40, 46 & 55-INCH WUXGA NARROW BEZEL TFT-LCD MONITOR INSTRUCTION MANUAL Please read this manual thoroughly before use, and keep it handy for future reference.
………………………………………………………….…… 2~3 …………………………………………………………….......................... 4 ……………………………....................... 5 SAFETY INSTRUCTION CAUTIONS FCC RF INTERFERENCE STATEMENT CONNECTING WITH EXTERNAL EQUIPMENT REMOTE FUNCTIONS …………………………………… 6 ………………………………………………………………… 7 ……………………………………………………….. 8 ~ 16 ………………………………………………….. 17 CONTROLS AND FUNCTIONS AC POWER CONNECTION GUIDE EXTENTENSIONAL IR RECEIVER FOR REMOTE CONTROLLER ..……………. 18 ~ 19 MOUNTING GUIDE ……………………………………………………………………..
Important Safety Instruction 1. Read these instructions. 2. Keep these Instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers,stoves, or other apparatus (including amplifiers) that produce heat. 9.
- The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed no the apparatus. - Minimum distances(e.g. 10cm) around the apparatus for sufficient ventilation. “WARNING – To reduce the risk of fire or electric shock, do not expose the apparatus to rain or moisture.” “The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.
CAUTION The power supply cord is used as the main disconnect device, ensure that the socket-outlet is located/installed near the equipment and is easily accessible. ATTENTIONN Le cordon d`alimentation est utillsé comme interrupteur général. La prise de courant doit être située ou installée à proximité du matériel et être facile d`accès ▶ NEVER REMOVE THE BACK COVER Removal of the back cover should be carried out only by qualified personnel.
NOTE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
A. BACK PANEL CONTROL 1. Extensional Port for Remote Controller Receiver (See page 16 & 17). 2. AV 1 IN. 3. AV 1 OUT. 4. AV 2 IN. 5. AV 2 OUT. 6. S-VIDEO IN. 7. S-VIDEO OUT. 8. AV 1 & SVIDEO AUDIO L/R IN. 9. AV 2 AUDIO L/R IN. 10. Slave RS-232. 11. Master RS-232. 12. HDMI 2 IN. 13. HDMI 1 IN 14. DVI IN. 15. PC VGA IN. 16. PC AUDIO IN. 17. AUDIO OUT. 18. COMPONENT Y/Pb/Pr IN & COMPONENT AUDIO L/R IN. 19. AC IN. 20. AC OUT.
B. REMOTE CONTROLLER(Optional) 1. POWER( ) Turns the power ON or OFF. There will be a few seconds delay before the display appears. 2. SOURCE Selects an input source. 3. AUTO Auto geometry adjustment in the RGB PC source. 4. MUTE Mutes the sound. 5. MENU Activates and exits the On Screen Display. 6. EXIT Exits the On Screen Display. 7. VOL(◀ & ▶) Increases or decreases the level of audio volume. 8. UP/DOWN Moves upwards or downwards in the OSD menu. 9.
C. RIGHT SIDE BUTTON CONTROL 1 & 2. VOL(+) & VOL(-) Adjust the volume and menu settings. 3 & 4. ▲ & ▼ These buttons allow user to enter the sub-menu of the activated function. The up(▲) button is HOLD function and stop the Trigger & Auto switching functions. 5. SOURCE/SELECT Selects an input source. Enters a submenu or accepts your selection in the OSD menu. 6. MENU/EXIT Activates and exits the On Screen Display. This button can also be used to move previous menu or status. 7.
OSD MENU DESCRIPTION All picture, sound settings and setup for the monitor can be adjusted in the OSD menu. (On Screen Display) To adjust the OSD screen: 1. Press the Menu button to enter the OSD menu. 2. Press the ▲/▼ buttons to select the desired option. The selected option is highlighted. 3. Press the ▶ button to enter the submenu for adjusting items. 4. Change the value you wish to adjust by using the ▲/▼ buttons. 5. Press the ◀ button to exit the submenu for adjusting items. 6.
B. Picture/Sound Option Function Value Picture Mode Sets picture mode. See table below Color Tone Sets color tone. See table below Mute Mutes speaker sound. Off or On Volume Adjust the level of audio volume. 0 ~ 100 Size Display picture size. See table below Reduces noise of the picture. On or Off Activates the 3D comb filter. On or Off NR 1) 3D Comb PC 2) 3) See table below. 1) Unavailable in RGB PC, DVI, HDMI1 and HDMI2.
Color Tone Cool Gives the white color a bluish tint. Normal Gives the white color a neutral tint. Warm Gives the white color a reddish tint. User To manually adjust the color tones(Red, Green, and Blue).
C. PIP Option Function Value PIP Activates the PIP feature. Off or On Input Source Selects the input source for the PIP area. See table below PIP Mode PIP Size Position Enables 3 screen size.4:3 side by corner, 4:3 side by 4: 3, PIP, PBP1 or PBP2 and full screen side by side. Selects the size of PIP screen. Size1, Size2 or Size3 Selects the position of PIP screen. Right of Bottom, Left of RB, LB, LT or RT Bottom, Left of Top and Right of Top.
