MODEL: SDI07HY Hybrid Portable Test Monitor User Manual
Precautions • Always handle the unit with care to avoid damaging the LCD display panel. Damage caused by physical shocks is not covered by the product warranty. • Avoid getting fingerprints on the screen. To clean the screen, wipe it with a clean, soft and dry towel, being careful not to damage the LCD display panel. • To reduce the risk of fire or electric shock, do not expose the LCD to rain or moisture. • Do not connect power to the video input/output ports. It will cause a malfunction.
1. Introduction 1-1. Overview The SD107HY is a multi-functional Analogue / HD-SDI / HDMI portable test monitor. It can be used for various purposes, including checking video signals, the cabling status (has a built-in HDSDI / Analogue video signal level meter, adjusting camera angle of view and focusing, supplying power to camera, controlling a speed dome camera and generating color pattern to the monitor. 1-2.
3. Product Parts and Peripheral Device Connection 3-1. Part Names and Functions 1 No. 2 Marking 12V 1 RS-485 2 3 4 HD-SDI INPUT OUTPUT VGA INPUT 7 8 9 10 5 6 7 8 9 10 Function Charge the Built-In Li-Polymer Battery (with Included Charger) or, Supply Power to the Camera (DC12V/500mA) via Power Harness. HDMI Signal Input (Max. 1920 x 1080p60Hz) HD-SDI Signal Input (Max. Resolution : ~3G ) Power Output (When Using Power Over Coax Feature) HD-SDI Signal Output (Loop Through) UXGA Input (Max.
3-1-2. Buttons for Each of the Functions 3 5 HDMI 16:9 1920 X 1080p60 VP : Link Check 16 : 9 1920X1080p60 4 S.LVL: 90% Good FOCUS: 100 / 100 1 1 Level Meter Indicator • S.LVL: Indicates the video signal level of HD-SDI as a percentage. • FOCUS: Indicates the focusing status for HD-SDI video as a percentage. • A. LEVEL: Indicates the brightness level of the video (Amplitude/Sync level) as a percentage • F. LEVEL: Indicates the colour level of the video (Frequency/Burst level) as a percentage.
3 Video Status • Input Mode: HD-SDI, HDMI, VGA, CVBS • Display Mode: 4:3, Full (16:10), 16:9, Zoom1, Zoom2 • Input Resolution: 1920 x 1080p60 , NTSC , PAL 4 Battery Status • There are seven steps indicating battery status. 090% 070% 050% 5 POC (Power Over Coax) device connection indicator. 3-1-2-1. Level Meter Indicator HD-SDI Level Meter • S. Level: Indicates HD-SDI signals as a percentage.
CVBS Level Meter • A. Level: Indicates the brightness of the video (Amplitude/Sync level) as a percentage. The closer to 100%, the better the quality of the video. When the A.Level % is under 100%, it indicates the video signals are decreased and the brightness is reduced. • F. Level: Indicates the colour level of the video (Frequency/Burst level) as a percentage. The closer to 100%, the better the quality of the video colour and the resolution.
3-2. Connection Diagram ※ Only use the included power harness cable when supplying power to a camera. 3-2-1. HD-SDI Input • Connect to HD-SDI camera / output the power to camera using power over coax feature. (Input data bitrate: ~3G) • Outputs power (DC24V) to HD-SDI VP (Video + Power) camera or HD-SDI VP device 3-2-2. HD-SDI Loop through Output • Output the HD-SDI signal input from the HD-SDI camera (Output data bitrate: ~3G) 3-2-3.
3-2-4. PTZ & OSD Control Through RS-485 • Connect to PTZ Receiver and/or Speed Dome Camera as a controller. Also, connect to controller as a PTZ receiver to check if the controller outputs data accurately. ※ Power over coax feature (Video+Power) for HD-SDI & Analogue VP camera and VP transmission devices. • Using the Power Over Coax feature of the Hybrid Test monitor, it’s possible to supply power to VP (Video+power) analogue and HD-SDI cameras via coaxial cable.
• Contrast: To adjust the contrast range (0~100 steps) • Brightness: To adjust the brightness (0 ~ 100 steps) • Hue: To adjust the colour (0 ~ 100 steps) • Saturation: To adjust the chroma (0 ~ 100 steps) • Picture Mode: Standard > Movie > Vivid > User The value of each mode changes automatically • Scale: To adjust the screen ratio (Full > 4:3 > Zoom1 > Zoom2 > 16:9) • Reverse: To reverse the upper and lower sides of the LCD screen. 4-1-1-2.
※ Built-in Protocols: No.
4-1-1-4-1. RS-485 (TX) • Displays the current setting mode at the top of the screen. • Press SET KEY in MULTI WAY KEY selection to select PAN/TILT or ZOOM/FOCUS mode. - RED: P.T.Z MODE - BLUE: OSD MODE • Press the Mode KEY to select CAMERA OSD control mode. • Press the MENU KEY to control CAMERA OSD and press the ESC KEY to exit OSD MENU. • In case of BOX/DOME Camera, hold the ENTER KEY to select the OSD Menu.
4-1-1-4-3.COAX [UP THE COAX] Control • Displays the current setting mode at the top of the screen. • Press the SET KEY in MULTI WAY KEY selection to select PAN/TILT mode or ZOOM/FOCUS mode. - RED: P.T.Z MODE - BLUE: OSD MODE • Press the Mode KEY to select the CAMERA OSD control mode. • Press the MENU KEY to control the CAMERA OSD, and the ESC KEY to exit OSD MENU. For BOX/DOME Cameras, Hold the ENTER KEY to select OSD Menu • Press the EXIT KEY to go to the previous mode.
4-1-1-5. PATTERN SET • Basically outputs the input signals through the Video Out BNC. But if you select “ON” on the CVBS Out in the pattern set menu, the selected pattern is output from the Video Out BNC. • It is possible to select one of ten pattern types. 4-1-1-6. LEVEL METER & FOCUS METER • • • CVBS Level Meter can be ON/OFF. HD-SDI Level Meter can be ON/OFF. HD-SDI Focus Meter can be ON/OFF.
4-1-1-7. SYSTEM SET 16 • To set the System • • • • • Language: KOR / ENG / JAP OSD Dwell Time: To set the time to turn the monitor menu OFF BACK LIGHT: To adjust the brightness of the LED Monitor. Setting Initialisation: To initialise all settings. Version: To display the product Firmware version and the date.
5. Specification SD107HY Hybrid Test Monitor LCD DISPLAY RESOLUTION 1280 X (RGB) X 800 SIZE 6.95 inch (Diagonal) PIXEL PITCH 0.117mm (H) X 0.177mm (V) BRIGHTNESS (cd) Min.:340, Nor.:400 CONTRAST RATIO Viewing Angle Min.:600, Nor.:800 Horizontal 89° Vertical 89° RESPONSE (ms) VIDEO INPUT 11 HDMI ~1080p 60 HD-SDI ~3G PoC Output (DC24V) CVBS XVGA OUTPUT CVBS Indication range for CVBS video signal level RANGE FOR HD-SDI SIGNAL LEVEL CONNECT PORT HDSDI A LEVEL NTSC/PAL 1.
GENIE CCTV LTD. CCTV House, City Park, Watchmead, Welwyn Garden City, Hertfordshire, AL7 ILT Tel: +44 (0) 1707 330541 Fax: +44 (0) 1707 330543 www.geniecctv.com Edition.
