VZ-IP-PVMN SERIES 10" IP PUBLIC VIEW MONITOR IP-PVM N USER MANUAL Please read this manual thoroughly before use, and keep it handy for future reference.
CONTENTS Safety Instruction ....................................................................................................................................................................................... 3 1. Mark Indication & Substance ....................................................................................................................................................... 4 2. Warning .................................................................................................
SAFETY INSTRUCTION Important Safety Instruction 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Read all warnings. Follow all instructions to ensure longevity of monitor. Do not place the monitor near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers,stoves, or other heat generating devices.
SAFETY INSTRUCTION Important Safety Instruction Mark Indication and Substance CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol is intended to alert the user to the presence of uninsulated & dangerous voltage within the monitor’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
SAFETY INSTRUCTION Important Safety Instruction Caution • • • • • • • • • • • • • If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth. Make sure to unplug the power cord before cleaning the monitor. Make sure to leave a gap between monitor and wall. Do not drop the monitor when moving it. Place your monitor in a location with low humidity and minimum dust.
FCC RF INTERFERENCE STATEMENT Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
INSTALLATION Installation Tools The following tools may be required depending on your installation. Electronic Stud Finder Pencil Protective Eye-wear Level Phillips Screwdriver Assembly Components - provided Your ViewZ monitor is shipped with all proper installation hardware and components. If there are parts missing and/or damaged, please stop the installation and contact ViewZ USA at (888)-998-4399.
CONNECT EXTERNAL EQUIPMENTS Interface Input Ports The following image is the description of interface input ports q w e 1. SD CARD (MEDIA PLAYER) IN 2. USB (MEDIA PLAYER) IN 3. ETHERNET 10/100 (P.o.E) 8 Visit the ViewZ USA website at https://www.viewzusa.
REMOTE FUNCTION Remote Controller Remote Controller 1. Power 2. Source - Select Input Source 3. Mute - Turn off the sound 4. Menu - Enter / Exit OSD 5. Exit - Exit OSD with saving current value 6. Left & Right ◄(VOL)►, Up & Down ▲▼ 7. Enter - Select current setting value on Input source 8. PIP - Select Picture Mode 9. No Function Media Controller 1. No Function 2. Exit - Exit Media Player Menu 3. Left & Right ◄(VOL)►, Up & Down ▲▼ 4. Enter - Confirm the selection 5. Stop & Play - Freeze the media play 6.
CONTROL AND FUNCTION On Monitor, Front Area q we r 1. Built-in Camera / Motion Detection 3. LED Indicator The monitor will display the built-in camera's video Blue color: monitor on Built-in camera has the motion detection function Red color : monitor off 2. IR Sensor 4. Recording Indicator LED Sensor for the remote controller User can choose a blinking LED color - red, blue, purple and no color. 10 Visit the ViewZ USA website at https://www.viewzusa.
CONTROL AND FUNCTION On Monitor, Button Control i q w 1. Power To turn the monitor power on / off 2. Up & Down ▲ ▼ To switch a menu on OSD 3. Left & Right ◄ (VOL) ► To change the value on the selected menu 4. Menu To enter or exit the OSD / Select a menu on OSD 5. Source To select an input source e rt y u o as 6. Camera Reset 7. Power Loss Buzzer Battery 8. Power Loss Buzzer Off Switch To turn off the buzzer of power loss alarm 9. Power Loss Buzzer 10.