D. Setup Option Function Value Resets the monitor settings to their Reset factory default. English, French, Deutsch, Language Sets the language of the OSD menu. Italian, Spanish, Portuguese or Nederland Changes background of monitor menus. OSD Tone (e.g. input source & information) Displays a blue screen if the monitor Blue Screen receives no signal. Locks all buttons of the monitor. Key Lock1) Note: Use remote controller to unlock.
※ NOTICE: When watching moving images on a computer or a DVR through this monitor using a PCRGB, DVI or HDMI input, you can see blurred images on the edge of icons and pop-up windows but, this is not a defect. The blur may appear on the fixed images such as another icon and pop-up window because the 120Hz feature is focused on fast moving images to enhance the quality of moving image. Auto Switching Option Auto Switching Input Enable Time Function Activates the Auto Switching feature.
Model ID You can control this monitor with “Monitor control” software and “Model ID” functions. Available controls are Turn on, Turn off or change the input source of this monitor. 1. Connect the PC and Monitor(s) with RS-232 Cable. The PC and Monitor(s) have to be turned on. 2. Install the “Monitor Control” software using an enclosed CD. 1) Insert the CD into the PC and open the CD-ROM drive folder. 2) Copy the “Monitor Control” icon and paste it on the screen of the PC. 3) Double click the icon. 3.
2) Monitor Control: Click the “Connect”. - Model ID: Match with the monitor which you want to control. - Monitor Power: Can be “turned on” or “turned off” the monitor. - Source: Can be changed the source of the Monitor e.g.) In this case, you can control the “Model ID No. 0” monitor. ※ For the detail explanation, refer to the enclosed “Monitor Control” CD. 16 ……………………………………………………………………….
※ CAUTION: Do not connect five or more monitors into one wall socket. < Good > < Bad > INSTRUCTION MANUAL ……………………………………………………………………….
1. Extensional Remote Controller Receiver is on the top of the monitor. 18 ……………………………………………………………………….
2. Extensional Remote Controller Receiver is on the bottom of the monitor. INSTRUCTION MANUAL ……………………………………………………………………….
Wall mounting (Optional) The LCD monitors are suitable for VESA standard wall mount (not included in the delivery). M8x12 screws < 40 / 55 inch > M8x12 screws < 46 inch > 1. 40-inch: VESA 400mm x 130mm x 130mm. 2. 46-inch: VESA 600mm x 100mm x 100mm x 100mm. 3. 55-inch: VESA 600mm x 200mm x 200mm. ※ Attention! - 40/55inch : You must use six M8x12 screws to assemble this monitor and the wall mount bracket. - 46inch : You must use eight M8x12 screws to assemble this monitor and the wall mount bracket.
▶ PIN ASSIGNMENTS Pin 1 RED VIDEO 9 2 GREEN VIDEO 10 SIGNAL CABLE DETECT 3 BLUE VIDEO 11 GROUND 12 SDA(for DDC) 4 5 GROUND 13 H-SYNC.(or H+V SYNC.) 6 RED GROUND 14 V-SYNC. 7 GREEN GROUND 15 SCL(for DDC) 8 BLUE GROUND D-SUB ▶ ACCESSORIES 1. Power cord; In & Out. 2. User’s manual. 3. PC cable. 4. RS-232 cable (9pin male to female: direct connection). 5. Monitor Control Software CD. 6. Extensional Remote Controller Receiver cable; Stereo cable. 7. Stereo cable. 8.
This monitor features a power management system to “power down” upon receipt of the VESA DPMS(The display power management signaling) from a VESA DPMS video card. The VESA DPMS-compliant video card performs this signaling system through not sending horizontal, vertical, or sync signal. This monitor enters an appropriate mode through identifying each of the three modes of the signaling system.
40’’ WUXGA 46’’ WUXGA 55’’ WUXGA 40˝ Diagonal AM-TFT 46˝ Diagonal AM-TFT 55˝ Diagonal AM-TFT (Active-Matrix) (Active-Matrix) (Active-Matrix) 0.46125(H) x 0.46125(V) 0.53025(H) x 0.53025(V) 0.63(H) x 0.63(V) TYPE PIXELl PITCH(mm) LCDBRIGHTNESS 700cd/m² (Typical) Type CONTRAST RATIO 3000:1 (Typical) VIEWING ANGLE 178°/178°(H/V) RESPONSE TIME 8msec (G-to-G) RESOLUTION (H x V) FREQUENCY 4000:1(Typical) 1920X1080 @60Hz HORIZONTAL: 31~80KHz / VERTICAL: 56~75Hz VIDEO (2ch input 1.
WEEE Symbols Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life.
P/N : L39ME0281 Rev.
