Service manual
Table Of Contents
- VP171sb-1.pdf
- VP171 Series Service Manual
- Preface
- Table of Contents
- Chapter 1 Introduction
- Chapter 2 Mechanical Construction
- Chapter 3 Procedure of Disassembly
- Chapter 4 Troubleshooting Procedure
- Chapter 5 RMA Inspection Standard
- Chapter 6 Function Test and Alignment Procedure
- Chapter 7 Firmware Upgrade Procedure
- Chapter 8 DDC Key In Procedure
- Chapter 9 Panel Specification
- Chapter 10 Packing For Shipping
- Chapter 11 Appendix
- VP171sb-1.pdf
- Preface
- Flowchart for Repair
- Table of Contents
- Chapter 1 Introduction
- Chapter 2 Mechanical Construction
- Chapter 3 Procedure of Disassembly
- Chapter 4 Troubleshooting Procedure
- Chapter 5 RMA Inspection Standard
- Chapter 6 Function Test and Alignment Procedure
- Chapter 7 Firmware Upgrade Procedure
- Chapter 8 DDC Key-In Procedure
- Chapter 9 Panel Specification
- Chapter 10 Packing For Shipping
- Chapter 11 Appendix
- Reader's Response
- VP171 -page 11 only.pdf
- VP171 Series Service Manual
- Preface
- Table of Contents
- Chapter 1 Introduction
- Chapter 2 Mechanical Construction
- Chapter 3 Procedure of Disassembly
- Chapter 4 Troubleshooting Procedure
- Chapter 5 RMA Inspection Standard
- Chapter 6 Function Test and Alignment Procedure
- Chapter 7 Firmware Upgrade Procedure
- Chapter 8 DDC Key In Procedure
- Chapter 9 Panel Specification
- Chapter 10 Packing For Shipping
- Chapter 11 Appendix
- VP171 -page 11 only.pdf
- VP171 Series Service Manual
- Preface
- Table of Contents
- Chapter 1 Introduction
- Chapter 2 Mechanical Construction
- Chapter 3 Procedure of Disassembly
- Chapter 4 Troubleshooting Procedure
- Chapter 5 RMA Inspection Standard
- Chapter 6 Function Test and Alignment Procedure
- Chapter 7 Firmware Upgrade Procedure
- Chapter 8 DDC Key In Procedure
- Chapter 9 Panel Specification
- Chapter 10 Packing For Shipping
- Chapter 11 Appendix
- VP171 -page 11 only.pdf
- VP171 Series Service Manual
- Preface
- Table of Contents
- Chapter 1 Introduction
- Chapter 2 Mechanical Construction
- Chapter 3 Procedure of Disassembly
- Chapter 4 Troubleshooting Procedure
- Chapter 5 RMA Inspection Standard
- Chapter 6 Function Test and Alignment Procedure
- Chapter 7 Firmware Upgrade Procedure
- Chapter 8 DDC Key In Procedure
- Chapter 9 Panel Specification
- Chapter 10 Packing For Shipping
- Chapter 11 Appendix

This manual provides the integral information you need to maintain the LCD Monitor, and
the manual is applied to the mode of 1280*1024 resolution and 17 SXGA TFT LCD Monitor.
There are ten topics in this manual, and you can immediately identify problems through the manual.
This manual is for the technicans and people with an electronics background.
Send the product back to the distributor for repairing and do not attempt to do
anything which
is complex or isnt mentioned in the
Troubleshooting.
1-1 The Appropriate Operation
- Turn off the product before cleaning.
- Use only a dry soft cloth when cleaning the LCD panel surface.
- Use a soft cloth moistured with mild detergent to clean the display housing.
- Disconnect the power plug from AC outlet if the product is not used for
a long period of time.
-Do not touch the CRT panel surface with sharp or hard objects.
- Do not use abrasive cleaners, waxes or solvents for your cleaning.
- Do not operate the product under the following conditions :
1.) Extremely hot, cold or humid environment.
2.) Areas susceptible to excessive dust and dirt.
3.) Near any appliance generating a strong magnetic field.
4.) Place in direct sunlight.
ViewSonic Corporation
1
Confidential – Do Not Copy
VP171/b/s
1. Introduction