Specification

3.
SUPPORT
ASSEMBLY
4.
SIDE PANEL
5.
SIDE SEAL STRIP
6. GLASS SUPPORT 7.
HINGE ASSEMBLY
8.
BOTTOM RAIL
9.
MAGNETIC SEAL STRIP
10.
CORNER JOINT
11.
DOOR HANDLE
ASSEMBLY
12.
DOOR
PLASTIC ANCHOR
14.
A
A
B
B
C
15.
HEX SCREW 1 1/8"
DOOR BOTTOM SEAL
STRIP
18.
1.
2.
WALL CONNECTOR
STRUCTURAL ARM
98001
98002-42
98002-47
98003
97001-42
97001-47
98004 98015 95001-42
95001-47
96011
94001
97002-12
96004
96001
17. PHILLIPS SCREW 3/4"
16. HEX SCREW 1 5/8"
98014
96035
98039 98033 98037
PLASTIC ANCHOR
19.
98038
HEX SCREW COVER
20.
96040
A, B & C DIMENSIONS WERE MEASURED AFTER SHOWER ENCLOSURE WAS COMPLETELY
INSTALLED
45 5/8"
13.
DOOR SIDE SEAL
STRIP
96003
DIM. "A" DIM. "B"
MODEL
#12- DOOR (97002)
#4- SIDE GLASS
PANEL (97001)
26"x71 5/8"
20 1/2"x71 5/8"
12 5/8"x70 3/8"
12 5/8"x70 3/8"
47 X 47
42 X 42
DIM. "C"
* - GLASS AND HARDWARE ONLY (FULLY INSTALLED)
HEIGHT
73 3/8"
73 3/8"
40"
26 5/8"
21 1/8"
26 7/8"
26 7/8"
CLEAR PVC SHIM
MISC
21.
ALLEN KEY PACK
MISC
22.
3
MODEL VG06063
26 1/2"
26 1/2"
DOOR OPENING
WIDTH
Product lines may change, contact your Vigo representative at 1-866-591-7792 or visit
our website at www.vigoindustries.com for the most up to date product line information.
3.
SUPPORT
ASSEMBLY
4.
SIDE PANEL
5.
SIDE SEAL STRIP
6. GLASS SUPPORT 7.
HINGE ASSEMBLY
8.
BOTTOM RAIL
9.
MAGNETIC SEAL STRIP
10.
CORNER JOINT
11.
DOOR HANDLE
ASSEMBLY
12.
DOOR
PLASTIC ANCHOR
14.
A
A
B
B
C
15.
HEX SCREW 1 1/8"
DOOR BOTTOM SEAL
STRIP
18.
1.
2.
WALL CONNECTOR
STRUCTURAL ARM
98001
98002-42
98002-47
98003
97001-42
97001-47
98004 98015 95001-42
95001-47
96011
94001
97002-12
96004
96001
17. PHILLIPS SCREW 3/4"
16. HEX SCREW 1 5/8"
98014
96035
98039 98033 98037
PLASTIC ANCHOR
19.
98038
HEX SCREW COVER
20.
96040
A, B & C DIMENSIONS WERE MEASURED AFTER SHOWER ENCLOSURE WAS COMPLETELY
INSTALLED
45 5/8"
13.
DOOR SIDE SEAL
STRIP
96003
DIM. "A" DIM. "B"
MODEL
#12- DOOR (97002)
#4- SIDE GLASS
PANEL (97001)
26"x71 5/8"
20 1/2"x71 5/8"
12 5/8"x70 3/8"
12 5/8"x70 3/8"
47 X 47
42 X 42
DIM. "C"
* - GLASS AND HARDWARE ONLY (FULLY INSTALLED)
HEIGHT
73 3/8"
73 3/8"
40"
26 5/8"
21 1/8"
26 7/8"
26 7/8"
CLEAR PVC SHIM
MISC
21.
ALLEN KEY PACK
MISC
22.
3
MODEL VG06063
26 1/2"
26 1/2"
DOOR OPENING
WIDTH
Product lines may change, contact your Vigo representative at 1-866-591-7792 or visit
our website at www.vigoindustries.com for the most up to date product line information.
STUD
FIG.1
90°
90°
135°
PREPARATION STEPS TO FOLLOW BEFORE INSTALLATION
1. Remove the plastic layer from the base border (if needed). Do NOT remove the plastic layer off the plastic
platform of the base.
2. Properly apply silicone to the wall and base joints.
3. Make sure to read corresponding base instructions carefully prior to install on the Vigo Brand Shower Door
System. Failure to do so can cause water leakage and bodily harm.
IMPORTANT
To prevent damage to the finish, you should protect the shower cabin bottom with a cardboard protector
before beginning the installation.
Ensure that there is sufficient structural support behind the shower wall to hold the weight of the shower
door. If there is insufficient support, then reinforce the shower walls with wooden studs prior to shower door
installation. [SEE FIG.1]
CAUTION
!
GASKETS NEED TO BE IN BETWEEN ALL GLASS AND METAL CONTACT. FAILURE TO DO SO
CAN LEAD TO BREAKAGE AND POTENTIAL BODILY HARM.
5
MODEL VG06063

Summary of content (2 pages)