User guide
Table Of Contents
- PJD6220_Contents_Eng.pdf
- Introduction
- Projector with Lens Cap
- AC Power Cord
- VGA Cable (D-SUB to D-SUB)
- Quick Start Guide
- VGA - Component Adapter
- Using the Product
- Installing the Batteries
- Powering On the Projector:
- Powering Off the Projector:
- 1. Press button to turn off the projector lamp. You will see a message "Power off? Press Power again" appear on the screen.
- 2. Press button again to confirm.
- 3. Disconnect the AC power cord from the electrical outlet and the projector.
- 4. Do not turn on the projector immediately following a power off procedure.
- Adjusting the Projector
- Adjusting the Projector Height
- Adjusting the Projector Zoom and Focus
- Adjusting Projection Image Size
- Menu Operation
- 1. Press the Menu button on the control panel or the MENU button on the remote control to open the OSD menu.
- 2. When OSD is displayed, use p / q to select any feature in the main menu.
- 3. After selecting the desired main menu feature, press u to enter sub-menu for feature setting.
- 4. Adjust the settings with t / u.
- 5. Press the Menu buttonon the control panel or the MENU button on the remote control, the screen will return to the main menu.
- 6. To exit OSD, press the Menu button on the control panel or the MENU button on the remote control again. The OSD menu will close and the projector will automatically save the new settings.
- Maintenance
- Cleaning the Lens
- Cleaning the Projector Housing
- Replacing the Lamp
- 1. Turn off the projector.
- 2. If the projector is installed in a ceiling mount, remove it from the mount.
- 3. Unplug the power cord.
- 4. Loosen the screw in the side of the lamp cover and remove the cover.
- 5. Remove the screws from the lamp module, raise the handle, and lift out the module.
- 6. Insert the new lamp module into the projector and tighten the screws.
- 7. Replace the lamp cover and tighten the screw.
- 8. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.
- 9. Reset the lamp hour. Refer to the “Setting” menu.
- Specifications
- Appendix
- Menu Operation
- Computer:
- Video:
- Start-up problems
- Image problems
ViewSonic 41 PJD6220/PJD6230/PJD6240
Troubleshooting
Refer to the symptoms and measures listed below before sending the projector
forrepairs. If the problem persists, contact your local reseller or service center. Please
refer to "Indicator Messages" as well.
Start-up problems
If no lights turn on:
Be sure that the power cord is securely connected to the projector and the other end
is plugged into an outlet with power.
Press the power button again.
Unplug the power cord and wait for a short while, then plug it in and press the power
button again.
Image problems
If the searching source is displayed:
Press the
Source
button
one or more times to select another active input source.
Be sure the external source is turned on and connected.
For a computer connection, ensure your notebook computer’s external video port is
turned on. Refer to the computer manual.
If the image is out of focus:
Be sure the lens cover is open.
While displaying the on-screen menu, adjust the focus ring. (The image size should
not change; if it does, you are adjusting the zoom, not the focus.)
Check the projection lens to see if it needs cleaning.
If the image is flickering or unstable for a computer connection:
Press the
Resync
button on the control panel
.
Press the Menu button on the control panel or the MENU button on the remote
control, go to Computer Image and adjust Frequency or Tracking.
Remote control problems
If the remote control does not operate:
Be sure nothing is blocking the remote control receiver on the front or back of the
projector. Use the remote control within the effective range.
Aim the remote control at the screen or at the front or back of the projector.
Move the remote control so it is more directly in front of or behind the projector and
not as far to the side.