Service Manual ViewSonic VX700-3 Model No.VLCDS26104-3W 17” Color TFT LCD Display (VX700-3_SM_648 -Rev.
Copyright Copyright ¤ 2002 by ViewSonic Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of ViewSonic Corporation.
Content 1. Engineering Specifications . ...........................................................................................1 1. Scope ..........................................................................................................................1 2. Electrical Characteristics .............................................................................................4 3. Mechanical Characteristics .......................................................................................
6. Mechanical Assembly....................................................................................................59 7. Schematic Daigrams......................................................................................................65 8. PCB LAYOUT..................................................................................................................74 9. Recommended Spare Parts List ...................................................................................76 10.
1. Engineering Specifications 1. Scope The following specifications are applicable to model VX700-3 17 inch color LCD monitor. General Description (VX700-3) LCD Chi-Mei 17.0” SXGA TFT- MVA (premium) Size 17.0 inches diagonal Effective Display Size 337.92 mm X 270.34 mm (typical) Pixel Pitch 0.264 mm X 0.264 mm Resolution 1280 x 1024 dot (SXGA) Brightness 250 cd / m² (typ.), 200 min. Contrast Ratio (500):1(typ.), 350 min.
Display Colors 16,777,216 Preset Timings SXGA/60Hz, 75Hz, XGA/60Hz, 70Hz, 75Hz, 85Hz SVGA/56Hz, 60Hz, 72Hz, 75Hz, 85Hz VGA/60Hz, 72Hz, 75Hz, 85Hz Dos-text/70Hz Synchronization Horizontal Vertical 30 kHz to 83 kHz (automatically) 50 Hz to 75 Hz (automatically) Non-interlaced Max Pixel Rated 135Mhz Resolution Horizontal 1280 dots Vertical 1024 lines Active Display Horizontal 337.92 Area Vertical 270.
Accessories AC power cord-UL 1.8m AC power cord-Schuko 1.8m Analog VGA cable 1.8m DVI-D cable 1.8m Audio cable 1 Micphone cable 1 ViewSonic CD-Wizard 1 Regulatory UL, CSA or cUL, CB Report, CE, FCC-B, DOC-B, TUV/Ergo Standards (which covers ISO13406-2 and MPRIII), TUV/GS, PCT (GOST-R) with 20 Hygienic certificates, PCBC (B Mark), SEMKO, DEMKO, FIMKO, NEMKO, BSMI, VCCI, CCIB/EMC, CCEE, PSB (Singapore Safety), TCO’99, NOM and Argentina IRAM (thru TUV).
2. Electrical Characteristics 2.1 Power Supply 2.1.1 AC Input Input Voltage AC90-264V Frequency 47 / 63Hz Power Consumption: 45 W (typ) on mode Less than 3W power save mode (audio cable not connected) Current Rating 0.7A @ AC100-240V 2.2 LCD LCD Chi-Mei panel(TFT-MVA) Effective display size 337.92 (H) x 270.34 (V) mm (typ) 17.0” / 43 cm diagonal Pixel number 1280 x 1024 pixels Color filter arrangement R.G.B.
Signal Level 75ȍ± 5% Sync Level TTL level Sync Polarity independent 2.3.1.2 Sync On green, Composite Sync 2.3.2 TMDS digital Signals 2.3.2.1 Video type DVI 1.0 compliant 2.3.3 Audio spec. 2.3.3.1 Line input connection 3.5 mm stereo jack x 1 2.3.3.2 Line input signal & impedance 1.3Vrms, 10 kOhm 2.3.3.3 OUTPUT SIGNAL AT SPEAKER TERMINAL 3W @ < 5% DISTORTION 2.3.3.4 Frequency Response 400 Hz – 20 KHz 2.3.3.5 Connector PC99 requirement Audio in Lime Green pantone # 577C 2.3.3.6 Cable length 1.8 m 2.3.3.