CONTROL AND FUNCTION Select Input Source Input Source CAMERA MEDIA OK Press 'SOURCE' button on monitor or 'INPUT' button on remote controller Press ▲ / ▼ button to change input source and then press ◄ / ► button to select input source on monitor Press ▲ / ▼ button to change input source and then press ◄ / ► button or Enter to select input source on remote controller Volume Press◄ / ► buttons to adjust volume on monitor Press◄ / ► buttons to adjust volume on remote controller Detect Source Signal Message
CONTROL AND FUNCTION Picture ▲/▼ MOVE ◄/► SELECT(ADJUST) MENU RETURN FUNCTION VALUE PICTURE MODE Adjust the image color setting CONTRAST Adjust the contrast 0 ~ 100 BRIGHTNESS Adjust the brightness 0 ~ 100 COLOR Adjust the color 0 ~ 100 TINT Adjust the color chroma 0 ~ 100 SHARPNESS Adjust the sharpness 0 ~ 100 ASPECT RATIO Adjust the video format See table below COLOR TEMP Adjust the color setting See table below See table below PICTURE MODE MOVIE USER PICTURE STANDARD Reduces
CONTROL AND FUNCTION Sound ▲/▼ MOVE ◄/► SELECT(ADJUST) MENU RETURN FUNCTION 14 VOLUME Adjusts the volume MUTE Mutes the sound Visit the ViewZ USA website at https://www.viewzusa.
CONTROL AND FUNCTION System - OSD SETUP ▲/▼ MOVE ◄/► SELECT(ADJUST) MENU RETURN FUNCTION OSD LANGUAGE Sets the language of the OSD menu VALUE English, Spanish, French Russian, Portuguese OSD TIME Sets the OSD display time OSD TRANSPARENT Set up the transparent of the OSD KEY LOCK Enable / disable the monitor button 1) RESTORE DEFAULT 0 ~ 60 sec 1 ~ 10 OFF / ON Resets the monitor settings to the factory default 1) When key lock was enabled and remote controlller lost, please push 'MENU' button
CONTROL AND FUNCTION Advance - Alarm / Adjust Recording Indicator Color ▲/▼ MOVE ◄/► SELECT(ADJUST) MENU RETURN FUNCTION ALARM See table below RECORDING INDICATOR Sets the color of recording indicator LED RECORDING TEXT VALUE OFF / RED / BLUE / PURPLE See table on page 17 MOTION DETECTION See table on page 18 AUTO SWITCHING See table on page 18 PREVENT BURN-IN Set the periodic image retention FUNCTION 16 OFF / ON VALUE VIDEO OBSTRUCTION Set the alarm of PVM's camera block OFF / ON VIDEO LOSS
CONTROL AND FUNCTION Advance - Recording Text ▲/▼ MOVE ◄/► SELECT(ADJUST) MENU RETURN FUNCTION VALUE RECORDING TEXT Enables the recording text OFF / ON BLINK Sets the blinking text interval time SIZE Adjusts the size of text x1/x2/x3 SELECT Selects the preset text TEXT 1 / TEXT 2 / TEXT 3 COLOR Adjusts the color of text OFF / ON / 1 ~ 3 sec RED / GREEN / BLUE / BLACK / WHITE 1) PRESET TEXT - TEXT 1 : Recording / TEXT 2 : Recording in Progress / TEXT 3 : Surveillance in Progress User Manu
CONTROL AND FUNCTION Advance - Adjust Motion Detection ▲/▼ MOVE ◄/► SELECT(ADJUST) MENU RETURN FUNCTION VALUE MOTION DETECTION Enables the MOTION DETECTION function INPUT Selects the input source for Motion Detection TIME Adjusts the time to display the swapped image OFF / ON CAMERA / MEDIA 3 ~ 100 sec / video which is trigged by motion detection. If user selects '10', the monitor will keep showing the swapped image/videos for 10 seconds whether or not motion detected.
