G G G G 20-INCH TFT-LCD PUBLIC VIEW MONITOR Model : LCM-205N INSTRUCTION MANUAL Please read this manual thoroughly before use, and keep it handy for future reference.
CONTENTS SAFETY INSTRUCTION…………………………………………………………………….2 - 3 CAUTIONS ………………………………………..……………………………………………..4 FCC RF INTERFERENCE STATEMENT …………………………………………………….5 CONNECTING WITH EXTERNAL EQUIPMENT…………………………………………… 6 REMOTE FUNCTIONS ……………………………………………………………………….. 7 CONTROLS AND FUNCTIONS…………………………………………………………..8 - 18 D-SUB CONNECTOR PIN ASSIGNMENTS ……………………………………………….19 POWER MANAGEMENT……………………………………………………………………..
SAFETY INSTRUCTION 1. Read all of these instructions. 2. Save these instructions for later use. 3. Follow all warnings and instructions marked on the product. 4. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 5. Do not use this product near water. 6. Do not place this product on an unstable cart, stand or table. The product may fall, causing serious damage to the product. 7.
SAFETY INSTRUCTION Refer all servicing to service personnel. 14. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions. A. When the power cord or plug is damaged or frayed. B. If liquid has been spilled into the product. C. If the product has been exposed to rain or water. D. If the Product does not operate normally when the operating instructions are followed.
CAUTION ඖG NEVER REMOVE THE BACK COVER Removal of the back cover should be carried out only by qualified personnel. ඖG DO NOT USE IN HOSTILE ENVIRONMENTS To prevent shock or fire hazard, do not expose the unit to rain or moisture. This unit is designed to be used in the office or home. Do not subject the unit to vibrations, dust of corrosive gases. ඖG KEEP IN A WELL VENTILATED PLACE Ventilation holes are provided on the cabinet to prevent the temperature from rising.
FCC RF INTERFERENCE STATEMENT NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
G - BACK PANEL CONTROL
CONTROLS AND FUNCTIONS m k G oG A. POWER ON/OFF ( nG lG G pG G j iG hG ) Turns the power ON or OFF. There will be a few seconds delay before the display appears. The power LED (next to the power switch) lights with green when the power is turned ON. The power is turned off by pressing the power switch again and the power LED goes Red. B. POWER LED Power ON: GREEN Stand-by: AMBER Power OFF: RED C. IR Sensor Remote controller sensor. D.
CONTROLS AND FUNCTIONS G. VOLUME ( ൖ ൘ ) Adjust the volume / Adjust menu settings. H. SENSOR Passive infrared sensor detects zone when someone passes I. CAMERA Camera view when someone passes through the detection zone. (Display is always AV1 Mode) J. USB PORT (Option) Connect the USB port to your computer using the USB 2.0 high speed cable (The green LED will light up and your unit is ready to use) K. LED (Card reader) (Option) LED indicators: The Green LED will light up when the unit is ready.
CONTROLS AND FUNCTIONS 1. SELF-TEST DISPLAY When there is no connection at PC, the On Screen Display will show for 3 seconds. Check input Singal 2. OSD MENU DESCRIPTION : Input Source Select PC or AV1, AV2, SVIDEO.C-R(Optional) - If there is no(*note) video when you select C-R(card reader) input, Please move to another Input source *Note) Card reader is not built in.
CONTROLS AND FUNCTIONS : Screen : Brightness Increase or decrease the intensity of the image. : Contrast Increase or decrease the intensity (lightness or dimness) of the image. : H. position (PC Mode Only) Move image horizontally on screen right or left. : V. position (PC Mode Only) Move image vertically on screen up or down. : Clock (PC Mode Only) Adjust the vertical noise of screen image. : Phase (PC Mode Only) Adjust the number of horizontal picture elements.
CONTROLS AND FUNCTIONS : Audio : Volume Adjust audio volume.
: OSD
CONTROLS AND FUNCTIONS G G aGAuto Switch CH: Select “Motion Detect”, “Timer” or “OFF” (Default Mode: OFF) “Motion Detect” : Change from Default CH to Switch CH with PIR sensing Return from Switch CH to Default CH without PIR sensing (Switch time after) Display CH Switch CH Default CH Motion Detect ON Default CHG (Switch time) ଖ The built – in camera is activated at AV1 Mode only “Timer” : Swap between Default CH and Switch CH with selected input source during set “Switch time”.