3 BLUE 4 GROUND 5 GROUND 6 GROUND 7 GROUND 8 GROUND 9 +5V 10 GROUND 11 N.C 12 SDA 13 H.SYNC 14 V.SYNC 15 SCL 5 1 10 6 15 11 2.3.4.2 Digital TMDS DVI-D Connector 24 pin DVI-D connector pin assignment Pin No. Signal Name Description 1 RX2- TMDS negative differential input, channel 2 2 RX2+ TMDS positive differential input, channel 2 3 GND Logic Ground 4 Reserved 4 Reserved. No connection 5 Reserved 5 Reserved.
8 Reserved 8 Reserved. No connection 9 RX1- TMDS negative differential input, channel 1 10 RX1+ TMDS positive differential input, channel 1 11 GND Logic Ground 12 Reserved 12 Reserved. No connection 13 Reserved 13 Reserved. No connection 14 VCCX Power 15 GND Logic Ground 16 SENS SENSE Pin, Pull High 17 RX0- TMDS negative differential input, channel 0 18 RX0+ TMDS positive differential input, channel 0 19 GND Logic Ground 20 Reserved 20 Reserved.
The factory test input video signal is defined as the following table: Preset No. H.sync Frequency V.sync SYNC POL. Video Mode Frequency H-SYNC V-SYNC 640X350(70) Description MOD [1] 31.468 ±1.0KHz 70.0 ±1.0Hz + - Text mode MOD [2] 31.468 ±1.0KHz 70.0 ±1.0Hz - + 720X400(70) Dos text MOD [3] 31.468 ±1.0KHz 59.94 ±1.0Hz - - 640X480(60) VESA STANDARD MOD [4] 35.01 ±1.0KHz 66.67 ±1.0Hz - - 640X480(66) MAC MOD [5] 37.86 ±1.0KHz 72.81 ±1.
2.6 Display Characteristics 2.6.1 Picture Size Horizontal Width 337.92 mm (typical) Vertical Width 270.34 mm (typical) 2.6.2 Optical Characteristics General qualities: The following data was measured by BM7 of TOPCON Data are panel optical data, for analog signal there are +- 5% tolerance. Item Code Contrast CR Conditions Min. Typ. Max.
Viewing angle: AU = 0°, AR = 0° Warm Up time: minimum 30 minutes Measuring instrument: TOPCOM BM-7 Luminance Meter Measuring distance: 500 mm Measuring angle: 2° 500mm BM-7 2 Degree Notes: (Note 1) Contrast ratio is defined as the following formula. Brightness(Luminance) with all pixels at "white" Brightness with allpixels at "black" Contrast ratio = (Note 2) Viewing angle is measured as follows: 0QTOCN Ǿ ࠑǰ ࠑ ǰ. ǰ . ࠑ : Ǿ. Q ENQEM ;’ Ǿ .
White(TFT OFF) Black(TFT ON) White(TFT OFF) White 100㧑 90㧑 Optical Response 10㧑 0㧑 TF TR (Note 4) Judge points for brightness uniformity.
2.6.3. LCD Panel Mechanical Active Area (mm) 337.92 x 270.34 Pixel pitch (mm) 0.264 (0.088x3) Mass typical (g) 2200 Panel dimensions (WxDxH) mm 383.
2.7 Power Management Unit will enter power saving mode under the following conditions: Power Management condition and status State Signals Power Video LCD LED Horizontal Vertical Video Supply Circuit On Pulses Pulses Active On On On Green Stand-by No Pulses Pulses Blanking Off Off Amber Suspend Pulses No Pulses Off No Pulses No Pulses Complete N/A N/A N/A Off Off 2.
3. Mechanical Characteristics 3.1 Dimensions Net: 410 (W) x 432 (H) x 181 (D) mm Gross: 486 (W) x 525 (H) x 275 (D) mm 3.2 Weight Net: 6.0Kg Gross: 8.7 Kg 3.3 Base Rotation Tilt: up 20 ° / down 5 ° 3.4 Labeling 3.4.1 ID Label (Paste on Rear Cover) Material: Polyester’s Color: Black (same as plastic color) / White (Letter) Size: 50 (W) X 25 (H) mm Location: Rear Back Label Contents: Appendix III 3.4.