CONTROL AND FUNCTION Advance - Adjust Auto Switching ▲/▼ MOVE ◄/► SELECT(ADJUST) MENU RETURN FUNCTION AUTO SWITCHING Enables the AUTO SWITCHING function TIME Adjusts the time which the monitor displays VALUE OFF / ON 3 ~ 100 sec one input source before switching to the other * Only selected two input sources can be displayed MEDIA Sets the MEDIA input source as the switching OFF / ON display source CAMERA Sets the CAMERA input source as the OFF / ON switching display source User Manual Visit
CONTROL AND FUNCTION Media Card Interface SD Card • Connect USB or SD card 1. Connect USB or SD card devices to USB or SD Card slot located at the back of the PVM • Remove USB or SD card 1. Return to the main menu and press exit 2. Remove the USB & SD card from the slot • Priority of Play 1. SD card content 2. USB content • Caution - when media player activated, the priority of playing media type is; 1. Movie 2. Photo • Caution - The media file should be located in the root location.
CONTROL AND FUNCTION Photo When you select PHOTO on the entry menu of Media play: 1. 2. 3. 4. Press the ENTER button and then press ◄ / ► / ▲ / ▼ buttons to select a image file to display. Press the ENTER button to select photo files to play and then press ►║ button to display the image or slide-show. *Note: If you have more than one video file, selected video files will display one by one. Press ►║ button to pause the slide-show and show only one image file in a non “slide-show” mode.
CONTROL AND FUNCTION Movie When you select MOVIE on the entry menu of Media play: 1. 2. 3. 4. Press the ENTER button and then press ◄ / ► / ▲ / ▼ buttons to select a video file to play. Press the ENTER button to select video files to play and then press ►║ button to play the video files. *Note: If you have more than one movie file, selected movie files will display one by one. Press ►║ button to pause the video file.
MOUNTING GUIDE Wall Mounting (Optional) VZ-PVM monitors are suitable for VESA wall mount (not included). M4 x L8 screws 1. VZ-PVM-I1W4N : VESA WALL MOUNT 75mm x 75mm Attention! VZ-PVM-I1W4N (75x75) : You must use 4 * M4 x L8 screws to assemble this monitor and the wall mount bracket. WARNING ! If user uses screws longer than M4 x L8 mm for 75 x 75 - VZ-PVM-I1W4N it may cause damage to the unit. Please use bolt of correct size and length as instructed.
SPECIFICATION Model No. VZ-PVM-I1W4N Size & Type 10.1" LCD Panel Type 10.1'' LED Backlit Monitor Pixel Pitch 0.1695 (H) x 0.1695 (V) mm Brightness 250 cd/m² Contrast Ratio 700 : 1(Typ.) Viewing Angle R/L : 70°/ 70° U/D : 65°/ 65° Display Color 16.7 Million Colors Response Time 30 ms Resolution 1200 (H) x 800 (V) Case Type Metal Active Display Area 216.96 (H) x 135.60 (V) mm Aspect Ratio 16 : 10 Frequency 31-80.
SPECIFICATION Camera Specification Production Information Main Chipset Camera Lens External interface Parameters Description Product Name Encode Chipset Sensor Resolution Video System Product Name Digital Zoom Minimum illumination Day & Night Mode Removable Optical Filter Electronic Shutter Speed Gain Control White Balance Wide Dynamic Range (WDR) BLC Highlight Compensation Lens Type Focal Length of the Lens Network Interface Reset Button Video Encode 2 MP IP module Hi3516D SONY IMX290 1920 (W) x 108
TROUBLESHOOTING GUIDE - Check the following before calling for service. - If the same problems continue after checking, contact the reseller you purchased the monitor from.
TERMS OF WARRANTY / RMA - The warranty period for this monitor is 3 years. The warranty will be voided for the scenarios listed below. - You can also download the manual and information at VIEWZ web site: VIEWZUSA.
NOTE 28 Visit the ViewZ USA website at https://www.viewzusa.
WARRANTY ViewZ USA LIMITED 3 YEAR WARRANTY What and Who is Covered by this Limited Warranty and for How Long ViewZ USA warrants this product to be free from defects in material and workmanship for 3 years to the original owner of this product. The limited warranty is valid only for the original purchaser of the product. What ViewZ USA Will Do At the sole discretion of ViewZ USA, ViewZ USA will repair or replace any product or product part that is defective.
