Viking Installation Guide Viking Range Corporation 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For product information, call 1-888-VIKING1 (845-4641) or visit the Viking Web site at vikingrange.
IMPORTANT - PLEASE READ AND FOLLOW •Before beginning - please read these instructions completely and carefully •Do not remove permanently affixed labels, warnings, or rating plates from the dishwasher. This may void warranty. •Please observe all national and local codes. •Please ensure that this product is properly grounded. •The installer should leave these instructions with the consumer who should retain for local inspector’s use and for future reference.
CYCLE DATA CUTOUT DIMENSIONS DFUD042 AND DFUD142 DESCRIPTION Pots/Pans Heavy Normal Light/China Quick WATER TEMP. 140°F or 170°F (60°C or 75°C) 130°F or 160°F (55°C or 70°C) 130°F or 150°F (55°C or 65°C) 105°F or 120°F (40°C or 50°C) 85°F or 120°F (30°C or 50°C) Rinse/Hold DESCRIPTION PRE-WASH 2 MAIN WASH 1 RINSE 3 2 1 2 1 or 2 1 2 __ 1 2 __ 1 2 34 1/4” (87.0 cm) min. 37” (94.0 cm) max. 24”* (61.
WATER SUPPLY BASIC DIMENSIONS WARNING! 24” (61.0 cm) Plumbing connections must comply with applicable sanitary, safety and plumbing codes. Water pressure for the water supply should be minimum 18 to 176 psi. The dishwasher is supplied with a 6’ (1.8 m) PEX water supply line that has a 3/8” (.95 cm) NPT female connection. After determining where the water supply line will enter the dishwasher, drill a 1 1/2” (3.8 cm) access hole and run the line to the approximate fill valve location shown in the figure.
DRAIN ELECTRICAL CONNECTIONS A rubber drain hose (7/8” [2.2 cm]) is provided with the dishwasher which is connected to the back of the unit to form a high loop. The access hole for the drain line should be 1 1/2” (3.8 cm) at a minimum of 20” (50.8 cm) from the floor. If the hose provided is not long enough, extend it with a 7/8” (2.2 cm) copper tube. Do not use any fittings anywhere in the drain line that are less than 7/8” (2.2 cm) ID.
Moving the Machine Into Place ADJUSTING THE LEVELING LEGS Position the machine in front of the cabinet opening. Make the preliminary height adjustment while the dishwasher is in front of the opening. Pull out the drain hose to ensure there are no sharp bends. On the bottom rear of the dishwasher there is a black ziptie around the rubber buffer that holds the circulation pump in place. Cut the ziptie and remove it. Start to feed the water, electric,and drain lines into position.
FASTENING THE DISHWASHER TO THE CABINET WARNING! The dishwasher door will not stay open by itself until the door panel is installed. Be aware of this when fastening the dishwasher to the cabinet. Fasten the dishwasher to a kitchen cabinet using the 1” (2.5 cm) screws provided. NOTE: It is necessary to secure the dishwasher with screws so that it does not tilt if something heavy is placed on the door. 1. Using the screws and spacers, fasten the dishwasher to the cabinet through holes A. 2.
Before fitting the custom door front, the dishwasher must be installed underneath the cabinet. After making required measurements, it may be necessary to pull the unit out again to install the door front. 1. Fit handle (A) onto the panel according to the manufacturer’s instructions (NOTE: A handle should be used rather than a knob, because a knob does not provide enough grip.) 2. Loosen the screws (D) on the outer edge of the dishwasher. 3.