3.6 UPC Coding (Code 39 format) Worldwide Model UPC Code: 766907 80253 5 4. Packaging 4.1 Carton Box Dimensions: 486mm (W) x 525mm (H) x 275mm (D) Color: 4-Color printing box Material: BC-FLUTE or Equivalent, double wall 5. Environmental Characteristics 5.1 Operating Conditions Temperature: 0 through + 40° C Humidity: 8% To 80% (39 degree welt bulb) Altitude: 0 – 3,000 Meter 5.
Appendix I Preset Signal Timings H-Video H active Horizontal H front H pulse H back H total V-Video V active Vertical V back V front V pulse V total ! ViewSonic Corporation 28! Confidential – Do Not Copy VX700-3
Analog timing mode table 1 2 3 symb TEXT TEXT VGA ol mode mode H-frequency (kHz) 31.468 31.469 31.468 35.001 37.5 37.862 43.269 V-frequency (Hz) 70.087 70.087 59.941 66.667 75 72.807 85.005 Pixel rate (MHz) 25.175 28.322 25.175 30.240 31.5 31.501 36.
Count num Thd 1024 1056 1040 1056 1048 1152 1344 H- front porch Thf 24 40 56 16 32 32 24 V-sync Tvs 2 4 6 3 3 3 6 V-back porch Tvb 22 23 23 21 27 39 29 Count num Tvd 625 628 666 625 631 667 806 Tvf 1 1 37 1 1 1 3 (H-total) (V-total) V-front porch H-sync.
H-sync. Polarity Negative Negative Positive Positive Positive Positive Negativ e V-sync Polarity Negative Negative Positive Positive Positive Positive Negativ e H-resolution (dots) 1024 1024 1024 1024 1280 1280 1280 V-resolution (lines) 768 768 768 768 1024 1024 720 1 2 3 4 symb TEXT TEXT VGA VGA ol mode mode H-frequency (kHz) 31.468 31.469 31.468 V-frequency (Hz) 70.087 70.087 Pixel rate (MHz) 25.
8 Signal name Symb IBM-851 ol 9 10 11 12 13 14 SVGA SVGA SVGA SVGA XGA XGA 4A H-frequency (kHz) 35.156 37.879 48.077 46.875 53.674 48.363 56.476 V-frequency (Hz) 56.250 60.317 72.188 75.000 85.061 60.004 70.069 Pixel rate (MHz) 36.000 40.000 50.000 49.500 56.250 65.000 75.
H- front porch Thf 24 16 48 48 60 V-sync Tvs 6 3 3 3 5 V-back porch Tvb 29 28 36 38 20 Count num Tvd 806 800 808 1066 750 Tvf 3 1 1 1 5 (V-total) V-front porch ! H-sync.
Appendix II EDID Code Analog 128 BYTES OF EDID CODE: 0 1 2 3 4 5 6 7 8 9 ________________________________________ 0 | 00 FF FF FF FF FF 10 | 11 8F 01 01 01 20 | 0E 22 1B 78 2A 47 06 A5 5C 47 30 | 9C 25 1E 4F 54 BF EF 00 81 80 40 | 01 01 01 01 01 01 01 01 01 01 50 | 01 01 01 01 30 2A 00 98 51 00 60 | 2A 40 30 70 13 00 52 0E 11 00 70 | 00 1E 00 00 00 FF 00 41 32 33 80 | 30 32 30 31 30 30 30 30 31 0A 90 | 00
Appendix III Label Printing ID LABEL Bar Code label/Serial No Label ViewSonic UPC VX700 7 66907 80253 5 MODEL NUMBER: VLCDS26104-3W ViewSonic VX700 SERIAL NUMBER: A23YYWWnnnnn M o d e l N u m b e r : V L CD S 26104-3W S e r i a l N u m b e r : A23YYWWnnnnn (M) ! ViewSonic Corporation 36! Made In China Confidential – Do Not Copy 3 VX700-3
2. Front Panel Function Control Description 1. User control functions Control buttons: - + 1 2 1. Press power button to power on LCD monitor. Led on the power button will turn Green. 2. Press ‘2” button while no OSD will toggle the digital input port and analog input port to display. 3. Press “up” and ‘down” button simultaneously will reset the contrast and brightness to default. 4. Press ‘1” button will enter OSD main menu. 5. Press “volume plus”, “volume minus” can directly adjust the audio volume.
