SXT1811 18.1” SXGA TFT NEMA 4/12 Flat Panel Monitor User’s Guide 301810(B) (was document no. 920A0008 version 1.
Viewtronix reserves the right to make changes in specifications described herein at any time without notice in order to improve design and reliability. Viewtronix does not assume any responsibility for the use of any circuitry described; no circuit patent licenses are implied. Viewtronix assumes no responsibility for damage caused by misuse or improper use of its products.
Table of Contents WARRANTY ..................................................................................................................................................2 Table of Contents ..........................................................................................................................................3 Introduction ....................................................................................................................................................
Introduction The SXT1811 is an 18.1” SXGA (1280 x 1024) TFT industrial flat panel monitor for use in NEMA 4 and NEMA 12 applications. Graphics and text can be displayed on the monitor in up to 16.7 million colors and in the modes listed below. Additionally, PAL NTSC and SECAM video can be displayed either full screen or as a picture in picture overlaid on the PC screen. When the monitor is being driven in modes other than SXGA, it will automatically expand and scale the image to fill all 1280 x 1024 pixels.
Specifications DISPLAY Parameter Specification Display Size 18.1” Diagonal Active Area 14.134” (H) x 11.307” (V) Pixel Format 1280 (H) x 1024 (V) Pixels (1 Pixel = R + G + B Dots) Brightness 200 Nit Typical Back Light Life 50,000 Hrs Typical Contrast Ratio 300:1 Typical Viewing Angle 160 Degrees Vertical and Horizontal Number Colors 16.7 Million PHYSICAL PARAMETER SPECIFICATION Monitor Outside Dimensions 15.70” (H) x 18.51” (W) x 3.
Front and Side View of Monitor 18.51" 3.35" Viewtronix POWER MENU SEL UP SEL DN DEC INC OFF SET UP I O 15.70" ON Installation of Monitor This monitor is intended to be mounted in and used where NEMA 4 and NEMA 12 type enclosures are employed. When mounted properly, the monitor meets or exceeds the sealing requirements set forth in the NEMA 4 and NEMA 12 specifications. The monitor uses “U”-shaped clips and a special gasket to achieve the proper seal.
Cutout Pattern for Monitor PANEL CUT OUT 17.74" +/- .02" 14.93" +/- .
Mode and Image Adjustment Not all video controllers produce exactly the same video output levels or the same timing. The following procedure can be used to select the desired video mode as well as optimize your monitor’s image quality. When adjusting your monitor, the use of video test software such as DisplayMate for Windows by SONERA Technologies can be very beneficial. The SXT1811 automatically adjusts to most incoming video signals.
Use the ⇑ and ß buttons to select phase. Now use ⇐ and Þ buttons to fine-tune the image quality. After completing this adjustment, exit the set up menu by either waiting about five seconds without further button depressions or by hitting the menu button and scrolling until the Exit graphic is highlighted. Once the following graphic is highlighted press the Þ to exit.
Horizontal Position adjust the position of the PIP window horizontally Vertical Position adjust the position of the PIP window vertically Advanced PIP Settings : Brightness adjust the image brightness of the PIP window Contrast adjust the image contrast of the PIP window Sharpness adjust the image sharpness of the PIP window Tint adjust the color of the image of the PIP window Color adjust the tint of the image of the PIP window Video Scaling : Use the ⇑ and (DISPLAYED IN VIDEO MODE ONLY) arr
Direct Access #1: Define the hot key function (⇐ and Þ) for one of the following adjustments : Brightness / Contrast / Volume / Freeze / Zoom / Video Source* Direct Access #2: Define the hot key function (⇑ and ) for one of the following adjustments : Brightness / Contrast / Volume / Freeze / Zoom / Video Source* Display Orientation : Normal / Horizontal Inverse / Vertical Inverse / Inverse Calibrate RGB Gain : Color Calibration (DISPLAYED IN PC MODE ONLY) Load Factory Defaults : Recall factory default sett
VGA Input Connector Pin Out SIGNAL NAME Red Green Blue GND-Digital GND-Red return GND-Green return GND-Blue return GND-Digital Hsync Vsync 15-PIN D-SHELL (FEMALE) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 12
Xycom Automation, Inc. 734-429-4971 • Fax: 734-429-1010 1-800-AT-XYCOM • http://www.xycom.com Northern Europe Sales: +44-1604-790-767 Southern Europe Sales: +39-011-770-53-11 © 2001 Xycom Automation, Inc. All rights reserved. Printed in US. All brand or product names are the property of their respective owners. Specifications may change without notice.
