Viking Installation Guide Viking Range Corporation 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For more product information, call 1-888-VIKING1 (845-4641) or visit the Viking Web site at vikingrange.
IMPORTANT: PLEASE READ AND FOLLOW SPECIFICATIONS - VECU ELECTRIC COOKTOP •Before beginning, please read these instructions completely and carefully. •Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty. •Please observe all local and national codes and ordinances. •Please ensure that this product is properly grounded. •The installer should leave these instructions with the consumer who should retain for local inspector’s use and for future reference.
ELECTRICAL REQUIREMENTS PROXIMITY TO SIDE CABINET INSTALLATION Check your local codes regarding this unit. This cooktop is supplied with a 3-wire, A.C. 208/120 volt or 120/240 volt, 60 HZ electrical system. A white (neutral) is not needed for this unit. See next section for grounding instructions. It should be fused separately. CAUTION: Be sure the electric power is off from the breaker box to the junction box until the cooktop is installed and ready to operate.
30” W. VECU TOP WOOD/COMPOSITE OVERLAY INSTALLATION The bottom of the hood should be 30” (76.2 cm) min. to 36” (91.4 cm) max. above the countertop. This would typically result in the bottom of the hood being 66” (167.6 cm) to 72” (182.9 cm) above the floor. Refer to the rangehood installation instructions for further information. These dimensions provide for safe and efficient operation of the hood. WALL INSTALLATION ISLAND INSTALLATION 21” (53.
36” W. VECU TOP INSTALLATION OF HOLD DOWN BRACKET - VECU MODELS Front Brackets After installating cooktop with two of the sheet metal Countertop screws (Item 1), locate the sheet metal screw hole in the rear of the burner box. Screw hold down brackets (Item 2) using the third sheet metal screw (Item 3) to the burner box. 21” (53.3 cm) Cooktop Item 1 Item 2 36 3/4” (93.3 cm) Item 3 36” W. VECU BURNER BOX Indentification Label Location Rear and Side Brackets 1.
DIMENSIONS 36” W. DECU TOP DECU HEIGHT 4 1/2” (11.4 cm) 3 1/2” (8.9 cm) 21” (53.3 cm) 3 1/16” (7.7 cm) 30” W. DECU TOP 36 3/4” (93.3 cm) 21” (53.3 cm) 30 3/4” (78.1 cm) Indentification Label Location 36” W. DECU BURNER BOX Indentification Label Location 30” W. DECU BURNER BOX Hold down bracket (one on each side) 19 11/16” (50.0 cm) 19 11/16” (50.0 cm) Hold down bracket (one on each side) 1 3/16” (3.0 cm) 1 3/16” (3.0 cm) 34 5/8” (87.9 cm) 1 3/16” (3.0 cm) 1 3/16” (3.0 cm) 28 1/2” (72.
45” W. DECU TOP INSTALLATION OF HOLD DOWN BRACKET - DECU MODELS Top of cooktop 21” (53.3 cm) Two (2) hold brackets will be provided with your unit. After cooktop has been installed into the countertop, locate the bracket in the slots as needed (Figure 1). Place a bracket in the slots and lower until the bracket catches. (Figure 2). Use the bolt to tighten the cooktop to the countertop. (Figure 3) Slots Figure 1 45” (114.3 cm) Mounting bracket Figure 2 45” W.
PERFORMANCE CHECKLIST A qualified installer should carry out the following checks: 1. Check top surface elements - glow red when turned on. 2. Check hot surface indicator lights - glow red when corresponding element is hot. Any adjustments necessary that are a result of the installer not following instructions will be the responsibility of the installer, dealer of the end user of this product. FINAL PREPARATION 1. Some stainless steel parts may have a plastic protective wrap which must be peeled off. 2.