2. OSD operation flow The following steps show how to access the Main Menu, Submenus, and controls within each Submenu. Details on the controls follow the steps listed below. Note: Any OSD setting will only save after user totally exit OSD menu. 1 Press the [1] button to display the Main Menu shown below. 2 Press the [ź] or [Ÿ] button to scroll to the desired menu option. 3 Press the [2] button to select the menu option. 4 Press the [ź] or [Ÿ] button to select submenu option.
Contrast adjusts foreground white level of screen image. [Ÿ] increase contrast, [ź] decease contrast. Shortcut: Before displaying the OnView menu, press the [ź] or [Ÿ] button to adjust. Press button [2] to toggle between brightness and contrast. Brightness adjusts backlight brightness level of screen image. [Ÿ] increase brightness, [ź] decease brightness. Input Select press [ź] or [Ÿ] button to select Input Source. Audio press [ź] or [Ÿ] button to scroll desired menu option.
Audio Volume Balance Bass Treble Mute 1 : Exit 2 : Select Volume increase the volume, decreases the volume, Balance adjusts the proportion of sound coming from each speaker. [ź] directs more of the sound to the left speaker; [Ÿ] directs more of the sound to the right speaker. Bass/Treble adjusts the high (treble) and low (bass) frequency audio output Press [2] button to select bass adjustment. Bass press [ź] or [Ÿ] to adjust bass.
Treble press [ź] or [Ÿ] to adjust treble.
Mute Color Adjust Color Adjust provides four preset color adjustment: 9300K, 6500K, 5400K, 5000K for improved brightness and color saturation. Press button [2] to select the preset color. Press button [ź] or [Ÿ] to fine tune the color response. 9300K—Adds blue to screen image for cooler white (used in most office settings with fluorescent lighting). 6500K—Adds red to screen image for warmer white and richer red. 5400K—Adds green to screen image for a darker color.
Information VLCDS26104-3W A23020101001 Manual Image Adjust H/V Position Press the [2] button to select H-Position or V-Position. H-Position moves screen image left or right. [ź] move screen image to left, [Ÿ] moves screen image to right. Press the [2] button to toggle between H. and V. Position. V-Position moves screen image up or down. [ź] move screen image down, [Ÿ] moves screen image up.
H-Size adjusts the width of screen image. [ź] decreases Width of screen image, [Ÿ] increases width of image. Fine-Tune Sharpness adjusts the clarity of a non-SXGA (1280 x 1024) RGB signal Press [ź] Or [Ÿ] to adjust.
Setup Menu Setup Menu Language Resolution Notice OSD Position OSD Timeout OSD Background Touch Tone 1 : Exit 2 : Select Language Select allows the user to choose from available languages. ᧯խ֮ ១᧯խ֮ ֲء Resolution Notice press the [ź] or [Ÿ] button to select the Enable or Disable the Resolution Notice.
R esolution N otice E nable D isable 1 : E xit 2 : S elect OSD Position press the [2] button to select the OSD H-Position or OSD V-Position. OSD H-Position [ź] moves OSD left; [Ÿ] moves the OSD right. OSD V-Position [ź] moves OSD down; [Ÿ] moves the OSD up. OSD Timeout sets the length of time the OnScreen Display screen is displayed before exiting.
OSD Background ! ViewSonic Corporation 47! Confidential – Do Not Copy VX700-3
Memory Recall Returns the adjustments back to factory settings (only if the LCD Display is operating in a factory preset mode). Press the [2] button to select the Memory Recall menu option. Note: OSD Controls Auto Image Adjust*, Contrast/Brightness, Input Select, Color Adjust [9300K, 6500K(default), 5400, 5000, R, G, B], Information [Mode, Model Number, Serial Number], Manual Image Adjust [H. Size*, H. Position*, V.
3. Circuit Description Function Block 1. Interface Board 1.1 Power Supply (DC/DC Converter) IC100 is a linear regulator that converts a 12V DC input voltage into regulated and stable output voltages of 5V respectively. 1.2 Micro-Controller IC400 (scaler) built-in a micro-controller and extra a flash ROM (IC402---39SF010). It plays a major role in the digital control of the LCD monitor.
