Specifications

VIKING©
VIKING
ELECTRONICS
HUDSON,
WI
54016
ADVANCED 2 DOOR ENTRY PHONE
CONTROLLER WITH CALL FORWARDING
POWER 13.8V AC
MODEL C-500
PHONE LINE
INPUT
LINE OUT
TO PHONES
1234
ENTRY
PHONE 1
56 789
DOOR STRIKE 1
N.C.
N.O. COM
ENTRY
PHONE 2
13 14
SLP
CONTROL
18
+
19
TRIGGER
INPUT 1
10 11 12
TRIGGER
INPUT 2
15 16 17
DOOR STRIKE 2
N.C.
N.O. COM
LED3
LED1 LED2
LED4
LED5
LED6
LED7
C
CCCC
C C
J11-
1
2
3
J10-
12
3
J9-
1
2
3
J8-
1
2
3
J7-
1
2
3
1 2 3
on
on
4 5
VIKING
©
MODEL C-2000B
VIKING
ELECTRONICS
HUDSON, WI 54016
ADVANCED DOOR/GATE AND
ENTRY PHONE CONTROLLER
1 2 3 4 5 6 7
89
10 11 12 13 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
PWR 13.8 VAC
EARTH GND ENTRY PHONE 1 DOOR STRIKE 1 ENTRY PHONE 2 DOOR STRIKE 2 ENTRY PHONE 3 DOOR STRIKE 3 ENTRY PHONE 4 DOOR STRIKE 4 DOORBELL SWITCH / AUX. INPUT AUX. CONTACT OUTPUT PHONE LINE INPUT LINE OUT TO PHONES
ANALOG STATION INPUT
VIKING©
DLE-200B
RES
RINGDOWN
BUSY
1
2
VIKING ©
Programmable
Tone Dialer
MODEL: K-1900-5
Quick Programming Guide
1. Call the phone connected to the dialer.
2. Answer phone. Enter
* & security code.
(Factory set to 845464) Write your
security code below:
3. Enter your spped dial number & #00.
Note: For additional programming see
K-1900-5 Technical Practice.
Viking Electronics, Inc.
Hudson, WI 54016
LINE IN PHONE
Viking C-2000B 1-4 Entry Phone
Controller (not included)
*** Optional Viking
K-1900-5 Dialer or
K-1900-30 Multi-
Number Dialer
(not included)
**** C.O. Line or Analog
PABX/KSU Station
(programmed for ringdown)
Viking DLE-200B
Two Way Ringdown
Circuit (not included)
To dedicated phone, unused trunk/
line input of a phone system, or
Viking C-1000B Doorbox Controller
Viking C-200 or C-250 Single Entry,
or C-500 1-2 Entry Phone
Controller (not included)
To C.O. Line or
PABX/KSU station
Red
(Ring)
Green
(Tip)
** Earth
Ground
(optional)
(Ring
connector
included)
Back View of the
E-50 Circuit Board
Mounting Plate
* 3-Wire Gel-Filled
Butt Connectors
(included) E-50
phone board is not
polarity sensitive
-or-
*** Note: Talk battery must be a minimum of 28V DC when using the speaker phone with a Viking K-1900-5 Dialer (DOD# 317) or K-1900-30 Multi-Number Dialer (DOD# 300).
** Note: To increase surge protection, loosen the PCB mounting screw labeled (as shown above) and fasten a wire with ring terminal (included) from the mount-
ing screw to Earth Ground (grounding rod, water pipe, etc.) After fastening ring terminal to PCB mounting screw, bend terminal up to avoid interference with single
gang box.
* Note: The gel-filled (water-tight) butt connectors (3M Scotchlok UR2) are designed for insulation displacement on 19-26 gauge wire with a maximum insulation of
0.082 inches. Do not strip wires prior to terminating.
**** Note: When installing a line powered phone on a low voltage and/or low loop current phone system extension, a Viking TBB-1B Talk Battery Booster may
be required, see DOD# 632.
E. Wiring the E-50 Phone Board
IMPORTANT: Electronic devices are susceptible to lightning and power station
electrical surges from both the AC outlet and the telephone line. It is recommended
that a surge protector be installed to protect against such surges.
!
(5) 3-Wire Gel-Filled
Butt Connectors
(included)
"Old Work" Rough-In Box
(Allied Molded 9331 box
shown, not included)
Circuit Board
Mounting Plate
(included)
1/4" Thick Foam
Faceplate Gasket
(included)
Facplate
(included)
Green
Red
(2) 6-32 x 1.25" Long
5/64" Hexdrive Flathead
Screws (included)
4.875"
3.125"
(4) Optional Dry
Wall Screws
(not included)
Optional
Mounting Ears
Optional Wing
Brackets
*2.25"
Deep
Min.
Optional VE-3x5 Surface Mount
Box with Black Satin Powder Paint
Finish (not included) WARNING: Do
NOT use a wet location box.
1.8"
3.17"
4.92"
-OR-
Conduit Knockout
Condensation
Drain Hole
Wires from
Phone Board
Wires from
Camera
Red
Black
Yellow
CAT5E
Cable
2.00"
Wide
Min.
W/BL
Blue
Orange
W/O
Green
W/G
2.84"
Tall Min.
** LED
Light Pipe
(included)
C. Surface Mounting
D. Mounting the Faceplate
A Viking model VE-3x5 can be used to surface mount an E-50 to a wall or post. Recommended mounting height to bot-
tom of VE-3x5 is 50” - 54”. Drill a small wire exit hole in wall. Pull wire through and seal hole around wire with putty or
caulking. Route wire into the VE-3x5 box, securely screw it to wall or post and seal hole in box around wire with putty
or caulking. Note: Conduit may also be used when surface mounting wire, but should not enter through the top of the
VE-3x5. When routing wiring from above, a drip loop is required. WARNING: Do NOT use a typical “wet location box”
as not all styles seal properly with the E-50 faceplate.
After the Rough-In box or VE-3x5 is securely mounted, caulking between the box and rough opening is completed (if
required), wires are connected, and camera is tilted and rotated to the desired position (as shown in section G). Remove
paper liner from face plate gasket, while firmly holding the LED light pipe in the faceplate, carefully slide the faceplate gas-
ket over the back of the light pipe and press gasket to the back of the faceplate. Push the 1-1/4" 6-32 screws through face-
plate holes and small holes in gasket, the faceplate gasket should retain the screws. Position the circuit board mounting plate
over screws. Align screws with single gang box bosses and tighten face plate until gasket is fully collapsed and the push but-
ton is protruding through the clearance hole in the face plate. Included 1/4" thick gasket will provide an adequate seal for
most siding surfaces; however for rough surfaces (ie: brick, stucco, etc.) additional caulking may be required.
4
* CAUTION: Excessive wire length and/or using a
rough-in box with inadequate depth can apply force
to the circuit board causing physical damage.
** Important: Push LED light pipe into faceplate hole, then place faceplate
upside down on a clean flat surface and push down on back side of plate
until light pipe is fully seated and straight. WARNING: Inserting the light pipe
more than one time can cause a loose fit.