® ViewSonic PJ758/PJ759/PJ760 LCD Projector - User Guide - Guide de l’utilisateur - Bedienungsanleitung - Guía del usuario - Guida dell’utente - Guia do usuário - Användarhandbok - Käyttöopas - Руководство пользователя - 使用手冊 (繁體) - 使用手冊 (簡體) - 사용자 안내서 Model No. : VS11862/VS11861/VS11822 Downloaded From projector-manual.
Compliance Information FCC Statement This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this unit near water. 6. Clean with a soft, dry cloth. If still not clean, see “Cleaning the Display” in this guide for further instructions. 7. Do not block any ventilation openings. Install the unit in accordance with the manufacturer’s instructions. 8.
Declaration of RoHS Compliance This product has been designed and manufactured in compliance with Directive 2002/95/EC of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below: Proposed Maximum Concentration Actual Concentration Lead (Pb) 0.1% < 0.1% Mercury (Hg) 0.
Copyright Information © © Copyright ViewSonic Corporation, 2007. All rights reserved. Macintosh and Power Macintosh are registered trademarks of Apple Computer, Inc. Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries. ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic Corporation. VESA is a registered trademark of the Video Electronics Standards Association.
Projector PJ758/PJ759/PJ760 User's Manual (detailed) Operating Guide VIDEO RGB ASPECT (1) Projector (2) Remote control with two AA batteries (3) Power cord (4) RGB cable (5) Audio/Video cable (6) Soft case (7) Quick Start Guide and ViewSonic Wizard CD (8) Lens cover and Strap MAGNIFY ON OFF SEARCH AUTO HOME PAGE UP END PAGE DOWN FREEZE BLANK VOLUME MUTE KEYSTONE MENU POSITION ENTER ESC (1) RESET (2) (4) (6) (3) (5) (7) (8) Thank you for purchasing this projector.
Content Content About this manual . . . . . . . . . . 1 Content . . . . . . . . . . . . . . . . . . 2 Projector features . . . . . . . . . . 3 Preparations . . . . . . . . . . . . . . 3 Contents of package . . . . . . . . . . . . .3 Fastening the lens cover . . . . . . . . . .3 Part names . . . . . . . . . . . . . . . 4 Projector . . . . . . . . . . . . . . . . . . . . . .4 Control panel . . . . . . . . . . . . . . . . . . .5 Rear panel . . . . . . . . . . . . . . . . . . . . .5 Remote control . . . . . .
Projector features / Preparations Projector features This projector has a capability to project various picture signals onto a screen. This projector requires only a minimal amount of space for installation and can produce a large projected image from even a short distance. This projector boasts a variety of I/O port and low noise. These features provide you with the broad use of this projector.
Part names Part names HOT! (1) Projector (1) Lamp cover ( 51) The lamp unit is inside. (2) Focus ring ( 18) (3) Zoom ring ( 18) (4) Control panel ( 5) (5) Elevator buttons (x 2) ( 18) (6) Elevator feet (x 2) ( 18) (7) Remote sensor ( 13) (8) Lens ( 18, 54) (9) Lens cover ( 3) (10) Intake vents (11) Filter cover ( 53) The air filter and intake vent are inside.
Part names Control panel (6) (5) (4) (1) STANDBY/ON button ( 15) (2) INPUT button ( 16, 22) (3) MENU button ( 22) It consists of four cursor buttons.
Part names Remote control (2) (1) (5) (10) (8) (9) (11) (16) (17) (20) (22) 17) (1) VIDEO button ( 16) (2) COMPUTER button ( 17) (3) SEARCH button ( 15) (4) STANDBY/ON button ( 17) (5) ASPECT button ( 19) (6) AUTO button ( 21) (7) BLANK button ( 20) (8) MAGNIFY - ON button ( VIDEO COMPUTER SEARCH MAGNIFY ON OFF FREEZE 14, 20) (11) END button ( 14) 2 MUTE KEYSTONE MENU ENTER RESET 16) 14, 16) (15) MUTE button ( 21) (16) FREEZE button ( (17) MY BUTTON - 1 button ( 42) (18)
Setting up Setting up Install the projector according to the environment and manner the projector will be used in. Arrangement Refer to the illustrations and tables below to determine screen size and projection distance. The values shown in the table are calculated for a full size screen: 1024×768.
Setting up Arrangement (continued) The values shown in the table are calculated for a full size screen: 1024×768. (a) Screen size (diagonal) (b) Projection distance (±10%) (c1), (c2) Screen height (±10%) On a horizontal surface Suspended from the ceiling • Keep a space of 30 cm or more between the sides of the projector and other objects such as walls. • Consult with your dealer before a special installation such as suspending from a ceiling.
Setting up WARNING ►Place the projector in a stable horizontal position. If the projector falls or is knocked over it could cause injury and/or damage to the projector. Using a damaged projector could then result in fire and/or electric shock. • Do not place the projector on an unstable, slanted or vibrational surface such as a wobbly or inclined stand. • Do not place the projector on its side, front or rear position.
Setting up Connecting your devices Be sure to read the manuals for devices before connecting them to the projector. Make sure that all the devices are suitable to be connected with this product, and prepare the cables required to connect. Please refer to the following illustrations to connect them.
Setting up Connecting your devices (continued) NOTE • Be sure to read the manuals for devices before connecting them to the projector, and make sure that all the devices are suitable to be connected with this product. Before connecting to a PC, check the signal level, the signal timing, and the resolution. - Some signal may need an adapter to input this projector. - Some PCs have multiple screen display modes that may include some signals which are not supported by this projector.