Pin 114 controls Inverter enable or disable Pin 113 enable vcc for panel Pin 125 send a HI signal when audio is invalid send a LOW signal when audio is valid pin 5 receive HI signal from IC401 pin 3 to reset pin 1, 4, 39, 43, 46, 47, 125, 206 make key function operate when press key button (receive LOW signal from key button.
circuits derive the required clock frequencies from this single source by default. Other crystal frequencies may be used, but require custom bootstrapping and programming. In lieu of using a crystal oscillator, XTAL can be driven by a single-ended TTL/CMOS input clock (e.g. for testing of the IC) – the TCLK pin should be grounded through a 2.7k pulldown resistor to maintain the correct duty cycle for the clock.
An arbitration mechanism handles the register access requests from the OCM and the system. micro. 1.4 LVDS Transmitter IC500, 501 (SN75LVDS83) FlatLink transmitters contains four 7-bit parallel-load serial-out shift registers, a ҏ clock synthesizer, and five low-voltage differential-signaling (LVDS) line drivers in a single integrated circuit.
multiplied seven times ( ) and then used to unload the data registers in 7-bit slices and serially. The four serial streams and a phase-locked clock (CLKOUT) are then output to LVDS output drivers. The frequency of CLKOUT is the same as the input clock, CLKIN. The SN75LVDS83 requires no external components and little or no control. The data bus appears the same at the input to the transmitter and output of the receiver with the data transmission transparent to the user.
PIN# PIN NAME I/O DESCRIPTION 1 REF - Analog reference voltage(1/2 VDD) 2 VDD - Supply input voltage 3 Agnd - Analog ground 4 Treb_L I Left channel input for treble control 5 Treb_R I Right channel input for treble control 6 RIN I Audio processor right channel input 7 Rout O Gain output and input selector for right channel 8 Louder I Right channel loudness input 9 Rin 3 I Right channel input 3 10 Rin 2 I Right channel input 2 11 Rin 1 I Right channel input 1 12
2.2 Audio amplifier: ICA3 (TDA1517) is an integrated class-B dual output amplifier; it contains two identical amplifier differential input stages. The gain of each amplifier is fixed at 20 dB. Pins 1 and 9 are right and left channel inputs respectively. Pins 4 and 6 are right and left channel outputs which connect to two 8 OHM speakers.
4. Troubleshooting Flow Chart 1. Figure of Waveform FIG1 12V FIG 3. ! FIG2 5V 3.3V FIG 4. 2.5V FIG 5. 32 GRAY SIGNAL INPUT FIG 6.
FIG 7. V-SYNC FIG 9. DISPLAY CLOCK FIG 11. DISPLAY V-SYNC FIG 13. FIG 8. LVDS TX0+ 14.3M CLOCK FIG 10. DISPLAY H-SYNC FIG 12. DISPLAY ENABLE FIG 14.
FIG 15. LVDS CLOCK+ FIG 17. AUDIO SINE SIGNAL IN ! ViewSonic Corporation FIG 16. LVDS CLOCK- FIG 18.
2. No Display on Screen (Screen is black, LED is off) Is screen black? YES NO Check that C202 positive is at 5V. ( FIG 2.
3. No Display on Screen (LED is green) Is the backlight lit? YES NO Check that the cable is fully connected between the Inverter and Interface board Check that the cable is fully connected to CN500 YES NO Check IC500 ,IC501 Pin47 (FIG.13 ) Pin48 (FIG.14 ) Pin39 (FIG.15 ) Pin40 (FIG.16) Pin 2, 4 is low voltage Failure point Failure point The cable is disconnected The cable is disconnected YES Check CN301 pin1 is12V, pin5 is 5V NO YES Check IC502 NO Failure point 1.IC500, IC501 failure 2.
4. No Power On Check that CN100 Pin1 is approximately 12V YES NO Check that F100 output is 12V Failure point 1. Power Board failure 2. Disconnected between CN100 and power board NO YES Failure point Check that FB100, FB101 is 12V YES Check that IC100 pin 2 is about 5V NO F100 failure NO Failure point FB100, FB101 failure Failure point 1.L200 failure 2.D200 failure 3.
