........................................................................................................................

Fifth phone number ............................................................................................................................

To clear any speed dial number ...............................................................................................................

Door Strike Activation Time ...................................................................

Door Strike Command ..........................................................................

Maximum Call Time ....................................................

Maximum Ring Time .......................................................................

Ring House Phone Count .........................................................

Incoming Ring Count ............................................................................

Security Code ..................................................................................................................

Keyless Entry Mode ........................................................................................

“

QQQ” command for immediate call forwarding ...............................................

Comcast Mode (see Operation section F) .....................................................

To add a “

Q“ at any point in the dialing string or door strike code ..........................................................................................

To add a “#“ at any point in the dialing string or door strike code ...........................................................................................

To disable “No CO” mode (factory setting) ............................................................................................................................

To enable “No CO” mode .......................................................................................................................................................

To disable “Doorbell” mode (factory setting) ..........................................................................................................................

To enable “Doorbell” mode ....................................................................................................................................................

To select a double burst ring pattern (factory setting) ............................................................................................................

To select a single ring pattern ................................................................................................................................................

To actuate the door strike relay ..............................................................................................................................................

To add a four second pause at any point in the dialing string ................................................................................................

To add a one second pause at any point in the dialing string ................................................................................................

Ignore touch tones for programming entry phone ..................................................................................................................

To reset all programming to factory default settings .............................................................................................................

Exit programming ..................................................................................................................................................................

The following commands are used during normal operation:

Enable Immediate Call Forward Mode .................................................................................................................................

Disable Immediate Call Forward Mode (factory setting) ........................................................................................................

(1 to 20 digits)

(no digits)

(00 to 99 sec, 00 = .5 sec, factory 5 sec)

(1 or 2 digits, blank is disable, factory 6)

(1 to 9 mins, 0 = 30 sec, blank is disable, factory 3 min)

(00 to 59 secs, 00 is disable, factory 30 sec)

(1 to 9, 0 = immediate call forwarding, factory 4)

(01 to 99, 00 disables answer, factory 10)

(6 digits, factory 845464)

(factory: 0 = disabled, 1 = enabled)

(factory: 0 = enabled, 1 = disabled)

(factory: 0 = disabled, 1 = enabled)

B. Quick Programming Features

Enter Digits +

Memory

Location

#00

#01

#02

#03

#04

#00 to #04

#40

#41

#42

#43

#44

#45

#47

#50

#51

#52

##1

###

##7

QQQ

###

Set DIP switch 3 on the front of the C-250 to the ON position. Come off hook with the house phone and 2 beeps

will be heard signaling that the C-250 is in the programming Mode. When finished programming, hang up the phone

and set DIP Switch 3 to the OFF position.

1. Local Programming

Set DIP switch 1 on the front of the C-250 to the ON position. Call into the unit from a remote touch tone phone.

After the incoming ring count is up (factory set to 10), the C-250 will answer the line and beep 1 time. Enter Q fol-

lowed by the 6-digit security code (factory set to 845464). Two beeps will be heard signaling that the C-250 is in the

programming mode.

2. Remote Programming with the Security Code

Set DIP switches 1 and 3 on the front of the C-250 to the ON position. Call into the unit from a remote touch tone

phone. After one ring, the C-250 will answer the line and beep 2 times signaling that the C-250 is in the program-

ming mode. When finished programming, hang up the phone and set DIP Switch 3 to the OFF position.

3. Remote Programming without the Security Code