Intel® Desktop Board D945GNT/D945GTP Product Guide Order Number: D10471-003
Revision History Revision -001 Revision History First release of the Date Intel® Desktop Board D945GNT/D945GTP Product Guide Intel® -002 Second release of the Product Guide -003 Added operating system support Desktop Board D945GNT/D945GTP March 2005 April 2006 February 2006 If an FCC declaration of conformity marking is present on the board, the following statement applies: FCC Declaration of Conformity This device complies with Part 15 of the FCC Rules.
Preface This Product Guide gives information about board layout, component installation, BIOS update, and regulatory requirements for Intel® Desktop Board D945GNT/D945GTP. Intended Audience The Product Guide is intended for technically qualified personnel. It is not intended for general audiences. Intended Uses All Intel desktop boards are evaluated as Information Technology Equipment (I.T.E.
Intel Desktop Board D945GNT/D945GTP Product Guide Terminology The table below gives descriptions to some common terms used in the product guide.
Contents 1 Desktop Board Features.................................................................................9 Manufacturing Options ........................................................................................................11 Supported Operating Systems ............................................................................................11 Desktop Board Components ...............................................................................................12 Processor............
Intel Desktop Board D945GNT/D945GTP Product Guide Installing and Removing the Desktop Board........................................................................31 Installing and Removing a Processor ..................................................................................32 Installing a Processor .................................................................................................32 Installing the Processor Fan Heat Sink ..............................................................
Contents B Regulatory Compliance Safety Regulations ..............................................................................................................67 European Union Declaration of Conformity Statement ........................................................67 Product Ecology Statements ...............................................................................................69 Lead-Free Desktop Board .......................................................................................
Intel Desktop Board D945GNT/D945GTP Product Guide Tables 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. viii Feature Summary ...........................................................................................................9 Manufacturing Options..................................................................................................11 Desktop Boards D945GNT Components ......................................................................
1 Desktop Board Features This chapter briefly describes the main features of Intel® Desktop Board D945GNT/D945GTP. Table 1 summarizes the major features of the desktop board. Table 1. Feature Summary Form Factors • ATX (12.00” x 9.60”) desktop board D945GNT • MicroATX (9.60” x 9.60”) desktop board D945GTP Processor Support for an Intel® processor in the LGA775 package Main Memory • Four 240-pin, 1.
Intel Desktop Board D945GNT/D945GTP Product Guide Table 1. Feature Summary (continued) Peripheral Interfaces • Up to eight USB 2.0 ports ⎯ Four ports routed to the back panel ⎯ Four ports routed to two USB headers • Four Serial ATA (SATA) channels (3.
Desktop Board Features Manufacturing Options Table 2 shows the manufacturing options for desktop board D945GNT/D945GTP. Table 2.
Intel Desktop Board D945GNT/D945GTP Product Guide Desktop Board Components Figure 1 shows the approximate location of the major components on desktop board D945GNT. IEEE 1394a (Optional) (Optional) Line In Optical Line Out (Toslink) (Optional) A B D C E F T G Intel R 82945G S (GMCH) H R Intel 82801 (ICH7) Channel A DIMM 0 R Channel A DIMM 1 Channel B DIMM 0 Channel B DIMM 1 Q P M O L K J I N OM17611 Figure 1.
Desktop Board Features Table 3.
Intel Desktop Board D945GNT/D945GTP Product Guide Figure 2 shows the approximate location of the major components on desktop board D945GTP. IEEE 1394a (Optional) (Optional) Line In Optical Line Out (Toslink) (Optional) B A C D E S F R Intel R 82945G (GMCH) G R Intel 82801 (ICH7) Channel A DIMM 0 Q Channel A DIMM 1 Channel B DIMM 0 Channel B DIMM 1 P O L N K J I H M OM17612 Figure 2.
Desktop Board Features Table 4.
Intel Desktop Board D945GNT/D945GTP Product Guide Processor CAUTION Failure to use the appropriate power supply (below) and/or not connecting the 12 V (2x2) power connector to the desktop board may result in damage to the board, or the system may not function properly. Table 5. Power Supply Requirements Platform Compatibility Guide Power Supply Requirements 05B 12V2 rating of 16 A continuous and 19 A peak current for 10mS 05A 12V2 rating of 13 A continuous and 16.