5. No Sound (Test signal: 1r.m.s sine waveform) Check that ICA3 Pin 7 is approximately 12V YES NO Check that Q306 Pin 4 is Low voltage Check that ICA1 Pin 3 is approximately 9V YES YES NO Check ICA2 pin11 Pin15 signal is FIG 17. Check ICA1 pin2 is about 12V NO Check Q306 Pin5, 6, 7, 8 is12V Failure point 1.JA1 failure 2.IC400 pin123 failure NO Q306 failure YES YES NO Failure point Check ICA3 pin 4, 6 is FIG18. 1.ICA1 failure 2.
6. Show “No Signal” on screen (Test pattern: 32 gray 1280X1024 60HZ) Check the signal level of R610, R611, R612 is FIG 5. YES NO NO Check the HS and VS is FIG 6. and FIG 7. Failure point 1. The video connector is disconnected 2. Signal cable is disconnected 7. Keypad can not work Check that the cable is fully connected between the Interface board and Key board YES NO Failure point 1. IC400 pin 1, 4, 42, 43, 46, 47, 125,206 failure 2.
5. Adjust Procedure 1. Preparation of manual alignment 1.1 The alignment procedure is performed after unit has been completely assembled and before set inspection. 1.2 Before alignment, set should be burned-in for over 30MIN. 1.3 Measuring equipment used pre-programmed chroma 2226 or equivalent products. Color meter-- Minolta CA210 or equivalent products. 210 mm CA110 1.4 Methods to enter/exit factory mode 1.4.1 Press “2” and “down” key and power on to set the monitor to the burn-in mode. 1.4.
VX700-3 Color Temp Factory 01/10 / 2003 Factory Default Brightness Blacklevel AutoColor Initial EDID CopyColorTemp Gamma Otherwise, follow the procedure described in session 1.4.1 to enter the factory mode again 1.4.3 Under factory mode, press “power” key. the monitor will exit factory mode and enter normal display mode. 1.5 Methods to enter/exit manual color alignment menu Under factory mode, select "Color Temp Manual" from factory OSD menu. It will display the following color temperature adjust menu.
show following menu. Use “2” key to switch r, g, b, driver. “up” or “down” key to adjust the R. G.B value corresponding to the selected item. 2. Color temperature alignment Before manually adjusting color temperature, set OSD contrast 80%, brightness 100% (factory default), enter into factory mode and select “color temp Manual” item. 2.1 9300°k alignment 2.1.1 Use “up” or “down” key to move cursor to 9300 color temperature. Then press “2” key to select 9300 color temperature adjustment. 2.1.
2.2.1 Use “up” or “down” key to move cursor to 6500 color temperature. Then press “2” key to select 6500 color temperature adjustment. 2.2.2 Use “2” to move cursor to r-driver or g-driver or b-driver and then press “up” or “down” key to adjust it to meet following chromaticity spec. 6500 ̓ k ШX = 0.313 ̈́ 0.003, Y = 0.329±0.003 y>= 180cd/m2. 2.2.3 Press “1” to exit 6500 color temperature adjustment and do another color temperature adjustment.
2.4.3 Press “1” to exit 5000 color temperature adjustment and do another color temperature adjustment. The above result R,G,B gain will automatically be saved, when exiting the the factory mode OSD menu. 3. Factory preset setting 3.1 In factory mode OSD main menu select factory default setting. Press “2” to confirm the selection.
6.
ViewSonic Corporation 71! Confidential – Do Not Copy VX700-3
ViewSonic Corporation 72! Confidential – Do Not Copy VX700-3
! ViewSonic Corporation 73! Confidential – Do Not Copy VX700-3
! ViewSonic Corporation 74! Confidential – Do Not Copy VX700-3
Mechanical Parts List Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 VIEWSONIC P/N M-SCW-0824-0696 M-SCW-0814-0692 M-SCW-0824-0620 M-CV-0830-2355 M-CV-0830-2305 M-MS-0808-8160 M-MS-0808-8159 M-SCW-0814-0691 M-CV-0830-2306 M-CV-0830-2315 M-MS-0808-8163 M-MS-0808-8164 C-BC-0302-0479 M-SCW-0824-0697 E-SK-0412-0071 M-SCW-0824-0620 M-SCW-0814-0694 M-CV-0830-2385 PL-FK-0
7.