G G CONTROLS AND FUNCTIONS G G aGDefault CH ( Default Mode : AV2 ) Selector PC or AV1, AV2, SVIDEO.C-R(Optional) G G aGSwitch CH ( Default Mode : AV1 ) Selector PC or AV1, AV2, SVIDEO.
CONTROLS AND FUNCTIONS : Switching Time ( Default time : 60 sec ) Select display time when motion detects and Timer(default CH& Switch CH) - In “Motion Detect” and “Timer” you can control Switchtime - If Motion Detects are continuing within Switchtime at select mode. : Exit : Exit Turn off OSD Menu.
G D-SUB CONNECTOR PIN ASSIGNMENTS ඖG PIN ASSIGNMENTSG Pin 1 RED VIDEO 9 2 GREEN VIDEO 10 SIGNAL CABLE DETECT 3 BLUE VIDEO 11 GROUND 4 GROUND 12 SDA(for DDC) 5 GROUND 13 H-SYNC.(or H=V SYNC) 6 RED GROUND 14 V-SYNC. 7 GREEN GROUND 15 SCL(for DDC) 8 BLUE GROUND ඖG ACCESSORY 1. POWER CORD 2. USER’S MANUAL( With Warranty card ) 3. PC cable 4. Remote Control 5.
POWER MANAGEMENT This monitor features a power management system to “power down” upon receipt of the VESA DPMS (The display power management signaling) from a VESA DPMS video card. The VESA DPMS-compliant video card performs this signaling system through not sending horizontal, vertical, or sync signal. This monitor enters an appropriate mode through identifying each of the three modes of the signaling system.
SPECIFICATIONS 1. Monitor Specification. G ඖG LCD Type Specification 20.1Ԙ͑ Diagonal AM-TFT(Active-Matrix) PANEL Pixel pitch(mm) : 0.21(H) 0.64(V) Pixel Type BRIGHTNESS: 450 d/(Typical) Active Matrix TFT Max Resolution CONTRAST RATIO: 350:1 (Typical) Viewing Angle (Typical) RESPONSE TIME: Tr-12msec, Tf-13msec 640X480 @ 60Hz 89/89/89/89(R/L/T/B) ඖG RESOLUTION(H x V) Pixel Pitch(H/V) 0.64mm x 0.
SPECIFICATONS 2. Camera Specification. Specification G Image Sensor G Resolution G G G G 1/3 -inch CCD 520 TVL S/N Ratio 48 dB Sensitivity 0.25 Lux at F1.0 30IRE Back Light ON / OFF ACK ON / OFF G G High Performance Camera Lens Auto Iris Varifocal Lens 2.8~8.0mm(F0.95~) G 1. AES selector switch G The switch turns on and off the AES function. When an auto Iris lens is G used, be sure to keep this switch at OFF position. G 2.
G SPECIFICATIONS 7. Power indicator (POWER) The LED indicator stays on in green while the camera power is on. 8. Auto Iris lens connector. 9. AC 24V/DC12V power input terminal. 10. Focus Ring : Adjust the focus by operating the focus ring. Loosen the focus tightening knob. Rotate the focus ring to adjust the focus. Tighten the focus tightening knob. 11. Zoom Ring Adjust the appropriate field angle by operating the zoom ring. Loosen the zoom tightening knob.
SPECIFICATIONS 3. Card Reader Specification The card reader is convenient and easy way to share your images with your friends. Card reader function G G G Output interface - BNC composite Video Supporting Memory Card - CF (Compact Flash) - SD (Secure Digital) G G Memory Connector type - IBM micro Drive G - MMC (Multi Media Card) G - CF G - SD/MMC 2 in 1 connector push type G Support file format - JPEG : Display speed G (4.
PIR SENSOR SPECIFICATION 1. Motion Detection Area PVM Unit 15° 15° 3.3M 3.3M 15° 15° 4.7M 4.7M 5.
VESA MOUNT AND CEILING MOUNT HOLE VESA 100X100mm Use the 4ɐ screw G G G G G 26 -------------------------------------------------------------------------------------------INSTRUCTION MANUALG
TROUBLESHOOTING GUIDE TROUBLE No image on display screen TROUBLESHOOTING TIP 1. Check that power cord of the Monitor have been connected securely into wall outlet or grounded extension cable or strip G G G G “Check Input Signal” message on screen 2.Power switch should be in the ON position and LED is lit. 3. Check that the Brightness and/or the Contrast adjustments of the Display have not been turned down to minimums levels. 1.The signal cable should be completely Connected to the video card/computer.
