VZ-IP-PVMN SERIES 23", 27" & 32" IP PUBLIC VIEW MONITOR IP-PVM N USER MANUAL Please read this manual thoroughly before use, and keep it handy for future reference.
CONTENTS Safety Instruction ....................................................................................................................................................................................... 3 1. Mark Indication & Substance ....................................................................................................................................................... 4 2. Warning .................................................................................................
SAFETY INSTRUCTION Important Safety Instruction 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Read all warnings. Follow all instructions to ensure longevity of monitor. Do not place the monitor near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers,stoves, or other heat generating devices.
SAFETY INSTRUCTION Important Safety Instruction Mark Indication and Substance CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol is intended to alert the user to the presence of uninsulated & dangerous voltage within the monitor’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
SAFETY INSTRUCTION Important Safety Instruction Caution • • • • • • • • • • • • • If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth. Make sure to unplug the power cord before cleaning the monitor. Make sure to leave a gap between monitor and wall. Do not drop the monitor when moving it. Place your monitor in a location with low humidity and minimum dust.
FCC RF INTERFERENCE STATEMENT Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
WIRING WIRING (DC 24V input only) 1. On the back of the monitor, loosen the thumb screws and lower the access panel. 2. Attach the leads from the power supply (supplied) to the left and right connectors. WARNING: Do not connect a ground to the center post. Please be careful of voltage polarity. 3. When finished, secure the access panel. Table A shows the recommended maximum wiring distances (transformer to load), and are calculated with a 10-percent voltage drop.
INSTALLATION Installation Tools The following tools may be required depending on your installation. Electronic Stud Finder Pencil Protective Eye-wear Level Phillips Screwdriver Assembly Components - provided Your ViewZ monitor is shipped with all proper installation hardware and components. If there are parts missing and/or damaged, please stop the installation and contact ViewZ USA at (888)-998-4399. V.1.9.
CONNECT EXTERNAL EQUIPMENTS Interface Input Ports The following image is the description of interface input ports q w e rty 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. u i o a sd HDMI IN AV ( BNC ) IN VGA (15 Pin D-Sub) IN AUDIO IN / OUT CAMERA CVBS OUT CAMERA IP(Ethernet) OUT (Optional) Media Player HDMI OUT (Optional) Media Player USB (Optional) Media Player SD Card AC 110V IN DC 24V IN DC 12V OUT User Manual Visit the ViewZ USA website at https://www.viewzusa.
REMOTE FUNCTION Remote Controller Remote Controller 1. Power 2. Source - Select Input Source 3. Mute - Turn off the sound 4. Menu - Enter / Exit OSD 5. Exit - Exit OSD with saving current value 6. Left & Right ◄(VOL)►, Up & Down ▲▼ 7. Enter - Select current setting value on Input source 8. PIP - Launch the PIP (Picture In Picture) mode 9. SWAP - Swap the main & sub on PIP 10. P.POS - Change the sub picture position on PIP 11. P.Size - Change the main & sub picture size on PIP 12. S.Sat - Not working 13.
CONTROL AND FUNCTION On Monitor, Front Area q w e r 1. Built-in Camera / Motion Detection 4. Recording Indicator LED The monitor will display the built-in camera's video User can choose a blinking LED color - red, blue, Built-in camera has the motion detection function purple and no color. 2. IR Sensor Sensor for the remote controller 3. LED Indicator Green color: monitor on Red color : monitor off User Manual Visit the ViewZ USA website at https://www.viewzusa.
CONTROL AND FUNCTION On Monitor, Button Control q w e r t 1. Source To select an input source 2. Menu To enter or exit the OSD / Select a menu on OSD 3. Left & Right ◄ (VOL) ► To change the value on the selected menu 4. Up & Down ▲ ▼ To switch a menu on OSD 5. Power To turn the monitor power on / off Monitor Button Function All picture, sound settings and setup can be adjusted in OSD (On Screen Display) menu. To adjust the OSD screen: 1. Press the MENU button to enter the OSD MENU 2.
CONTROL AND FUNCTION Select Input Source VGA HDMI CAMERA AV MEDIA Press 'SOURCE' button on monitor or 'INPUT' button on remote controller Press ▲ / ▼ button to change input source and then press ◄ / ► button to select input source on monitor Press ▲ / ▼ button to change input source and then press ◄ / ► button or Enter to select input source on remote controller Volume Press◄ / ► buttons to adjust volume on monitor Press◄ / ► buttons to adjust volume on remote controller Detect Source Signal Message If
CONTROL AND FUNCTION Picture FUNCTION ▲/▼ MOVE ◄/► SELECT(ADJUST) MENU RETURN VALUE CONTRAST Adjust the contrast 0 ~ 100 BRIGHTNESS Adjust the brightness 0 ~ 100 HUE 1) Adjust the hue 0 ~ 100 SATURATION Adjust the color saturation 0 ~ 100 SHARPNESS Adjust the sharpness 0 ~ 100 COLOR TEMP Adjust the color setting See table below ASPECT RATIO Adjust the video format See table below PICTURE MODE Adjust the image color setting See table below 1) Only available in Composite ( video ) i
CONTROL AND FUNCTION Sound ▲/▼ MOVE ◄/► SELECT(ADJUST) MENU RETURN FUNCTION VALUE VOLUME Adjusts the volume 0 ~ 100 BALANCE Adjusts the balance 0 ~ 100 SOUND MODE Selects one of the presets LOUDNESS Adjusts preset sound mode BASS Adjusts the bass level MUTE Mutes the sound User Manual USER / MUSIC / MOVIE / STANDARD MODE 1 / MODE 2/ MODE 3 / MODE 4 / OFF Visit the ViewZ USA website at https://www.viewzusa.