Desktop Board Features Main Memory NOTE To be fully compliant with all applicable Intel® SDRAM memory specifications, the board should be populated with DIMMs that support the Serial Presence Detect (SPD) data structure. If your memory modules do not support SPD, you will see a notification to this effect on the screen at power up. The BIOS will attempt to configure the memory controller for normal operation. The desktop board supports dual or single channel memory configurations defined in Table 6.
Intel Desktop Board D945GNT/D945GTP Product Guide Intel® 945G Express Chipset The Intel 945G Express Chipset consists of the following devices: • Intel 82945G Graphics and Memory Controller Hub (GMCH) with Digital Media Interface • Intel 82801GB I/O Controller Hub (ICH7) or Intel 82801GR I/O Controller Hub (ICH7R) supporting Intel Matrix Storage Technology • Firmware Hub (FWH) Related Link: Go to the following link for more information about the Intel 945G Express Chipset: http://developer.intel.
Desktop Board Features Related Links: Go to the following link or pages for more information about: • Audio drivers and utilities http://support.intel.
Intel Desktop Board D945GNT/D945GTP Product Guide RJ-45 LAN Connector LEDs Two LEDs are built into the RJ-45 LAN port located on the back panel (see Figure 3). OM17386 Figure 3. LAN Port LED Locations Two LEDs are built into the RJ-45 LAN connector. Table 7 describes the LED states when the board is powered up and the 10/100 Ethernet LAN subsystem is operating. Table 7.
Desktop Board Features Hi-Speed USB 2.0 Support NOTE Computer systems that have an unshielded cable attached to a USB port might not meet FCC Class B requirements, even if no device or a low-speed USB device is attached to the cable. Use a shielded cable that meets the requirements for a full-speed USB device. The desktop board supports up to eight USB 2.0 ports via ICH7 or ICH7R; four ports routed to the back panel and four routed to two internal USB 2.0 headers. USB 2.
Intel Desktop Board D945GNT/D945GTP Product Guide Related Links: For information about installing the PCI Express x16 card, see page 40 in Chapter 2. BIOS The BIOS provides the Power-On Self-Test (POST), the BIOS Setup program, the PCI/PCI Express and IDE auto-configuration utilities, and the video BIOS. The BIOS is stored in the Firmware Hub. The BIOS can be updated by following the instructions on page 59 in Chapter 3.
Desktop Board Features Chassis Intrusion The board supports a chassis security feature that detects if the chassis cover has been removed. The security feature uses a mechanical switch on the chassis that can be connected to the chassis intrusion header on the desktop board. See Figure 21 on page 43 for the location of the chassis intrusion header.
Intel Desktop Board D945GNT/D945GTP Product Guide Suspend to RAM (Instantly Available PC Technology) CAUTIONS For Instantly Available PC technology, the 5 V standby line for the power supply must be capable of delivering adequate +5 V standby current. Failure to provide adequate standby current when using this feature can damage the power supply and/or effect ACPI S3 sleep state functionality.
Desktop Board Features Wake from PS/2 Keyboard/Mouse PS/2 keyboard/mouse activity wakes the computer from an ACPI S1 or S3 state. PME# Wakeup Support When the PME# signal on the PCI bus is asserted, the computer wakes from an ACPI S1, S3, or S5 state. Speaker A speaker is mounted on the desktop board. The speaker provides audible error code (beep code) information during the Power-On Self-Test (POST).
Intel Desktop Board D945GNT/D945GTP Product Guide 26
2 Installing and Replacing Desktop Board Components This chapter tells you how to: • Install the I/O shield • Install and remove the desktop board • Install and remove a processor and memory • Install and remove a PCI Express x16 card • Connect the IDE and Serial ATA cables • Connect internal headers • Set up flexible 6-channel audio with jack re-tasking • Connect fans and power cables • Locate other connectors • Set the BIOS configuration jumper • Clear passwords • Replace the battery Before You Begin CAU
Intel Desktop Board D945GNT/D945GTP Product Guide Follow these guidelines before you begin: • Always follow the steps in each procedure in the correct order. • Set up a log to record information about your computer, such as model, serial numbers, installed options, and configuration information. • Electrostatic discharge (ESD) can damage components. Perform the procedures described in this chapter only at an ESD workstation using an antistatic wrist strap and a conductive foam pad.
