Product manual

8
E-1600-50-IP / E-1600-52-IP
E-1600-53-IP
2.20
2.40
Clear Spacer Red Retaining
Lens LED Ring
PUSH FOR
VIKING©
HELP
BL-1 grade 2 black
Braille label included
.785.47
.50
1.0
(2) 0.10 diameter
mounting holes
Mic Hole
Panel
0.827
(4) 0.335 x 0.177 mounting
slots for #4 or #6 studs
-or-
RedBlack
Black
Black
Red
Red
2.60
2.10
2.60
2.10
Speaker
(included)
Screen (included)
2.37
Cone
Dia.
EWP version
is connected and
encapsulated
Red (LED anode)
Black (LED cathode)
**Connect to "INFO" button
(E-1600-52-IP only, requires a
0.75" diameter mounting hole)
**Connect to "PUSH FOR HELP"
or "HELP" button (requires a
0.75" diameter mounting hole)
Red call connected LED with mounting hardware
(requires a 0.250" diameter mounting hole).
** Note: When using the included push button switches, cut off
the forked portion of the spade lugs and fasten screws to the
barrel portion of the spade lugs.
0.60 (0.80 EWP)
maximum
(2) 0.156 diameter
mounting holes
0.15
(0.19
EWP)
3.50
(3.58
EWP)
3.20
2.0
(2.04 EWP)
0.63
(0.67
EWP)
1.5
2.63
(2.71 EWP)
Mylar Speaker Dimensions
Speaker Gasket
(EWP only)
Standard Mic Mounting Boot: Glue
or screw directly behind 0.04” - 0.125”
diameter hole in panel.
EWP Mic Mounting Boot: Glue
to the back of your panel at an
upward angle (shown left) behind
a 0.10” - 0.25” diameter hole.
Note: Mic holes should be near the
bottom of the boot to allow for drainage.
Gray (N.C.)
Blue (COM)
Yellow (N.O.)
Relay Output
Contacts
Side View
Note: This is a 1600-IP
parts kit without chassis.
Shipping Weight: .45
kg (1 lb)
Connections: Gel-filled
butt connectors
*Optional Enhanced
Weather Protection
(EWP): The optional
EWP products feature
foam rubber gaskets and
boots, sealed connec-
tions, gel-filled butt con-
nectors, as well as
urethane or thermal plas-
tic potted circuit boards.
See DOD# 859.
Important: If installing
the EWP version out-
doors, apply a non-corro-
sive silicone to back side
of LED after making all
connections and testing.
Optional Enhanced
Weather Protection
(EWP) Available*
(2) 0.156
diameter
type 2
mounting
holes
0.15 (0.19 EWP)
3.50 (3.58 EWP)
3.20
2.0
(2.04
EWP)
0.63
(0.67
EWP
1.5
2.63
(2.71
EWP)
Gray (N.C.)
Blue (COM)
Yellow (N.O.)
Black
Red
Black
Black
Red**
Red**
White
White
Black
Red
- Black
+ Red
Black
Black
Red**
Red**
White
White
- Black
+ Red
LED
Help/Call Switch
Info Switch
(optional)
Speaker
Mic
Connector and Wires from
Existing Standard (non EWP)
1600A Series Analog
Emergency Phone
FIGURE 1
Replacement Cable Assembly (included)
- OR -
Replacement connectors, wires and
butt connectors for use when replacing
EWP circuit boards or circuit boards from
models E-10A, E-20B, W-1000, W-2000A,
W-3000 or W-3005.
Optional 2 Amp Relay
Output Contacts Connector
Connect to doorstrike,
mag lock, gate controller, etc.
** Note: These two red wires are only
used on units with an Info button. When
installing on a single button unit, cut off
these two red wires and discard.
8 1 10 1
Note: This is a 1600-IP board (PCB) only kit. This kit can be used
to convert any Viking 1600A Series analog emergency phone to a
VoIP version. The kit can also be used to replace a damaged
board in the field.
Shipping Weight: .45 kg (1 lb)
Connections: (1) RJ45 10/100 Base-T, (3) optional gel-filled butt
connectors, (10) additional gel-filled butt connectors included with
EWP version only.
Optional Enhanced Weather
Protection (EWP) Available*
*Optional Enhanced Weather Protection (EWP): The op-
tional EWP products feature foam rubber gaskets and boots,
sealed connections, gel-filled butt connectors, as well as ure-
thane or thermal plastic potted circuit boards. See DOD# 859.
Step 1.
Cut wires from J1 (10 pin connector) and J2 (2 pin
connector).
Step 2.
Remove the two #6 phillips screws fastening the
circuit board.
Step 3.
Cut off any stripped wire ends from the replace-
ment cable.
Step 4.
Using the supplied gel-filled butt connectors, con-
nect corresponding wires from replacement cable
to the previously cut wires from the LED, Help/Call
switch, optional Info switch, Speaker and Micro-
phone. See FIGURE 1 for wire color and polarity.
Replacing Analog 1600A Series EWP Potted Circuit Boards: