Specification
3.
SUPPORT
ASSEMBLY
4.
SIDE PANEL
5.
SIDE SEAL STRIP
6. GLASS SUPPORT 7.
HINGE ASSEMBLY
8.
BOTTOM RAIL
9.
MAGNETIC SEAL STRIP
10.
CORNER JOINT
11.
DOOR HANDLE
ASSEMBLY
12.
DOOR
PLASTIC ANCHOR
14.
A
A
B
B
C
15.
HEX SCREW 1 1/8"
DOOR BOTTOM SEAL
STRIP
18.
1.
2.
WALL CONNECTOR
STRUCTURAL ARM
98001
98002-42
98002-47
98003
97001-42
97001-47
98004 98015 95001-42
95001-47
96011
94001
97002-12
96004
96001
17. PHILLIPS SCREW 3/4"
16. HEX SCREW 1 5/8"
98014
96035
98039 98033 98037
PLASTIC ANCHOR
19.
98038
HEX SCREW COVER
20.
96040
A, B & C DIMENSIONS WERE MEASURED AFTER SHOWER ENCLOSURE WAS COMPLETELY
INSTALLED
45 5/8"
13.
DOOR SIDE SEAL
STRIP
96003
DIM. "A" DIM. "B"
MODEL
#12- DOOR (97002)
#4- SIDE GLASS
PANEL (97001)
26"x71 5/8"
20 1/2"x71 5/8"
12 5/8"x70 3/8"
12 5/8"x70 3/8"
47 X 47
42 X 42
DIM. "C"
* - GLASS AND HARDWARE ONLY (FULLY INSTALLED)
HEIGHT
73 3/8"
73 3/8"
40"
26 5/8"
21 1/8"
26 7/8"
26 7/8"
CLEAR PVC SHIM
MISC
21.
ALLEN KEY PACK
MISC
22.
3
MODEL VG06063
26 1/2"
26 1/2"
DOOR OPENING
WIDTH
Product lines may change, contact your Vigo representative at 1-866-591-7792 or visit
our website at www.vigoindustries.com for the most up to date product line information.
3.
SUPPORT
ASSEMBLY
4.
SIDE PANEL
5.
SIDE SEAL STRIP
6. GLASS SUPPORT 7.
HINGE ASSEMBLY
8.
BOTTOM RAIL
9.
MAGNETIC SEAL STRIP
10.
CORNER JOINT
11.
DOOR HANDLE
ASSEMBLY
12.
DOOR
PLASTIC ANCHOR
14.
A
A
B
B
C
15.
HEX SCREW 1 1/8"
DOOR BOTTOM SEAL
STRIP
18.
1.
2.
WALL CONNECTOR
STRUCTURAL ARM
98001
98002-42
98002-47
98003
97001-42
97001-47
98004 98015 95001-42
95001-47
96011
94001
97002-12
96004
96001
17. PHILLIPS SCREW 3/4"
16. HEX SCREW 1 5/8"
98014
96035
98039 98033 98037
PLASTIC ANCHOR
19.
98038
HEX SCREW COVER
20.
96040
A, B & C DIMENSIONS WERE MEASURED AFTER SHOWER ENCLOSURE WAS COMPLETELY
INSTALLED
45 5/8"
13.
DOOR SIDE SEAL
STRIP
96003
DIM. "A" DIM. "B"
MODEL
#12- DOOR (97002)
#4- SIDE GLASS
PANEL (97001)
26"x71 5/8"
20 1/2"x71 5/8"
12 5/8"x70 3/8"
12 5/8"x70 3/8"
47 X 47
42 X 42
DIM. "C"
* - GLASS AND HARDWARE ONLY (FULLY INSTALLED)
HEIGHT
73 3/8"
73 3/8"
40"
26 5/8"
21 1/8"
26 7/8"
26 7/8"
CLEAR PVC SHIM
MISC
21.
ALLEN KEY PACK
MISC
22.
3
MODEL VG06063
26 1/2"
26 1/2"
DOOR OPENING
WIDTH
Product lines may change, contact your Vigo representative at 1-866-591-7792 or visit
our website at www.vigoindustries.com for the most up to date product line information.
STUD
FIG.1
90°
90°
135°
PREPARATION STEPS TO FOLLOW BEFORE INSTALLATION
1. Remove the plastic layer from the base border (if needed). Do NOT remove the plastic layer off the plastic
platform of the base.
2. Properly apply silicone to the wall and base joints.
3. Make sure to read corresponding base instructions carefully prior to install on the Vigo Brand Shower Door
System. Failure to do so can cause water leakage and bodily harm.
IMPORTANT
To prevent damage to the finish, you should protect the shower cabin bottom with a cardboard protector
before beginning the installation.
Ensure that there is sufficient structural support behind the shower wall to hold the weight of the shower
door. If there is insufficient support, then reinforce the shower walls with wooden studs prior to shower door
installation. [SEE FIG.1]
CAUTION
!
GASKETS NEED TO BE IN BETWEEN ALL GLASS AND METAL CONTACT. FAILURE TO DO SO
CAN LEAD TO BREAKAGE AND POTENTIAL BODILY HARM.
5
MODEL VG06063
SIDE GLASS
PANEL
DOOR PANELS SIDE GLASS
PANEL
FIG. 1A (GLASS CONFIGURATION DIAGRAM)
4
12
4
MODEL VG06063
4
WARNING
WE STRONGLY RECOMMEND THAT A LICENSED PROFESSIONAL INSTALL THIS SHOWER
ENCLOSURE AND INCLUDE THE ASSISTANCE OF A SECOND PERSON TO INSTALL THE DOOR UNIT.
!
INSTALLATION OF THE SHOWER DOORS BY AN INEXPERIENCED PERSON MAY RESULT IN
GLASS BREAKAGE AND, CONSEQUENTLY, CAUSE PERSONAL INJURY OR DEATH.
- Handle fragile items with care to prevent personal injury or material damage.
- The glass panels are tempered and cannot be cut. Never attempt to do so.
- Always rest glass on a level surface
REQUIRED TOOLS
Square and/or Phillips #1 and #2 screwdriver
Flat head screwdriver
Electric drill plus 1/32", 3/32", 1/8" and 3/16" drill bit (depending on wall)
Level
Measuring tape
Pencil (non-permanent)
Clear silicone caulking
Utility knife
WARNING
!
Handle fragile items with care to prevent injury or material damage.
Glass on panels and doors is tempered glass and must never be cut to prevent personal injury.
IMPORTANT
Fiberglass, acrylic or sheetrock construction might not be sufficiently strong enough to support
the shower door enclosure. You should use the wood framing studs from behind the face edge of
the stall to provide a secure mounting to the door. Apply a bead of silicone between the walls and
base of the stall.
For optimum performance, you should install the shower door perfectly level on a level surface.
Failure to do so will lead to water leakage and potential property damage.
When installing use heavy duty gloves.
IMPORTANT:
THE CLEAR GLASS MODEL HAS A REVERSIBLE DOOR AND CAN BE INSTALLED TO THE RIGHT OR LEFT SIDE.
(SEE CONFIGURATION DIAGRAM BELOW)
BEFORE STARTING
Compare items on your invoice with what you have received. Carefully review the Packing List on page 2. If
any items are missing contact Vigo Industries at 1-866-591-7792. Please check our website at
www.vigoindustries.com for additional information or instructional videos.
SIDE GLASS
PANEL
DOOR PANELS SIDE GLASS
PANEL
FIG. 1A (GLASS CONFIGURATION DIAGRAM)
4
12
4
MODEL VG06063
4
WARNING
WE STRONGLY RECOMMEND THAT A LICENSED PROFESSIONAL INSTALL THIS SHOWER
ENCLOSURE AND INCLUDE THE ASSISTANCE OF A SECOND PERSON TO INSTALL THE DOOR UNIT.
!
INSTALLATION OF THE SHOWER DOORS BY AN INEXPERIENCED PERSON MAY RESULT IN
GLASS BREAKAGE AND, CONSEQUENTLY, CAUSE PERSONAL INJURY OR DEATH.
- Handle fragile items with care to prevent personal injury or material damage.
- The glass panels are tempered and cannot be cut. Never attempt to do so.
- Always rest glass on a level surface
REQUIRED TOOLS
Square and/or Phillips #1 and #2 screwdriver
Flat head screwdriver
Electric drill plus 1/32", 3/32", 1/8" and 3/16" drill bit (depending on wall)
Level
Measuring tape
Pencil (non-permanent)
Clear silicone caulking
Utility knife
WARNING
!
Handle fragile items with care to prevent injury or material damage.
Glass on panels and doors is tempered glass and must never be cut to prevent personal injury.
IMPORTANT
Fiberglass, acrylic or sheetrock construction might not be sufficiently strong enough to support
the shower door enclosure. You should use the wood framing studs from behind the face edge of
the stall to provide a secure mounting to the door. Apply a bead of silicone between the walls and
base of the stall.
For optimum performance, you should install the shower door perfectly level on a level surface.
Failure to do so will lead to water leakage and potential property damage.
When installing use heavy duty gloves.
IMPORTANT:
THE CLEAR GLASS MODEL HAS A REVERSIBLE DOOR AND CAN BE INSTALLED TO THE RIGHT OR LEFT SIDE.
(SEE CONFIGURATION DIAGRAM BELOW)
BEFORE STARTING
Compare items on your invoice with what you have received. Carefully review the Packing List on page 2. If
any items are missing contact Vigo Industries at 1-866-591-7792. Please check our website at
www.vigoindustries.com for additional information or instructional videos.