Installing and Replacing Desktop Board Components If the power supply and other modules or peripherals, as applicable, are not Class B EMC compliant before integration, then EMC testing may be required on a representative sample of the newly completed computer. Chassis and Component Certifications Ensure that the chassis and certain components; such as the power supply, peripheral drives, wiring, and cables; are components certified for the country or market where used.
Intel Desktop Board D945GNT/D945GTP Product Guide Installing the I/O Shield The desktop board comes with an I/O shield. When installed in the chassis, the shield blocks radio frequency transmissions, protects internal components from dust and foreign objects, and promotes correct airflow within the chassis. Install the I/O shield before installing the desktop board in the chassis. Place the shield inside the chassis as shown in Figure 5. Press the shield into place so that it fits tightly and securely.
Installing and Replacing Desktop Board Components Installing and Removing the Desktop Board CAUTION Only qualified technical personnel should do this procedure. Disconnect the computer from its power source before performing the procedures described here. Failure to disconnect the power before you open the computer can result in personal injury or equipment damage. Refer to your chassis manual for instructions on installing and removing the desktop board.
Intel Desktop Board D945GNT/D945GTP Product Guide Installing and Removing a Processor Instructions on how to install a processor to the desktop board are given below. Installing a Processor CAUTION Before installing or removing a processor, make sure the AC power has been removed by unplugging the power cord from the computer; the standby power LED should not be lit (see Figure 4 on page 24). Failure to do so could damage the processor and the board. To install a processor, follow these instructions: 1.
Installing and Replacing Desktop Board Components 4. Remove the plastic protective socket cover from the load plate (see Figure 9, E). Do not discard the protective socket cover. Always replace the socket cover if the processor is removed from the socket. E OM17228 Figure 9. Remove the Protective Socket Cover 5. Remove the processor from the protective processor cover. Hold the processor only at the edges, being careful not to touch the bottom of the processor (see Figure 10).
Intel Desktop Board D945GNT/D945GTP Product Guide 6. Hold the processor with your thumb and index fingers oriented as shown in Figure 11. Make sure fingers align to the socket cutouts (see Figure 11, F). Align notches (see Figure 11, G) with the socket see (Figure 11, H). Lower the processor straight down without tilting or sliding the processor in the socket. G G H F H F OM17214 Figure 11. Install Processor 7.
Installing and Replacing Desktop Board Components Installing the Processor Fan Heat Sink Desktop board D945GNT/D945GTP has an integrated processor fan heat sink retention mechanism (RM).
Intel Desktop Board D945GNT/D945GTP Product Guide Installing and Removing Memory NOTE To be fully compliant with all applicable Intel SDRAM memory specifications, the boards require DIMMs that support the Serial Presence Detect (SPD) data structure. You can access the PC Serial Presence Detect Specification at: http://www.intel.com/technology/memory/ddr/specs/dda18c32_64_128x72ag_a.
Installing and Replacing Desktop Board Components Three DIMMs Install a matched pair of DIMMs equal in speed and size in DIMM 0 (blue) and DIMM 1 (black) of channel A. Install a DIMM equal in speed and total size of the DIMMs installed in channel A in either DIMM 0 or DIMM 1 of channel B (see Figure 16). Channel A 256 MB, 533 MHz DIMM 0 256 MB, 533 MHz DIMM 1 Channel B 512 MB, 533 MHz DIMM 0 DIMM 1 Figure 16.
Intel Desktop Board D945GNT/D945GTP Product Guide Installing DIMMs NOTE Install memory in the DIMM sockets prior to installing the PCI Express video card to avoid interference with the memory retention mechanism. 1. Observe the precautions in "Before You Begin" on page 27. 2. Turn off all peripheral devices connected to the computer. Turn off the computer and disconnect the AC power cord. 3. Remove the computer’s cover and locate the DIMM sockets (see Figure 17). R Intel (ICH7) OM17617 Figure 17.
Installing and Replacing Desktop Board Components Removing DIMMs To remove a DIMM, follow these steps: 1. Observe the precautions in "Before You Begin" on page 27. 2. Turn off all peripheral devices connected to the computer. Turn off the computer. 3. Remove the AC power cord from the computer. 4. Remove the computer’s cover. 5. Remove the PCI Express card if it interferes with the DIMM clips from being easily opened and closed. 6. Gently spread the retaining clips at each end of the DIMM socket.