L17KMW/L18HMW 05AAW LCD MONITOR BLOCK DIAGRAM 2.5V CN601 HD-15 15PINS ANALOG HS VS VGA_SDA VGA_SCL IC603 74F14 12V BACKLIGHT_EN BACKLIGHT_CONTROL RGB I/P IC400 DISPLAY ENGINE GM5120 ADC+DVI+SCALER+MCU CN600 DVI-D INVERTER 3.3V Hsync Vsync 5V 24PINS 3.3V IC500 CN500 LVDS LVDS PANEL 3.
ViewSonic Corporation 67! Confidential – Do Not Copy VX700-3
ViewSonic Corporation 68! Confidential – Do Not Copy VX700-3
ViewSonic Corporation 69! Confidential – Do Not Copy VX700-3
ViewSonic Corporation 70! Confidential – Do Not Copy VX700-3
ViewSonic Corporation 71! Confidential – Do Not Copy VX700-3
ViewSonic Corporation 72! Confidential – Do Not Copy VX700-3
8.
! ViewSonic Corporation 74! Confidential – Do Not Copy VX700-3
! ViewSonic Corporation 75! Confidential – Do Not Copy VX700-3
9.
59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 M-MH-0822-0005 M-MH-0822-0006 M-MH-0822-0006 M-MH-0822-0007 M-CV-0830-2386 M-CV-0830-2387 M-CV-0830-2388 M-MS-0808-8163 M-MS-0808-8164 P-FM-0602-0764 P-FM-0602-0765 M-MS-0808-7741 A-CD-VX700-3 M-WR-0828-0680 M-WR-0828-0681 M-WR-0828-0682 M-WR-0828-0683 M-WR-0828-0684 M-WR-0828-0641 E-SK-0412-0070 E-SK-0412-0071 B-SB-0221-0458 M-MS-0808-7742 M-LCD-0826-0133 B-AC-0215-0038 B-IF-0222-0033 B-KB-0207-0030 B-SB-0221-0450 3460141
10. Complete Parts List VS Model Name: VX700-3 ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 ! 48 49 REFERENCE NO.
50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 PL-PD-0714-0067 PL-PD-0714-0068 M-MS-0808-8155 C-BC-0302-0478 M-CV-0830-2381 M-CV-0830-2382 C-FP-0301-0777 M-CV-0830-2384 M-CV-0830-2385 PL-FK-0709-0114 M-CV-0830-2383 C-BC-0302-0479 M-MS-0808-7739 C-BC-0302-0477 M-MS-0808-8159 M-MH-0822-0002 M-MH-0822-0004 M-MS-0808-8162 ViewSonic Corporation 3221407510 3240659901 3240956800 3240957500 32409598
101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 M-MH-0822-0005 M-MH-0822-0006 M-MH-0822-0007 M-CV-0830-2386 M-CV-0830-2387 M-CV-0830-2388 M-MS-0808-8163 M-MS-0808-8164 P-FM-0602-0764 P-FM-0602-0765 M-MS-0808-7674 P-BX-0601-0786 M-MS-0808-5135 M-MS-0808-7748 PL-SP-0723-0002 M-MS-0808-7741 M-MS-0808-8396 M-MS-0808-7742 A-CD-VX700-3 M-WR-0828-0682 M-WR-
152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 E-R-0405-7041 E-R-0405-7041 E-R-0405-7041 E-R-0405-6684 E-R-0405-6684 E-R-0405-6684 E-R-0405-6684 E-R-0405-6684 E-R-0405-6684 E-R-0405-6684 E-R-0405-6684 E-R-0405-6684 E-R-0405-6684 E-R-0405-6684 E-R-0405-6684 E-R-0405-6684 E-R-0405-6684 E-R-0405-6684 E-R-0405-6684 E-R-0405-6684 E-R-0405-6684 E-R-0405-7054
203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 E-R-0405-7042 E-R-0405-7042 E-R-0405-6687 E-R-0405-6687 E-R-0405-6687 E-R-0405-7058 E-R-0405-7058 E-R-0405-7058 E-R-0405-7043 E-R-0405-6690 E-R-0405-6690 E-R-0405-6690 E-R-0405-6690 E-R-0405-7033 E-R-0405-7033 E-R-0405-7033 E-R-0405-7033 E-R-0405-7033 E-R-0405-7033 E-R-0405-7033 E-R-0405-7033 E-R-0405-703
