A VIGOR INDUSTRIES INSTALLATION GUIDE FOR SHOWER ENCLOSURE (MODEL VG06061) /\ SAFETY PRECAUTIONS This Installation Guide uses the following symbols to indicate important information. Always observe the instructions indicated by these symbols. /A WARNING Instructions that, if ignored, could result in death or serious personal injury caused by incorrect handling or installation of the product. These instructions must be observed for safe installation. /\ CAUTION The instructions for the following unit is base
INSTALLATION INSTRUCTIONS FOR STANDING SHOWER CABIN OWNER'S MANUAL PLEASE READ INSTRUCTIONS BEFORE PROCEEDING Packing List 1. Wall connector (2pc) 2. Structural am (2pc) 3. Support assembly (2pc) 4. Side glass panel (with hinge slots, 1pc) 5. Side glass pane! (without hinge slots, 1pc) 6. Side seal strip (2pc) 7. Glass support (4pc) 8. Hinge (2pc) 1 9. Bottom rail(3 pc) 10. Door magnetic seal strip (2pc) 1. Bottom corner joint (2pc) 12. Handle assembly (1pc) 13. Door (1pc) 14.
1. WALL CONNECTOR 2. STRUCTURAL ARM 3.SUPPORT ASSEMBLY]| . 4. SIDE GLASS PANEL 97001-38 97001-38 97001-40 97001-42 5. SIDE LASS PANEL 97006-35 97008-38 97008-40 9700842 8. SIDE SEAL STRIP 96001 7.GLASS SUPPORT 98004 8 HINGE ASSEMBLY 98015 > 9. BOTTOM RAIL 3pc. 85001-36 85001-38 85001-40 10. DOOR MAGNETIC SEAL STEP 98002 11. BOTTOM CORNER JOINT s 94001 12. DOOR HANDLE ASSEMBLY O 98014 @@ o 13. DOOR 97007-24 97007-25 95001-42 14. DOOR SIDE SEAL STEP 98003 15. DOOR BOTTOM SEAL STEP 98004 16.
/\ WARNING WE STRONGLY RECOMMEND THAT A LICENSED PROFESSIONAL INSTALL THIS SHOWER CABIN AND INCLUDE THE ASSISTANCE OF A SECOND PERSON TO INSTALL THE DOOR UNIT. INSTALLATION OF THE SHOWER DOORS BY AN INEXPERIENCED PERSON MAY RESULT IN GLASS BREAKAGE AND, CONSEQUENTLY, CAUSE PERSONAL INJURY OR DEATH. BEFORE STARTING Compare items on your invoice with what you have received. Carefully review the Packing List on page 2. If any items are missing contact Virgo Industries at 1-866-581-7792.
PREPARATION STEPS TO FOLLOW BEFORE INSTALLATION 1. Remove the plastic layer from the base border (if needed). Do NOT remove the plastic layer off the plastic platform of the base. 2. Properly apply silicone to the wall and base joints. &) IMPORTANT e« To prevent damage to the finish, you should protect the shower cabin bottom with a cardboard protector before beginning the installation. s Ensure that there is sufficient structural support behind the shower wall to hold the weight of the shower door.
THIS EDGE LOOKS ~ INSIDE OF THE SHOWER TOP REMOVES TO A INSTALL 34 SCREW THIS EDGE LOOKS 11 7 OUTSIDE QF THE SHOWER Fig B. INSTALLING SIDE GLASS PANEL 1. Arrange glass to the preferred configuration. (see diagram on page 4) 2. Select the door opening location on the shower cabin. 3. Install the side seal strip (#6) to the wall side of the hinged side glass panel! [SEE FIG.3] 4. Screw in the glass support (#7) to the side glass panel using the hex key (supplied).
C area— HEBREW GLASS SUPPORT (7) ji J SIDE GLASS PANEL | S @CASKET 13 e oo VIEW FROM THE TOP < . HANDLE INSTALLATION \2 1. Assemble the door shandies (#12) to the door [SEE FIG 5] WALL: SCREW (17) FIG.4 12 oo FIGS HINGE INSTALLATION Clean the glass surface on the side glass panel (#4) where the hinges (#8) are to be installed with rubbing alcohol. Position hinges on the side glass panel. [SEE FIG.6] Place washers on each side of the side glass panel.
. INSTALLING THE WATER SEAL STRIP 1. Clean the side glass panel (#4) edges where the door side seal strip (#14) and the door bottom seal strip (#15) are to be installed with rubbing alcohol. 2. Cut the seal strips according to the diagram. [SEE FIG.7] 3. Verify that the lips of both seal strips face toward the inside of the shower cabin before seal strip installation. 4. |Install the seal strips according to the diagram. THIS SIDE MUST LOOK INSIDE THE CABIN 14 \ SEAL STRIP FROM THIS SIDE ALREADY ATTACHED TO
/\ WARNING DOOR PANEL INSTALLATION REQUIRES TWO OR MORE PEOPLE TO ASSIST F.INSTALLING THE DOOR 1. 2. 3. Clean the door (#13) glass surfaces where the hinges (#8) are to be installed with rubbing alcohol. Position the door onto the hinges. Hold securely in place. Place a thin gasket (supplied) on each side of the door between the glass and hinge while holding the door in place. Install the hinges as illustrated [SEE FIG.8]. Use the hex key supplied.
H. APPLYING THE SILICONE Apply clear silicone caulking to the inside between the wall and side seal strip. Apply clear silicone caulk to the inside between the bottom of side glass panels (#4, #5) and bottom rail. Apply clear silicone caulk around the inside perimeter of the bottom rail. [SEE FIG.10] INSTALLING HEX SCREW COVERS Install hex screw covers (#21) to the hex screws that mount the hinges, wall connectors, and glass supports. FIG.10 /I\ IMPORTANT s WAIT 24 HOURS BEFORE USING SHOWER o DO NOT ALLOW W
CLEANING INSTRUCTIONS FOR THE SHOWER CABIN AND DOOR PANEL A Sow Use mild liquid household cleaners to keep metal surface bright and clean. Rinse well and dry with a clean cloth. Remove dust with a soft, damp cloth. Use rubbing alcohol to clean and remove grease, oil, paint, and ink. Accidental scratches or stains will rarely show. If they do show, they can be easily removed with a liquid automobile polish. /\ IMPORTANT Do NOT use abrasive cleaners, scrapers, metal brushes, or any items/products that would s
VIGOR INDUSTRIES, LLC ("VIGOR) SHOWER ENCLOSURE LIMITED LIFETIME WARRANTY EFFECTIVE JANUARY 1, 2010 VIGOR offers the following limited warranty on each of its Shower Enclosure products* (the “Product”) and the components thereof. This warranty extends only to the original owner or end-user for personal household use. For commercial uses, additional imitations apply.