Intel Desktop Board D945GNT/D945GTP Product Guide Installing and Removing a PCI Express* x16 Card CAUTION When installing any PCI Express x16 card on the desktop board, ensure that it is fully seated in the PCI Express x16 connector before you power on the system. If the card is not fully seated in the PCI Express connector, an electrical short may result across the PCI Express connector pins.
Installing and Replacing Desktop Board Components Connecting the IDE Cable The IDE cable can connect two drives to the desktop board. The cable supports the ATA-66/100 transfer protocol. Figure 19 shows the correct installation of the cable. NOTES ATA-66/100 compatible cables are backward compatible with drives using slower IDE transfer protocols.
Intel Desktop Board D945GNT/D945GTP Product Guide Connecting the Serial ATA (SATA) Cable The SATA cable (4-conductor) supports the Serial ATA protocol and connects a single drive to the desktop board. Either end of the cable can be connected to the SATA drive or the connector on the board. For correct cable function: 1. Observe the precaution in "Before You Begin" on page 27. 2. Attach the locking cable end to the connector (Figure 20, A) on the board. 3.
Installing and Replacing Desktop Board Components Connecting Internal Headers Before connecting cables to the internal headers, observe the precautions in "Before You Begin" on page 27. Figure 21 shows the location of the internal headers.
Intel Desktop Board D945GNT/D945GTP Product Guide Installing a Front Panel Audio Solution for Intel® High Definition Audio Figure 21, F on page 43 shows the location of the yellow front panel audio header. Table 9 shows the pin assignments for the front panel audio header. Table 9.
Installing and Replacing Desktop Board Components Connecting Hi-Speed USB 2.0 Headers Before connecting the USB 2.0 headers, observe the precautions in "Before You Begin" on page 27. See Figure 21, D on page 43 for the location of the black USB 2.0 headers. Table 11 shows the pin assignments for the headers. Table 11. Hi-Speed USB 2.
Intel Desktop Board D945GNT/D945GTP Product Guide Connecting the Front Panel Header Before connecting the front panel header, observe the precautions in "Before You Begin" on page 27. See Figure 21, C on page 43 for the location of the multi-colored front panel header. Table 13 shows the pin assignments for the front panel header. Table 13.
Installing and Replacing Desktop Board Components Setting Up the Flexible 6-Channel Audio with Jack Re-tasking (Optional) NOTE This section applies only to D945GNT/D945GTP desktop boards with the triple-stack audio connector. After installing the SigmaTel audio driver from the Intel Express Installer driver CD-ROM, the multi-channel audio feature can be enabled. A B C OM15694 Item Description A Rear left/right out or Line In B Front left/right out C Center/LFE (Subwoofer) or Mic In Figure 22.
Intel Desktop Board D945GNT/D945GTP Product Guide Connecting Fan and Power Cables Connecting Fan Cables Figure 23 shows the location of the fan headers. Connect the processor’s fan heat sink cable to the 4-pin processor fan header on the board. Connect chassis fan cables to the 3-pin fan headers. OR 4 3 2 A 1 4 3 2 B 1 3 2 1 A 3 2 1 B OM17621 Figure 23.
Installing and Replacing Desktop Board Components Connecting Power Cables CAUTION Failure to use the appropriate power supply and/or not connecting the 12 V (2x2) power connector to the desktop board may result in damage to the board or the system may not function properly. See Table 5 on page 16 for power supply requirements. Figure 24 shows the location of the power connectors. Intel R 82945 (GMCH) R Intel 82801 (ICH7) 1 Channel A DIMM 0 2 OM17622 Figure 24.
Intel Desktop Board D945GNT/D945GTP Product Guide Other Connectors Figure 25 shows the location of the PCI add-in card, PCI Express 1x, and diskette drive connectors.
Installing and Replacing Desktop Board Components Setting the BIOS Configuration Jumper NOTE Always turn off the power and unplug the power cord from the computer before changing the jumper. Moving the jumper with the power on may result in unreliable computer operation. Figure 26 shows the location of the desktop board’s BIOS configuration jumper. 3 2 1 OM17624 Figure 26. Location of the BIOS Configuration Jumper The three-pin BIOS jumper enables all board configurations to be done in BIOS Setup.
Intel Desktop Board D945GNT/D945GTP Product Guide Clearing Passwords This procedure assumes that the board is installed in the computer and the configuration jumper block is set to normal mode. 1. Observe the precautions in "Before You Begin" on page 27. 2. Turn off all peripheral devices connected to the computer. Turn off the computer. Disconnect the computer’s power cord from the AC power source (wall outlet or power adapter). 3. Remove the computer cover. 4.
