Product manual

PUSH FOR
VIKING ©
HELP
MODEL E-1600A-TP-IP EWP
EMERGENCY
PHONE
CONNECTED
CALL
"Call Connected" LED
7.750
4.00
2.75
9.50
2.75
Minimum Cutout
10.250
0.875
11.75
5.125
Typ
0.75
4.50
2.125
0.75
5.125
Push for "Help" Button ("Info" Button
available on model E-1600-TP2-IP-EWP)
Marine grade 316 stainless steel faceplate
and push button switch (sealed per IP67)
Grade 2 Braille Label
(6) 0.250 diameter counter sunk 82° x 0.410
diameter holes for flathead #10 x 24
tamper-proof screws (not included)
Gray (N.C.)
Blue (COM.)
Yellow (N.O.)
2 Amp Relay Output Contacts
(to control beacon / strobe light)
E-1600-55-IP
Optional Enhanced Weather Protection (EWP) Available*
The E-1600-55A-IP is a universal emergency phone kit for installing be-
hind elevator panels, or an installation requiring a custom panel. The fin-
ished panel should provide: (4) studs (#6 diameter minimum) for
mounting plate, audio holes for speaker and microphone, a momentary
SPST push button switch and a 0.25” diameter mounting hole for the
LED. Alternatively, the LED can be cut off and the wires connected to a
integral switch with LED (often found in elevators).
Black
Black
Clear Spacer Red 5mm Retaining
Lens Round LED Ring
(4) Countersunk holes for mounting the dust cover
2.0
Diameter
2.25
3.77
4.50
5.0
5.0
4.50
1.76
3.625
Typ.
0.25 Typ.
(4) 0.25 diameter clearance holes for mounting
the unit to the back side of a finished panel.
0.25
Diameter
(4) 6-32 x 3/4"
stainless steel
flat head, 5/64"
hexdrive, screws
(included) for
fastening dust cover
Dust Cover: Install prior
to fastening faceplate
to finished panel.
Red "Call Connected" LED with
included mounting hardware
(requires a 0.25" diameter hole)
Connect to momentary push button switch
with contact rating of 50VDC/100mA min
304 stainless steel speaker and
microphone protection screens
*
*
*
Note: Additional wire length may be added if required.
1/16" thick foam gasket (included) for accoustically sealing mic and speaker
to back of finished panel. Remove backing and adhere gasket to front panel of
the E-1600-55-IP, centering over speaker and microphone holes (as shown).
Red (LED
anode)
Black (LED
cathode)
(4) 0.25 diameter
holes (not used)
Note: If you do not want to use the LED,
tuck it inside the unit. Do NOT cut it off.
Gray (N.C.)
Blue (COM.)
Yellow (N.O.)
2 Amp Relay
Output Contacts
4.0
2.1
*Optional Enhanced Weather Protection (EWP): The op-
tional EWP products feature foam rubber gaskets and boots,
sealed connections, gel-filled butt connectors, as well as ure-
thane or thermal plastic potted circuit boards. See DOD# 859.
Shipping Weight: .73 kg (1.6 lb)
Connections: (1) RJ45 10/100 Base-T, (5) gel-filled butt con-
nectors
Material: 0.062” thick (16 gauge) zinc plated steel
E-1600-TP-IP-EWP / E-1600-TP2-IP-EWP
Dimensions: 241mm x 299mm x 51mm (9.5”
x11.75” x2”)
Shipping Weight: 2.9 kg (6.4 lbs)
Mounting: Flush mount to Talk-A-Phone ETP
towers, wall mounts, boxes and pedestals
Material: .105” (12 gauge) brushed Marine
grade 316 stainless steel
Connections: (1) RJ45 10/100 Base-T, color-
coded wires with gel-filled butt connectors
Enhanced Weather Protection (EWP): EWP
products feature foam rubber gaskets and boots,
sealed connections, gel-filled butt connectors, as
well as urethane or thermal plastic potted circuit
boards. See DOD# 859.
9