ViewSonic TM VFD810 Digital Photo Frame - User Guide - Guide de l’utilisateur - Guía del usuario IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in a safe manner, as well as registering your product for future service. Warranty information contained in this User Guide will describe your limited coverage from ViewSonic Corporation, which is also found on our web site at http://www.viewsonic.
Compliance Information FCC Statement This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
1. Do not use the equipment near water. 2. Wipe the machine with a soft and dry cloth. 3. Do not block any vent holes. Please install the product in accordance with the manufacturer’s instructions. 4. Do not use the product on your legs for a long time because it gets hot and you may be burned. 5. Please avoid installing the product in a place where the temperature is above 35°C or lower than 5°C, or in a place that is moist or wet. 6.
Declaration of RoHS Compliance This product has been designed and manufactured in compliance with Directive 2002/95/EC of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below: Substance Lead (Pb) Proposed Maximum Concentration Actual Concentration 0.1% < 0.
Copyright© ViewSonic Corporation, 2010. All rights reserved. ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic Corporation. Disclaimer:ViewSonic Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product.
TABLE OF CONTENTS Introduction.............................................................................................................................................................................................1 Main Features .........................................................................................................................................................................................2 Controls and Connections .................................................................
Introduction Thank you for purchasing this Digital Photo Frame. This Digital Photo Frame is compatible with SD, MMC, and MS memory card formats, which enables you to view digital photo directly from your camera’s memory card. This manual contains important safety information and operation instructions, so please read all the instructions carefully before using the Digital Photo Frame and keeps it for future reference.
Main Features y 8 inch Digital TFT LCD: 800*600 4:3 y Decorative appearance, good quality y Displays digital photos (JPEG) without a computer y Slide show with multiple transition effects y Compatible with SD/MMC/MS memory cards y USB Host for connecting to the USB mass storage ViewSonic 2 VFD810
Controls and Connections ViewSonic 1. SD/MMC/MS -card slot 7. [h] Left/Previous button 2. USB HOST 8. [2] Exit button 3. 5V 1A DC Input socket 9. [M] Menu button; Show tool bar 4. [j] Down button; Rotate a photo counterclockwise 10. [X] Play/Pause/Confirm button 5. [i] Up button; Rotate a photo clockwise 11. On/Off switch 6. [g] Right/Next button 12.
Getting Started Attaching the mount 1. 2. 3. 4. 5. Place the frame on a flat surface with its back facing you. Place the mount carefully in the slot on the back of the frame. Turn the mount counter-clockwise by 45° until it locks. It will now be possible to set the device in the landscape orientation. Turn the mount counter-clockwise by 90° until it locks. It will now be possible to set the device in the portrait orientation.
Inserting Media In order to play photos from a card or a memory stick, insert the card into its respective card slot on the Digital Photo Frame or use the USB port. This Digital Photo Frame is compatible with the following memory cards: • Secure Digital Card (SD) • Multimedia Card (MMC) • Memory Stick (MS) Following is the method of inserting a memory card or attaching a memory stick: 1. Insert the SD/MMC/MS card into the 3-in-1 card slot with the 2. Push a USB memory stick into the USB HOST slot.
Viewing Photos Main menu y When a memory device is inserted into the Digital Photo Frame, the corresponding icon appears on the main menu. y On the main menu, you can select connected source to view photos or change frame settings. Press the [M] button to access the main menu. All connected source, clock and setup icons are displayed. SD/MMC/MS Appears when you insert a SD, MMC or MS card. USB Appears when you inserted a USB flash driver. Setup Customize the settings of Digital Photo Frame.
Playing a slideshow In thumbnail mode, select a photo and then press the [X] button to start slide show from the current photo. The selected photo is displayed on the screen, and there will pop up a hint for button operation. (Note: Do not set hint time to “0” in setup menu, if you want the Digital Photo Frame to display a hint for button operation.) y To pause the slideshow and view a single photo, press the [X] button. To resume the slideshow, press the [X] button again.
Changing Frame Settings The system settings let you customize and configure your Digital Photo Frame. Select the Setup icon on the main menu and press the [X] button. The Setup Menu appears on the screen. 1. To select a setting item, press the [i] or [j] button and then press the [X] button. 2. To change the value, press the [i] or [j] button and then press the [X] button. Or press [2] 3. Press the [M] button to return to the main menu. button to exit.
Frequently Asked Questions 1. Why cannot the Digital Photo Frame display some files from my Flash card or USB device? • Some unpopular memory cards are not compatible with the device. Use a card which matches with the Digital Photo Frame. • The file formats on your card or USB device might not be supported (only JPEG photos are accessible). Provide files with the supported 2. There is a memory card inserted in the Digital Photo Frame, but the device is not able to read the card. What can I do? JPEG.
Specification Display Digital LCD, TFT Panel size: 8 inches Screen aspect ratio: 4:3 Resolution: 800*600 pixels I/O DC in Power Supply AC Adapter (Input: 100~240V AC, 50~60Hz; Output: DC 5V 1A) USB port USB Host 2.0 (High Speed) Supports USB flash media Supported peripheral devices SD™ (Secure Digital Card), MMC™ (MultiMedia Card), MS™ (Memory Stick).
Customer Support For technical support or product service, see the table below or contact your reseller. Note: You will need the product serial number. Country/Region Web Site United States www.viewsonic.com Telephone Toll-Free= 1-800-688-6688 Toll: 1-424-233-2530 Fax: 1-909-468-3757 Toll-Free= 1-866-463-4775 Canada www.viewsonic.
Limited Warranty VIEWSONIC Digital Photo Frame What the warranty covers: ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components.
Mexico Limited Warranty VIEWSONIC Digital Photo Frame What the warranty covers: ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components.
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico: Name, address, of manufacturer and importers: México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas, Col. San Fernando Huixquilucan, Estado de México Tel: (55) 3605-1099 http://www.viewsonic.com/la/soporte/index.htm NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004 Hermosillo: Distribuciones y Servicios Computacionales SA de CV. Calle Juarez 284 local 2 Col. Bugambilias C.
Guerrero Acapulco GS Computación (Grupo Sesicomp) Progreso #6-A, Colo Centro 39300 Acapulco, Guerrero Tel: 744-48-32627 Monterrey: Global Product Services Mar Caribe # 1987, Esquina con Golfo Pérsico Fracc. Bernardo Reyes, CP 64280 Monterrey N.L. México Tel: 8129-5103 E-Mail: aydeem@gps1.com.mx MERIDA: ELECTROSER Av Reforma No. 403Gx39 y 41 Mérida, Yucatán, México CP97000 Tel: (52) 999-925-1916 E-Mail: rrrb@sureste.com Oaxaca, Oax.: CENTRO DE DISTRIBUCION Y SERVICIO, S.A. de C.V. Murguía # 708 P.A., Col.
