User guide
Table Of Contents
- PJD5112_UG_ENG.pdf
- VPD-S5500-EN.pdf
- FCC Notice
- Safety Instructions
- Notes on the AC Power Cord
- Powering On the Projector:
- Powering Off the Projector:
- 1. Press button to turn off the projector lamp. You will see a message "Power off? Press Power again" appear on the screen.
- 2. Press button again to confirm.
- 3. Disconnect the AC power cord from the electrical outlet and the projector.
- 4. Do not turn on the projector right after power off.
- Adjusting the Projector
- Adjusting the Projector Height
- Adjusting the Projector Zoom and Focus
- Adjusting Projection Image Size
- Menu Operation
- 1. Press the MENU button to open the OSD menu.
- 2. When OSD is displayed, use p / q to select any feature in the main menu.
- 3. After selecting the desired main menu item, press u to enter sub-menu for feature setting.
- 4. Use p / q to select the desired item and adjust the settings with t / u.
- 5. Press the MENU button, the screen will return to the main menu.
- 6. To exit OSD, Press the MENU button again. The OSD menu will close and the projector will automatically save the new settings.
- Maintenance
- Cleaning the Lens
- Cleaning the Projector Housing
- Cleaning the Filter Cover
- Replacing the Lamp
- 1. Turn off the projector.
- 2. If the projector is installed in a ceiling mount, remove it
- 3. Unplug the power cord.
- 4. Loosen the screw in the side of the lamp cover and remove the cover.
- 5. Remove the screws from the lamp module, raise the handle, and lift out the module.
- 6. Insert the new lamp module into the projector and tighten the screws.
- 7. Replace the lamp cover and tighten the screw.
- 8. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.
- 9. Reset the lamp hour. Refer to the “Setting” menu.
- Specifications
- Appendix
- Menu Operation
- Computer:
- Video:
- Start-up problems
- Image problems
- VPD-S5500-EN-0821.pdf
- FCC Notice
- Safety Instructions
- Notes on the AC Power Cord
- Powering On the Projector:
- Powering Off the Projector:
- 1. Press button to turn off the projector lamp. You will see a message "Power off? Press Power again" appear on the screen.
- 2. Press button again to confirm.
- 3. Disconnect the AC power cord from the electrical outlet and the projector.
- 4. Do not turn on the projector right after power off.
- Adjusting the Projector
- Adjusting the Projector Height
- Adjusting the Projector Zoom and Focus
- Adjusting Projection Image Size
- Menu Operation
- 1. Press the MENU button to open the OSD menu.
- 2. When OSD is displayed, use p / q to select any feature in the main menu.
- 3. After selecting the desired main menu item, press u to enter sub-menu for feature setting.
- 4. Use p / q to select the desired item and adjust the settings with t / u.
- 5. Press the MENU button, the screen will return to the main menu.
- 6. To exit OSD, Press the MENU button again. The OSD menu will close and the projector will automatically save the new settings.
- Maintenance
- Cleaning the Lens
- Cleaning the Projector Housing
- Cleaning the Filter Cover
- Replacing the Lamp
- 1. Turn off the projector.
- 2. If the projector is installed in a ceiling mount, remove it
- 3. Unplug the power cord.
- 4. Loosen the screw in the side of the lamp cover and remove the cover.
- 5. Remove the screws from the lamp module, raise the handle, and lift out the module.
- 6. Insert the new lamp module into the projector and tighten the screws.
- 7. Replace the lamp cover and tighten the screw.
- 8. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.
- 9. Reset the lamp hour. Refer to the “Setting” menu.
- Specifications
- Appendix
- Menu Operation
- Computer:
- Video:
- Start-up problems
- Image problems
- VPD-S5500-EN.pdf
EN-28
Appendix
LED Indicator Messages
LED Type Color Status Meaning
Power LED Blue Solid
The projector is in standby
mode.
Lamp LED Off Off
Temp LED Off Off
Power LED Blue Solid
Powering upLamp LED Off Off
Temp LED Off Off
Power LED Blue Solid
Normal operationLamp LED Off Off
Temp LED Off Off
Power LED Blue Flash
Power-downLamp LED Off Off
Temp LED Off Off
Power LED Blue Solid (Full brightness)
The projector system has some
problems with its fans, so the
projector cannot start up.
Lamp LED Red Solid
Temp LED Red Flash
Power LED Blue Solid (Full brightness)
The lamp is in good condition
and is projecting at maximum
brightness.
Lamp LED Off Off
Temp LED Off Off
Power LED Blue Solid (Full brightness) The lamp has reached its end
of life and must be changed
soon. The lamp will continue to
operate until it fails . Change
the lamp. If the lamp is off, then
the ballast will become
malfunction.
Lamp LED Off Solid
Temp LED Off Solid
Power LED Blue Flash (Full
brightness)
The projector is shutting and
the fan motor is cooling the
lamp for shutdown. Do not
unplug the power cord or turn
the power off before the Lamp
LED changes to flashing. The
fan motor will turn off when the
lamp has cooled.
Lamp LED Red Solid
Temp LED Red Solid
Power LED Blue Solid (Full brightness) Temperature is too high. The
lamp will turn off. The fan motor
is cooling the lamp.
Lamp LED Red Flash
Temp LED Red Off
Power LED Off Off The lamp ignition failed. If
temperature is too high, the
fans will cool the lamp.
Lamp LED Red Solid
Temp LED Red Solid
Downloaded From projector-manual.com Viewsonic Manuals