Product manual
E-1600-22-IP / E-1600-32-IP
"Info" Push to Call Button
(E-1600-22-IP only)
Grade 2 Braille Label
Call Connected Red LED
"Help" Push to Call Button
E-1600-22-IP
Faceplate
** Adhere gasket to front
panel, centering over
mounting holes
"Old Work" Double Gang
Rough-In Box (Allied Molded
9312 box shown, not included)
(4) Optional Dry Wall
Screws (not included)
Optional VE-5x5 Surface Mount Box with black satin powder paint finish, not
included (DOD# 424). Optional VE-LIGHT kit can be used to illuminate the faceplate
when used with a VE-5x5 (DOD# 428). WARNING: Do NOT use a wet location box.
2.25”
5.14”
5.22”
3.25”
3.63”
3.63”
-OR-
(2) Junction Box to Double
Gang Adapter Plates and
(4) 5/64 Hex Drive Flat
Head Screws (included)
3.65"
Wide
Min.
2.84"
Tall Min.
***2.25"
Deep
Min.
HELPINFO
CONNECTED
CONNECTED
Call
V
IKING
©
-OR-
Marine grade 316 stainless steel
faceplate and push button
switches (sealed per IP67)
(4) 6-32 X 3/4” Marine
grade 316 stainless steel,
flat head, 5/64" hexdrive
screws (included)
E-1600-32-IP
Faceplate
**** 3/4”
Knockout
Optional Enhanced Weather
Protection (EWP) Available*
Dimensions: Overall - 127mm x 127 x
57mm (5.0” x 5.0” x 2.25”)
Shipping Weight: 1 kg (2.12 lbs.)
Front Panel Material: 14 gauge Marine
grade 316 brushed stainless steel
Connections: Gel-filled butt connectors
*Optional Enhanced Weather Protection (EWP): The optional EWP products feature
foam rubber gaskets and boots, sealed connections, gel-filled butt connectors, as well as
urethane or thermal plastic potted circuit boards. See DOD# 859.
Mounting in a Double Gang Rough-In Box (not included): Flush into walls, mounts to
side of wall studs, etc. Mounting with Optional VE-5x5: Surface mount to walls, single
gang boxes, double gang boxes, posts, or to a Viking VE-GNP Gooseneck pedestal (see
DOD# 424 for more information).
Note: When mounting outside to rough or uneven surfaces (brick, stucco, etc.) apply a
bead of clear silicone caulking around the top edge and sides of faceplate or VE-5x5.
*** CAUTION: Excessive wire length and/or using a rough-in
box with inadequate depth can apply force to the circuit board
causing physical damage.
** Note: Peel off paper liner and adhere gasket to the back
of the faceplate, centering it over the mounting holes.
**** Caution: When warm air comes in contact with cold surfaces, such as outside walls and conduits, it causes condensation. To prevent
condensation from accumulating inside the E-1600-22-IP or E-1600-32-IP always bring conduit into the bottom of the unit. If this is not
possible, drill a 1/4” diameter hole in the bottom of the black plastic box.
E-1600-30-IP
Front View of Optional
VE-5x5 (not included)
2.25”
** Adhere gasket to front
panel, centering over
mounting holes
5.14”
5.22”
3.25”
4.0"
Condensation Drain Hole
***Optional Braille Label
5.0”
Call Connected
Red LED
Rear View of VE-5x5
(not included)
Condensation
Drain Hole
(2) 0.2 x 0.43 slots
for single gang box
(4) 0.38” diameter holes
3.0” 3.3”
3.0”
2.1”
**** 3/4"
Knockout
for conduit
Wall Stud
Front View of
Plastic Rough-In
Box (included)
Wire knock out
(2) Standard flat head dry wall
(sheet rock) screws (not included)
CONNECTED
Marine grade
316 stainless steel
faceplate and push
button switches
(sealed per IP67)
(4) 6-32 X 3/4” Marine grade 316 stainless steel,
flat head, 5/64" hexdrive screws (included)
Push to Call
Button
(4) 0.2 x 0.43 slots
for double gang box
*** Important: Optional Braille “Push for Help” label should be adhered to the faceplate in ADA applications. Clean surface with isopropyl
alcohol, peel off backing and press firmly to the front panel in location as shown above.
** Note: Peel off paper liner and adhere gasket to the back of the faceplate, centering it over the mounting holes.
**** Caution: When warm air comes in contact with cold surfaces, such as outside walls and conduits, it causes condensation.
To prevent condensation from accumulating inside the E-1600-30-IP always bring conduit into the bottom of the unit. If this is not
possible, drill a 1/4” diameter hole in the bottom of the black plastic box.
Optional Enhanced Weather
Protection (EWP) Available*
Dimensions: Overall - 127mm x 127 x 57mm
(5.0” x 5.0” x 2.25”), Plastic Electrical Box -
102mm x 102mm x 54mm (4.0” x 4.0” x 2.14”)
Shipping Weight: 1 kg (2.12 lbs.)
Front Panel Material: 14 gauge Marine grade
316 brushed stainless steel
Connections: Gel-filled butt connectors
*Optional Enhanced Weather Protection
(EWP): The optional EWP products feature
foam rubber gaskets and boots, sealed connec-
tions, gel-filled butt connectors, as well as ure-
thane or thermal plastic potted circuit boards.
See DOD# 859.
Mounting with Plastic Rough-In Box (in-
cluded): Flush into walls, mounts to side of wall
stud Mounting with Optional VE-5x5: Surface
mount to walls, single gang boxes, double gang
boxes, posts, or to a Viking VE-GNP Gooseneck
pedestal.
Note: When mounting outside to rough or un-
even surfaces (brick, stucco, etc.) apply a bead
of clear silicone caulking around the top edge
and sides of faceplate or VE-5x5.
7
Important: The E-1600-30-IP will NOT mount
to a standard double gang box. If your applica-
tions requires a double gang box, see model E-
1600A-32-IP above.