254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 E-FS-0410-0074 E-C-0404-4857 E-C-0404-4857 E-C-0404-4857 E-C-0404-4856 E-C-0404-4856 E-C-0404-4869 E-C-0404-4869 E-C-0404-4869 E-C-0404-4869 E-C-0404-4869 E-C-0404-4869 E-C-0404-4869 E-C-0404-4869 E-C-0404-4869 E-C-0404-4869 E-C-0404-4869 E-C-0404-4869 E-C-0404-4869 E-C-0404-4869 E-C-0404-4869 ViewSonic
305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 E-C-0404-4869 E-C-0404-4869 E-C-0404-4869 E-C-0404-4869 E-C-0404-4869 E-C-0404-4869 E-C-0404-4869 E-C-0404-4869 E-C-0404-4878 E-C-0404-4878 E-C-0404-4878 E-C-0404-4878 E-C-0404-4878 E-C-0404-4878 E-C-0404-4881 E-C-0404-4881 ViewSonic Corporation 1511454000 1511454000 1511454000 1511454000 1511454000 1511
356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 E-D-0403-2053 E-D-0403-2053 E-D-0403-2053 E-D-0403-2053 E-D-0403-2053 E-D-0403-2053 E-D-0403-2050 E-D-0403-2050 E-D-0403-2050 E-D-0403-2050 E-D-0403-2050 E-D-0403-2050 E-D-0403-2050 ViewSonic Corporation 1552458000 1552458000 1552458000 1552458000 1552458000 1552458000 1552458000 1552458000 1552458000 15
407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 E-Q-0402-1087 E-Q-0402-1087 E-Q-0402-1087 E-Q-0402-1087 E-Q-0402-1087 E-Q-0402-1087 E-Q-0402-1180 E-Q-0402-1180 E-Q-0402-1180 E-Q-0402-1180 E-Q-0402-1180 E-Q-0402-1180 E-Q-0402-1551 E-Q-0402-1552 E-IC-0401-1931 E-IC-0401-1931 E-IC-0401-1932 E-IC-0401-1932 E-IC-0401-2704 E-IC-0401-2687 E-IC-0401-2688 E-I
458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 B-KB-0207-0030 505 M-MS-0808-8179 506 507 508 ViewSonic Corporation 2817123010 2921093612 2921093612 2921093612 2921093612 2921093612 2921093612 2921093612 2921093612 2921093612 2921093612 2921093612 2921093612 2921093612 2921093612 2921093612 2921093612 2921113212 2921113212 2921113212 2921113212 2921113212 2921113212 29
509 510 511 512 513 514 515 516 517 M-WR-0828-0224 518 M-WR-0828-0402 519 B-SB-0221-0450 520 521 522 523 ViewSonic Corporation 3000093900 3000093900 3000093900 3000093900 3000093900 3000093900 3070337934 3122009500 3411000300 4010670000 5600200113 0990601015 2973007402 3072230200 3072230300 SWITCH TACTILE DPST SWITCH TACTILE DPST SWITCH TACTILE DPST SWITCH TACTILE DPST SWITCH TACTILE DPST SWITCH TACTILE DPST WAFER 2.0mm 11P R-ANGLE HOLDER FOR LED NY66 UL94V-2 6* JUMP WIRE BRASS 0.6*7.5*4.0 WIRE CU 0.
*Readers Response* Dear Readers: Thank you in advance for your feedback on our Service Manual,which allows continuous improvement of our products. We would appreciate your completion of the Assessment Matrix below, for return to ViewSonic corporation. Assessment A.