Installing and Replacing Desktop Board Components Replacing the Battery A coin-cell battery (CR2032) powers the real-time clock and CMOS memory. When the computer is not plugged into a wall socket, the battery has an estimated life of three years. When the computer is plugged in, the standby current from the power supply extends the life of the battery. The clock is accurate to ± 13 minutes/year at 25 ºC with 3.3 VSB applied.
Intel Desktop Board D945GNT/D945GTP Product Guide AVVERTIMENTO Esiste il pericolo di un esplosione se la pila non viene sostituita in modo corretto. Utilizzare solo pile uguali o di tipo equivalente a quelle consigliate dal produttore. Per disfarsi delle pile usate, seguire le istruzioni del produttore. PRECAUCIÓN Existe peligro de explosión si la pila no se cambia de forma adecuada. Utilice solamente pilas iguales o del mismo tipo que las recomendadas por el fabricante del equipo.
Installing and Replacing Desktop Board Components AWAS Risiko letupan wujud jika bateri digantikan dengan jenis yang tidak betul. Bateri sepatutnya dikitar semula jika boleh. Pelupusan bateri terpakai mestilah mematuhi peraturan alam sekitar tempatan. OSTRZEŻENIE Istnieje niebezpieczeństwo wybuchu w przypadku zastosowania niewłaściwego typu baterii. Zużyte baterie należy w miarę możliwości utylizować zgodnie z odpowiednimi przepisami ochrony środowiska.
Intel Desktop Board D945GNT/D945GTP Product Guide OСТОРОГА Використовуйте батареї правильного типу, інакше існуватиме ризик вибуху. Якщо можливо, використані батареї слід утилізувати. Утилізація використаних батарей має бути виконана згідно місцевих норм, що регулюють охорону довкілля.
Installing and Replacing Desktop Board Components To replace the battery, follow these steps: 1. Observe the precautions in "Before You Begin" (see page 27). 2. Turn off all peripheral devices connected to the computer. Disconnect the computer’s power cord from the AC power source (wall outlet or power adapter). 3. Remove the computer cover. 4. Locate the battery on the board (see Figure 27). 5. With a medium flat-bladed screwdriver, gently pry the battery free from its connector.
Intel Desktop Board D945GNT/D945GTP Product Guide 58
3 Updating the BIOS The BIOS Setup program can be used to view and change the BIOS settings for the computer. The BIOS Setup program is accessed by pressing the key after the Power-On Self-Test (POST) memory test begins and before the operating system boot begins. F2 OM17050 Figure 28. F2 Key This chapter tells you how to update the BIOS by either using the Intel Express BIOS Update utility or the Iflash Memory Update utility, and how to recover the BIOS if an update fails.
Intel Desktop Board D945GNT/D945GTP Product Guide Updating the BIOS with the Iflash Memory Update Utility With the Iflash BIOS update utility you can update the system BIOS from a floppy disk or other bootable media. The utility available from the Web provides a simple method for creating a bootable flash memory update floppy that will automatically update your BIOS. Obtaining the BIOS Update File You can update to a new version of the BIOS by using the BIOS update file.
Updating the BIOS Recovering the BIOS It is unlikely that anything will interrupt the BIOS update; however, if an interruption occurs, the BIOS could be damaged. The following steps explain how to recover the BIOS if an update fails. The following procedure uses recovery mode for the Setup program. See page 51 for more information on Setup modes. NOTE Because of the small amount of code available in the boot block area, there is no video support.
Intel Desktop Board D945GNT/D945GTP Product Guide 62
4 Configuring for RAID (Intel® Matrix Storage Technology) - Optional Requires Microsoft Windows* XP or 2000 and SATA Hard Drive(s) Configuring the BIOS for Intel Matrix Storage Technology 1. Assemble your system and attach two or more SATA hard drives. 2. Enter system BIOS Setup by pressing the key after the Power-On-Self-Test (POST) memory tests begin. 3. Go to Advanced Drive Configuration Configure SATA as; ensure RAID is selected. 4. Then save your settings by pressing .
