Product manual
6
Front View of Optional
VE-5x5 (not included)
2.25”
** Adhere gasket to front panel,
centering over mounting holes
5.14”
5.22”
3.25”
4.0"
"Help" Push to Call Button
Call Connected Red LED
"Info" Push to Call Button
5.0”
Grade 2 Braille Label
Rear View of VE-5x5
(not included)
Condensation
Drain Hole
(4) 0.38” diameter
(4) 0.2 x 0.43 slots
for double gang box
(2) 0.2 x 0.43 slots
for single gang box
*** 3/4"
Knockout
3.0” 3.3”
3.0”
2.1”
*** 3/4"
Knockout
for conduit
Wall Stud
Front View of
Plastic Rough-In
Box (included)
Wire knock out
(2) Standard flat head dry wall
(sheet rock) screws (not included)
INFO
HELP
EMERGENCY
PHONE
CALL
CONNECTED
Marine grade
316 stainless
steel faceplate
and push
button switches
(sealed per IP67)
(4) 6-32 X 3/4” Marine grade 316
stainless steel, flat head, 5/64"
hexdrive screws (included)
Condensation Drain Hole
E-1600-20-IP
Optional Enhanced Weather Protection (EWP) Available*
E-1600-03-IP
Dimensions: 183mm x 149mm x
39mm (7.22” x 5.36” x 1.55”)
Material: 14 gauge Marine grade
316 brushed stainless steel panel
Shipping Weight: 1.36 kg (3 lbs.)
Connections: Gel-filled butt con-
nectors
Mounting: Surface mount to
walls, posts, single gang boxes,
double gang boxes or 4” x 4” elec-
trical junction boxes or recess
mount in elevator phone boxes.
*Optional Enhanced Weather
Protection (EWP): The optional
EWP products feature foam rubber
gaskets and boots, sealed con-
nections, gel-filled butt connectors,
as well as urethane or thermal
plastic potted circuit boards. See
DOD# 859.
Note: For greater weather resist-
ance, apply a bead of clear silicon
caulking around the top edge and
sides of the chassis.
7.22
5.36
(2) 8-32 x .5"
set screws
provided
1.55
CALL
CONNECTED
EMERGENCY
PHONE
MODEL E-1600-03-IP
VIKING
©
PUSH FOR
VIKING
©
HELP
Marine grade 316 stainless steel faceplate
and push button switch (sealed per IP67)
(Front View)
0.781
dia.
1.70
3.40
1.70
3.40
5.00
6.78
1.69
0.80
3.30
2.605
0.795
(Mounting Plate)
(Bottom View)
Condensation
Drain Hole
(4) .22 dia
mounting
holes
(4) .187 x .50
slots for
double
gang box
(2) .187 x .50
slots for
single
gang box
Push to Call button
Call Connected LED
Grade 2 Braille Label
** Note: Peel off paper liner and adhere gasket to the back of the faceplate, centering
it over the four corner mounting holes.
The black plastic rough-in box (part # 259576)
may be purchased separately (Example: Mount-
ing boxes to studs before the walls are finished for
flush installation). Go to www.vikingelectron-
ics.com and click on “Spare Parts” to order these
rough-in boxes.
Important: The E-1600-20-IP will NOT mount to a standard double gang box. If your
applications requires a double gang box, see model E-1600A-22-IP on page 7.
Optional Enhanced Weather
Protection (EWP) Available*
Dimensions: Overall - 127mm x 127 x 57mm
(5.0” x 5.0” x 2.25”), Plastic Electrical Box -
102mm x 102mm x 54mm (4.0” x 4.0” x 2.14”)
Shipping Weight: 1 kg (2.12 lbs.)
Front Panel Material: 14 gauge Marine grade
316 brushed stainless steel
Connections: Gel-filled butt connectors
*Optional Enhanced Weather Protection (EWP): The optional EWP products feature
foam rubber gaskets and boots, sealed connections, gel-filled butt connectors, as well
as urethane or thermal plastic potted circuit boards. See DOD# 859.
Mounting with Plastic Rough-In Box (included): Flush into walls, mounts to side of
wall stud Mounting with Optional VE-5x5: Surface mount to walls, single gang boxes,
double gang boxes, posts, or to a Viking VE-GNP Gooseneck pedestal (see DOD# 424
for more information).
Note: When mounting outside to rough or uneven surfaces (brick, stucco, etc.) apply
a bead of clear silicone caulking around the top edge and sides of faceplate or VE-5x5.
*** Caution: When warm air comes in contact with cold surfaces, such as outside walls and conduits,
it causes condensation. To prevent condensation from accumulating inside the E-1600-20-IP always
bring conduit into the bottom of the unit. If this is not possible, drill a 1/4” diameter hole in the bottom
of the black plastic box.