INSTALLATION INSTRUCTIONS FOR SHOWER ENCLOSURE er tron OWNER'S MANUAL Packing List PLEASE READ INSTRUCTIONS BEFORE PROCEEDING Wall mount brackets (2pc) Fixed panel holders {2pc) Rollers (4pc) Fixed panel {1pc} Door {1pc} Handle assembly (1pc) Fixed panel bottom clip {1 pc) Bottom door guide (1 pc) Door threshold {1pc} 10. Door stopper (2pc} 11. Structural rail (1pc) 12. Side seal strip (2pc) 13. Door seal strip (2pc + 1 extra) 14. Door bottom seal strip (1pc) 15. Phillips screws 1 1/8" (2pc) 16.
HTTP. /mwww.vigoindustries.com 1-866-591-7792 1. WALL MOUNT BRACKET ASSEMBLY 98018 2. FIXED PANEL HOLDER 98026 S 3. ROLLERS 98020 @y 4. FIXED PANEL 97017-86 &. DOOR 07018 6. HANDLE ASSEMBLY FIXED PANEL BOTTOM CLP 98029 © 8. BOTTOM DOOR GUIDE 98030 8 9. DOOR THRESHOLD 96007-38 96007-40 = x 10. DOOR STOPPER 98024 = O 11. STRUCTURAL RAIL 12. SIDE SEAL STRIP 13. DOOR SEAL STRIP 14. DOOR BOTTOM 16. PHILLIPS SCREW SEAL STRIP 11/8 fend 86001 86013 88014 + 16. PHILLIPS SCREW 2" 17. PLASTIC ANCHORS LIST DIM. "A DIM.
HTTP. /mwww.vigoindustries.com BEFORE STARTING 1-866-591-7792 Upon receipt, verify if your shower enclosure is in good condition and make sure that all parts are included in the hardware bag. If you are missing a part, please contact your distributor immediately.
HTTP. /mwww.vigoindustries.com STEP 1: INSTALLATION 1-866-591-7792 1. Due to individual site variations, exact guidelines for every situation cannot be supplied. The recommended framing and dimensional requirements shown are for a typical application and may vary depending on the site requirements. 2. Your shower enclosure should be installed in a leveled wall opening. 3. Ensure that there is sufficient structural support behind your shower wall to bare the weight of the door.
HTTP. /mwww.vigoindustries.com 1-866-691-7792 ‘OUTSIDE OF THE SHOWER TOP VIEW FIG. 5 STEP 3: DOOR INSTALLATION 1. Screw top rollers (3) to the door (5), see FIG. 6. 2. Place door (5) to the structural rail (11), see FIG. 7. 3. Screw bottom rollers (3) to the door (7), see FIG. 8.
HTTP. /mwww.vigoindustries.com OUTSIDE OF THE SHOWER 1-866-591-7792 5 5 +s INSIDE OF THE SHOWER TOP VIEW STEP 4: THRESHOLD INSTALLATION 1. Seal bottom of end cup with clear silicon. 2. Seal bottom side of the threshold (9) with clear silicon. 3. Slide end cup to the fixed panel (4). Align threshold with the door FIG. 8 and press down firmly.
HTTP. /mwww.vigoindustries.com 1-866-691-7792 STEP 5: HANDLE INSTALLATION 1. Unscrew handle holders from the handle (6). 2. Place handle to the position on the door with plastic washer on each side of the door (FIG. 8) 5 3. Tighten handle holders from inside of the shower. 6 THIS END MUST LOOK INSIDE THE SHOWER FIG.
STEP 6: SEAL STRIP INSTALLATION 1. Place seal strip to the door and to the glass, see FIG. 10, page 7. STEP 7: SILICONE. 1. Apply silicone all along the wall and floor on the interior of the shower enclosure. NOTE: DO NOT ALLOW DIRECT WATER ONTO DOOR SEAL STRIP. WAIT 24 HOURS BEFORE USING THE SHOWER. CLEANING surface. solution, lacquer thinner, gasoline, etc. Remove dust with a soft, damp cloth. Clean grease, oil, paint and ink with rubbing alcohol. "mu 0 wp polish. MODEL VG06031 HTTP. /mwww.vigoindustries.
hit. ffwww.vigoindustries.com 1-866-581-7782 LIMITED WARRANTY VIGOR offers the following express limited warranty on each of #ts products, This warranty extends only to the original for personal household use. For commercial uses, additional limitations apply. VIGOR warrants acrylic units to be free from defects in workmanship and materials under normal use and service for a period of twenty (20) years from the initial date of purchase by the contractor or builder from an authorized dealer.