Intel Desktop Board D945GNT/D945GTP Product Guide Loading the Intel Matrix Storage Technology RAID Drivers and Software 1. Begin Windows Setup by booting from the Windows installation CD. 2. At the beginning of Windows Setup, press to install a third-party SCSI or RAID driver. When prompted, insert the floppy disk labeled RAID Driver. Install the Intel 82801GR SATA RAID Controller driver. 3. Finish the Windows installation and install all necessary drivers. 4.
A Error Messages and Indicators Desktop board D945GNT/D945GTP reports POST errors in two ways: • By sounding a beep code • By displaying an error message on the monitor BIOS Beep Codes The BIOS also issues a beep code (one long tone followed by two short tones) during POST if the video configuration fails (a faulty video card or no card installed) or if an external ROM module does not properly checksum to zero. Table 15 lists the BIOS codes. Table 15.
Intel Desktop Board D945GNT/D945GTP Product Guide 66
B Regulatory Compliance This appendix contains the following regulatory compliance information for desktop board D945GNT/D945GTP: • • • • • Safety regulations European Union Declaration of Conformity statement Product Ecology statements Electromagnetic Compatibility (EMC) regulations Product certification markings Safety Regulations Desktop board D945GNT/D945GTP complies with the safety regulations stated in Table 17 when correctly installed in a compatible host system. Table 17.
Intel Desktop Board D945GNT/D945GTP Product Guide Čeština Tento výrobek odpovídá požadavkům evropských směrnic 89/336/EEC a 73/23/EEC. Dansk Dette produkt er i overensstemmelse med det europæiske direktiv 89/336/EEC & 73/23/EEC. Dutch Dit product is in navolging van de bepalingen van Europees Directief 89/336/EEC & 73/23/EEC. Eesti Antud toode vastab Euroopa direktiivides 89/336/EEC ja 73/23/EEC kehtestatud nõuetele. Suomi Tämä tuote noudattaa EU-direktiivin 89/336/EEC & 73/23/EEC määräyksiä.
Regulatory Compliance Product Ecology Statements The following information is provided to address worldwide product ecology concerns and regulations. Recycling Considerations As part of its commitment to environmental responsibility, Intel has implemented the Intel Product Recycling Program to allow retail consumers of Intel’s branded products to return used products to select locations for proper recycling. Please consult the http://www.intel.com/intel/other/ehs/product_ecology/Recycling_Program.
Intel Desktop Board D945GNT/D945GTP Product Guide Français Dans le cadre de son engagement pour la protection de l'environnement, Intel a mis en œuvre le programme Intel Product Recycling Program (Programme de recyclage des produits Intel) pour permettre aux consommateurs de produits Intel de recycler les produits usés en les retournant à des adresses spécifiées. Visitez la page Web http://www.intel.com/intel/other/ehs/product_ecology/Recycling_Program.
Regulatory Compliance Türkçe Intel, çevre sorumluluğuna bağımlılığının bir parçası olarak, perakende tüketicilerin Intel markalı kullanılmış ürünlerini belirlenmiş merkezlere iade edip uygun şekilde geri dönüştürmesini amaçlayan Intel Ürünleri Geri Dönüşüm Programı’nı uygulamaya koymuştur. Bu programın ürün kapsamı, ürün iade merkezleri, nakliye talimatları, kayıtlar ve şartlar v.s dahil bütün ayrıntılarını ögrenmek için lütfen http://www.intel.com/intel/other/ehs/product_ecology/Recycling_Program.
Intel Desktop Board D945GNT/D945GTP Product Guide EMC Regulations Desktop board D945GNT/D945GTP complies with the EMC regulations stated in Table 19 when correctly installed in a compatible host system. Table 19. 72 EMC Regulations Regulation Title FCC Class B Title 47 of the Code of Federal Regulations, Parts 2 and 15, Subpart B, Radio Frequency Devices. (USA) ICES-003 (Class B) Interference-Causing Equipment Standard, Digital Apparatus.
Regulatory Compliance Japanese Kanji statement translation: This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual. Korean Class B statement translation: This is household equipment that is certified to comply with EMC requirements.
Intel Desktop Board D945GNT/D945GTP Product Guide Product Certification Markings (Board Level) Desktop board D945GNT/D945GTP has the product certification markings shown in Table 20: Table 20. Product Certification Markings Description Mark UL joint US/Canada Recognized Component mark. Includes adjacent UL file number for Intel desktop boards: E210882. FCC Declaration of Conformity logo mark for Class B equipment. Includes Intel name and D945GNT or D945GTP model designation. CE mark.