CONTROL AND FUNCTION System - OSD SETUP ▲/▼ MOVE ◄/► SELECT(ADJUST) MENU RETURN FUNCTION OSD LANGUAGE Sets the language of the OSD menu VALUE English, Spanish, French Russian, Portuguese 16 OSD DURATION Sets the OSD display time RESTORE DEFAULT Resets the monitor settings to the factory default Visit the ViewZ USA website at https://www.viewzusa.
CONTROL AND FUNCTION Advance - Adjust Recording Indicator Color / Recording Text ▲/▼ MOVE ◄/► SELECT(ADJUST) MENU RETURN RECORDING TEXT Option Window FUNCTION RECORDING INDICATOR Sets the color of recording indicator LED RECORDING TEXT VALUE OFF / RED / BLUE / PURPLE See table below MOTION DETECTION See table on page 17 AUTO SWITCHING See table on page 18 FUNCTION VALUE RECORDING TEXT Enables the recording text OFF / ON TEXT BLINK Sets the blinking text interval time TEXT SIZE Adjusts the siz
CONTROL AND FUNCTION Advance - Adjust Motion Detection ▲/▼ MOVE ◄/► SELECT(ADJUST) MENU RETURN MOTION DETECTION Option Window FUNCTION VALUE DETECTION ENABLE Enables the MOTION DETECTION function OFF / ON DETECTION INPUT Selects the input source for Motion Detection CAMERA / AV / MEDIA / VGA / HDMI DETECTION TIME Adjusts the time to display the swapped image 3 ~ 100 sec / video which is trigged by motion detection.
CONTROL AND FUNCTION Advance - Adjust Auto Switching ▲/▼ MOVE ◄/► SELECT(ADJUST) MENU RETURN AUTO SWITCHING Option Window FUNCTION AUTO SWITCHING Enables the AUTO SWITCHING function TIME Adjusts the time which the monitor displays VALUE OFF / ON 3 ~ 100 sec one input source before switching to the other * Only selected two input sources can be displayed VGA Sets the VGA input source as the switching OFF / ON display source HDMI Sets the HDMI input source as the switching OFF / ON display sourc
CONTROL AND FUNCTION PIP VALUE FUNCTION PIP Selects PIP or OFF See table below SUB SOURCE Selects PIP input source See table below PIP SIZE Adjusts PIP window size See table below PIP-POSITION Adjusts PIP position See table below SOUND SELECT Selects sound source input SWAP Swaps the main display MAIN, SUB ▲/▼ MOVE ◄/► SELECT(ADJUST) MENU RETURN PIP OFF PIP (Picture in Picture) PIP / PBP function off Separates the screen into two parts.
MOUNTING GUIDE Wall Mounting (Optional) VZ-PVM monitors are suitable for VESA wall mount (not included). M4 x L10 screws for VZ-PVM-I2B3N / I2W3N (23" - 100x100) M4 x L10 screws for VZ-PVM-I3B3N / I3W3N (27" - 100x100) M6 x L8 screws for VZ-PVM-I2B3N / I2W3N (23" - 200x200) VZ-PVM-I3B3N / I3W3N (23" - 200x200) VZ-PVM-I4B3N / I4W3N (32") 1. VZ-PVM-I2B3N/I2W3N, VZ-PVM-I3B3N/I3W3N : VESA WALL MOUNT 100mm x 100mm, 200mm x 200mm 2.
SPECIFICATION Model No. Size & Type LCD VZ-PVM-I2B3N / I2W3N VZ-PVM-I3B3N / I3W3N VZ-PVM-I4B3N / I4W3N 23.6" 27" 32" Panel Type 23.6'' LED Backlit Monitor 27'' LED Backlit Monitor 32'' LED Backlit Monitor Pixel Pitch 0.2715 (H) x 0.2715 (V) mm 0.31125 (H) x 0.31125 (V) mm 0.36375 (H) x 0.36375 (V) mm Brightness 250 cd/m² 300 cd/m² 450 cd/m² Contrast Ratio 3000 : 1(Typ.) 3000 : 1(Typ.) 1200 : 1(Typ.) Viewing Angle R/L : 89°/ 89° U/D : 89°/ 89° Display Color 16.
SPECIFICATION Camera Specification Parameters Production Information Main Chipset Camera Lens External interface Video Network WEB application User Manual Description Product Name Encode Chipset Sensor Resolution Video System Product Name Digital Zoom Minimum illumination Day & Night Mode Removable Optical Filter Electronic Shutter Speed Gain Control White Balance Wide Dynamic Range (WDR) BLC Highlight Compensation Lens Type Focal Length of the Lens Auto Iris Network Interface CVBS Output Reset But
TROUBLESHOOTING GUIDE - Check the following before calling for service. - If the same problems continue after checking, contact the reseller you purchased the monitor from.
TERMS OF WARRANTY / RMA - The warranty period for this monitor is 3 years. The warranty will be voided for the scenarios listed below. - You can also download the manual and information at VIEWZ web site: VIEWZUSA.
NOTE 26 Visit the ViewZ USA website at https://www.viewzusa.
WARRANTY ViewZ USA LIMITED 3 YEAR WARRANTY What and Who is Covered by this Limited Warranty and for How Long ViewZ USA warrants this product to be free from defects in material and workmanship for 3 years to the original owner of this product. The limited warranty is valid only for the original purchaser of the product. What ViewZ USA Will Do At the sole discretion of ViewZ USA, ViewZ USA will repair or replace any product or product part that is defective.
