Specifications
To gain system access call (from a Touch Tone phone) the C.O. line or PABX extension connected to the DVA-
3003’s channel 1 CO/PABX LINE port. When the unit answers, enter a ✱. When the recording stops, enter your
six digit security code (factory set to 8,4,5,4,6,4,). Two beeps should then be heard, confirming the correct
security code was entered. You are now in the remote recording mode. Follow the recording, monitoring, and
programming steps in sections 3 - 5.
Note: Remove the handset and tape input plug from the DVA-3003 before remote recording.
REC/MON/ANNOUNCE Button
Selects Record or Announce Mode.
PLAY/OFF RECORD Button
Press this button to select Play, Off or Record modes.
Handset Jack
Use a standard carbon handset.
Recording
A. Local Recording
MODEL DVA-3003
VIKING
©
CHANNEL
1 2 3
REC/MON
ANNOUNCE
TAPE IN
AUDIO
LEVEL
START
VOLUME
PLAY
OFF
REC
CHANNEL 1
1. Recording Live
B. Local Monitoring
1. With the REC/MON mode selected, (see step a. above) place only one channel at a time into the PLAY mode
and place the other two channels into the OFF mode.
2. Momentarily press the START button to start and stop the announcement.
3. Any or all of the announcements can be rerecorded if needed. Follow the “local recording” procedures listed
above.
ON
E & M
RING
TRIP
SINGLE
CHANNEL
C. Remote Recording and Programming
3. Recording
5
1/8” Audio Input Jack
Permits downloading the announcement from a tape player.
Playback Volume Adjusts the playback volume.
START Button Momentarily press to start and stop recording.
LED Flickers to indicate correct tape in volume level.
a. Press the REC/MON button until the REC/MON LED lights to select REC/MON mode.
b. One, any two, or all three channels may be recorded at the same time. Select REC for the channels to be
recorded. Select OFF for any channels not to be recorded.
c. Connect a standard carbon handset to the handset jack.
d. Momentarily press the START button and begin speaking into the handset.
e. When finished, press the START button to stop recording.
2. Recording from a Tape
a. Press the REC/MON button until the REC/MON LED lights to select REC/MON mode.
b. One, any two, or all three channels may be recorded at the same time. Select REC for the channels to be
recorded. Select OFF for any channels not to be recorded.
c. Insert a 3.5mm (1/8”) phono plug cable into the TAPE IN jack.
d. Adjust the tape player to the correct audio recording volume, play the recording from the tape player while
watching the audio level LED. Increase or decrease the tape players volume until the LED flickers but is not
mostly on or mostly off.
Note: A handset may be used to monitor the tape player while down loading the recording.
e. When you are ready to record, momentarily press the START button and begin recording.
f. When you are finished, press the START button to stop recording.
To gain system access call (from a Touch Tone phone) the C.O. line or PABX extension connected to the DVA-
3003’s PROGRAMMING PORT. The unit will answer and give two beeps. You are now in the remote recording
mode. Follow the recording, monitoring, and programing steps in sections 3 - 5.
2. Four Wire E & M Interface Mode
4. Monitoring
One, two, or all three channels can be recorded at the same time. Enter 1 and/or 2 and/or 3 to select the
channel(s) to be recorded, then enter a ✱ to start and a # to stop recording.
Enter ✱ 4 to play back channel 1.
Enter ✱ 5 to play back channel 2.
Enter ✱ 6 to play back channel 3.
1. Ring Trip Interface Mode