VZ-LX SERIES 24", 27", 32" and 42" PROFESSIONAL LED CCTV MONITOR USER MANUAL Please read this manual thoroughly before use, and keep it handy for future reference.
CONTENTS Safety Instruction ....................................................................................................................................................................................... 3 1. Mark Indication & Substance ....................................................................................................................................................... 4 2. Warning .................................................................................................
SAFETY INSTRUCTION Important Safety Instruction 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Read all warnings. Follow all instructions to ensure longevity of monitor. Do not place the monitor near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers,stoves, or other heat generating devices.
SAFETY INSTRUCTION Important Safety Instruction Mark Indication and Substance CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol is intended to alert the user to the presence of uninsulated & dangerous voltage within the monitor’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
SAFETY INSTRUCTION Important Safety Instruction Caution • • • • • • • • • • • • • If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth. Make sure to unplug the power cord before cleaning the monitor. Make sure to leave a gap between monitor and wall. Do not drop the monitor when moving it. Place your monitor in a location with low humidity and a minimum dust.
FCC RF INTERFERENCE STATEMENT Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
INSTALLATION Installation Tools The following tools may be required depending on your installation. Electronic Stud Finder Pencil Protective Eye-wear Level Phillips Screwdriver Assembly Components - provided Your ViewZ monitor is shipped with all proper installation hardware and components. If there are parts missing and/or damaged, please stop the installation and contact ViewZ USA at (888)-998-4399.
CONNECT EXTERNAL EQUIPMENTS Interface Input Ports The following image is the description of interface input ports q e t i oa w ry u 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 8 s d f g AV AUDIO IN ( L / R ) YPbPr AUDIO IN ( L / R ) AV ( BNC ) #1 IN AV ( BNC ) #1 OUT AV ( BNC ) #2 IN AV ( BNC ) #2 OUT YPbPr ( BNC ) IN AV ( BNC ) #3 IN AV ( BNC ) #4 IN AV ( BNC ) #5 IN VGA (15 Pin D-Sub) IN DVI IN HDMI IN AC 110V IN Visit the ViewZ USA website at https://www.viewzusa.
REMOTE FUNCTION Remote Controller (#16) 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Power Picture Freeze Up Left Menu Right Down Mute Input VGA Input Select YPbPr Input Select HDMI Input Select AV Input Select S-Video Input Select - N / A DVI Input Select q w e r t y u i o a s d f g h j Display image, sound and custom settings can be adjusted in OSD (On Screen Display) menu by remote controller. To adjust monitor setting value : 1. 2. 3. 4. 5. 6. 7. 8. 9. 10.
CONTROL AND FUNCTION On Monitor, Button Control q w 1. Source Select an input source 2. Menu Enter or exit the OSD / Select a menu on OSD 3. Left & Right ◄ (VOL) ► Change the value on selected menu 4. Up & Down ▲ ▼ Switch a menu on OSD e r t y u 5. Power Monitor power on / off 6. IR Receiver 7. LED Indicator Green color: monitor on Red color : monitor off Monitor Button Function All picture, sound settings and setup can be adjusted in OSD (On Screen Display) menu. To adjust the OSD screen: 1.
CONTROL AND FUNCTION Select Input Source VGA HDMI DVI AV1 AV2 AV3 AV4 AV5 YPBPR Press 'SOURCE' button on monitor or 'INPUT' button on remote controller Press ▲ / ▼ button to change input source and then press ◄ / ► button to select input source on monitor Press ▲ / ▼ button to change input source and then press ◄ / ► button to select input source on remote controller Volume Press◄ / ► buttons to adjust volume on monitor Press◄ / ► buttons to adjust volume on remote controller Detect Source Signal Messag
CONTROL AND FUNCTION Picture ▲/▼ MOVE ◄/► SELECT(ADJUST) MENU RETURN FUNCTION VALUE BRIGHTNESS Adjust the Brightness 0 ~ 100 CONTRAST Adjust the contrast 0 ~ 100 HUE 1) Adjust the hue 0 ~ 100 SATURATION Adjust the color saturation 0 ~ 100 SHARPNESS Adjust the sharpness 0 ~ 100 COLOR TEMP Adjust the color setting See table below ASPECT RATIO Adjust the video format See table below PICTURE MODE Adjust the image color setting See table below 3D NR Reduce the noise See table below
CONTROL AND FUNCTION Sound Equalizer Option Window ▲/▼ MOVE ◄/► SELECT(ADJUST) MENU RETURN FUNCTION EQUALIZER VALUE Adjust the balance between frequency components within an electronic signal 0 ~ 100 120 Hz / 500 Hz / 1K 5 Hz / 5K Hz / 10K Hz BALANCE Adjust the balance SOUND MODE Select one of the presets LOUDNESS Adjust preset sound mode BASS Adjust the bass level MUTE Mute the sound User Manual -50 ~ +50 USER / MUSIC / MOVIE / STANDARD MODE 1 / MODE 2/ MODE 3 / MODE 4 / OFF Visit the Vie
CONTROL AND FUNCTION System - OSD SETUP ▲/▼ MOVE ◄/► SELECT(ADJUST) MENU RETURN FUNCTION OSD LANGUAGE Set the language of the OSD menu VALUE English, Spanish, French Russian, Portuguese OSD DURATION HDMI - CHANNEL 1) RESTORE DEFAULT Set the OSD display time 0 ~ 60 sec HDMI connection to set for PC PC MODE HDMI connection to set for DVD & PC DVD MODE HDMI connection to set for DVI Channel DVI MODE Reset the monitor settings to the factory default 1) HDMI input support 14 Visit the ViewZ US
CONTROL AND FUNCTION Advance ▲/▼ MOVE ◄/► SELECT(ADJUST) MENU RETURN FUNCTION VALUE H-POSITION 1) Adjust the horizontal picture position 1 ~ 100 V-POSITION Adjust the vertical picture position 1 ~ 100 CLOCK 1) Adjust the number of horizontal picture elements 1 ~ 100 PHASE Adjust the vertical noise of screen image 1 ~ 100 1) 1) SLEEP TIMER Set the time interval for the sleep mode to activate PREVENT BURN-IN Set periodic image retention 0 / 15 / 30 / 45 / 60 sec 1 HR / 2 HR / 4 HR / TEST
CONTROL AND FUNCTION PIP / PBP VALUE FUNCTION MULTI WINDOW Select PIP or PBP option See table below SUB SOURCE Select PIP input source See table below PIP SIZE Adjust PIP window size See table below PIP H-POSITION Adjust PIP horizontal position 0 ~ 100 PIP V-POSITION Adjust PIP vertical position 0 ~ 100 SOUND SELECT Select sound source input MAIN, SUB SWAP Swap the main display ▲/▼ MOVE ◄/► SELECT(ADJUST) MENU RETURN MULTI WINDOW OFF PIP (Picture in Picture) PBP (Picture by Picture) PIP
STAND GUIDE Installing the Monitor Stand To install the monitor stand M6 x L40 screws for VZ-24LX, VZ-27LX, VZ-32LX & VZ-42LX Attention! For VZ-24LX, VZ-27LX, VZ-32LX and VZ-42LX : You must use 4 * M6 x L40 screws to install the monitor stands WARNING ! If screws longer than M6 x L40 mm are used for VZ-24LX, VZ-27LX, VZ-32LX and VZ-42LX, they may cause damage to the unit. Please use bolt of correct size and length as instructed.
MOUNTING GUIDE Wall Mounting (Optional) VZ-LX monitors are suitable for VESA wall mount (not included). M4 x L10 screws for VZ-24LX , VZ-27LX M6 x L8 screws for VZ-32LX M8 x L8 screws for VZ-42LX 1. VZ-24LX, VZ-27LX : VESA WALL MOUNT 75mm x 75mm, 100mm x 100mm 2. VZ-32LX : VESA WALL MOUNT 200mm x 200mm 3. VZ-42LX : VESA WALL MOUNT 300mm x 300mm Attention! VZ-24LX, VZ-27LX : You must use 4 * M4 x L10 screws to assemble this monitor and the wall mount bracket.
SPECIFICATION Model No. VZ-24LX VZ-27LX VZ-32LX VZ-42LX Size & Type 24" 27" 32" 42" Panel Type 24'' LED Backlit Monitor 27'' LED Backlit Monitor 32'' LED Backlit Monitor 42'' LED Backlit Monitor Pixel Pitch (mm) 0.2715 (H) x 0.2715 (V) LCD 0.311 (H) x 0.311 (V) 0.36375 (H) x 0.36375(V) 0.4833 (H) x 0.
TROUBLESHOOTING GUIDE - Check the following before calling for service. - If the same problems continue after checking, contact the reseller you purchased the monitor from.
TERMS OF WARRANTY / RMA - The warranty period for this monitor is 3 years. The warranty will be voided for the scenarios listed below. - You can also download the manual and information of VIEWZ web site: VIEWZUSA.
NOTE 22 Visit the ViewZ USA website at https://www.viewzusa.
WARRANTY ViewZ USA LIMITED 3 YEAR WARRANTY What and Who is Covered by this Limited Warranty and for How Long ViewZ USA warrants this product to be free from defects in material and workmanship for 3 years to the original owner of this product. The limited warranty is valid only for the original purchaser of the product. What ViewZ USA Will Do At the sole discretion of ViewZ USA, ViewZ USA will repair or replace any product or product part that is defective.