Setting up Connecting power supply At first, make sure that the power switch of the projector is set to OFF position (marked "O"). the connector of the power cord into 1. Put the AC inlet of the projector. plug the power cord’s plug into the 2. Firmly outlet. AC inlet Power cord WARNING ►Please use extra caution when connecting the power cord, as incorrect or faulty connections may result in fire and/or electrical shock. • Only use the power cord that came with the projector.
Remote control Remote control Putting batteries Please set the batteries to the remote control before using it. If the remote control starts to malfunction, try to replace the batteries. If you will not use the remote control for long period, remove the batteries from the remote control and store them in a safe place. the hook part of the battery 1. Holding cover, remove it. and insert the two AA batteries 2. Align according to their plus and minus terminals as indicated in the remote control.
Remote control Changing the frequency of remote control signal The accessory remote control has the two choices on signal frequency Mode 1:NORMAL and Mode 2:HIGH. If the remote control does not function properly, attempt to change the signal frequency. In order to set the Mode, please keep pressing the combination of two buttons listed below simultaneously for about 3 seconds. (1) Set to Mode 1:NORMAL... MUTE and RESET buttons (2) Set to Mode 2:HIGH...
Power on/off Power on/off Turning on the power sure that the power cord is firmly and correctly 1. Make connected to the projector and the outlet. the lens cover, and set the power switch to 2. Remove ON position (marked “ I “). The POWER indicator will light up in steady orange ( 56). Then wait several seconds because the buttons may not function for these several seconds. Press STANDBY/ON button on the projector or the remote control.
Operating Operating VOLUME Adjusting the volume VIDEO COMPUTER SEARCH 1. Press VOLUME button on the remote control. A dialog will appear on the screen to aid you in adjusting the volume. Use the ▲/▼ cursor buttons to adjust the volume. To close the dialog and complete the operation, press the VOLUME button again. Even if you do not do anything, the dialog will automatically disappear after a few seconds. ● When is selected for current picture input port, the volume adjustment is disable.
Operating Selecting an input signal (continued) VIDEO VIDEO button on the remote control. 1. Press Each time you press the button, the projector switches its input port as below.
Operating Adjusting the projector's elevator When the place to put the projector is slightly uneven to the left or right, use the elevator feet to place the projector horizontally. Using the feet can also tilt the projector in order to project at a suitable angle to the screen, elevating the front side of the projector within 10 degrees. This projector has 2 elevator feet and 2 elevator buttons. An elevator foot is adjustable while pushing the elevator button on the same side as it. 1.
Operating Using the automatic adjustment feature AUTO button on the remote control. 1. Press Pressing this button performs the following. AUTO For a computer signal The vertical position, the horizontal position and the horizontal phase will be automatically adjusted. And the horizontal size will be automatically set to the default. Make sure that the application window is set to its maximum size prior to attempting to use this feature. A dark picture may still be incorrectly adjusted.
Operating Correcting the keystone distortions KEYSTONE button on the remote control. A dialog will 1. Press appear on the screen to aid you in correcting the distortion. Use the ▲/▼ cursor buttons to select AUTO or MANUAL 2. operation, and press the ► button to perform the following. KEYSTONE VIDEO COMPUTER SEARCH ASPECT BLANK AUTO MAGNIFY (1) AUTO executes automatic vertical keystone correction. (2) MANUAL displays a dialog for keystone correction. Use the ▲/▼ buttons for adjustment.
Operating Freezing the screen FREEZE FREEZE button on the remote control. 1. Press The “FREEZE” indication will appear on the screen (however, the indication will not appear when TURN OFF is selected for MESSAGE item in SCREEN menu ( 39)), and the projector will go into the FREEZE mode. To exit the FREEZE mode and restore the screen to normal, press FREEZE button again.
Operating Using the menu function This projector has the following menus: PICTURE, IMAGE, INPUT, SETUP, SCREEN, OPTION and EASY MENU. EASY MENU consists of functions often used, and the other menus are classified into each purpose and brought together as Advanced Menu. Each of these menus is operated using the same methods. The basic operations of these menus are as follows.
Operating Using the menu function (continued) In the Advanced Menu Use the ▲/▼ cursor buttons to select a menu. If you want to change it to the EASY MENU, select EASY MENU. Then press the ► cursor button, or ENTER button to select an item. The lower layer menu of the selected item will appear. Advanced Menu Use the ▲/▼ cursor buttons to select an item to operate. Then press the ► cursor button, or ENTER button to progress. The operation menu of the selected item will appear.
EASY MENU EASY MENU From the EASY MENU, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons. Then perform it according to the following table. Item ASPECT Description Using the ◄/► buttons switches the mode for aspect ratio. See the ASPECT item in IMAGE menu ( 29). AUTO KEYSTONE EXECUTE Using the ► button executes the auto keystone function. See AUTO KEYSTONE EXECUTE item in SETUP menu ( KEYSTONE Using the ◄/► buttons corrects the vertical keystone distortion.
EASY MENU EASY MENU (continued) Item BRIGHTNESS CONTRAST COLOR TINT SHARPNESS WHISPER MIRROR RESET Description Using the ◄/► buttons adjusts the brightness. See BRIGHTNESS item in PICTURE menu ( 26). Using the ◄/► buttons adjusts the contrast. See CONTRAST item in PICTURE menu ( 26). Using the ◄/► buttons adjusts the strength of whole color. See COLOR item in PICTURE menu ( 26). Using the ◄/► buttons adjusts the tint. See TINT item in PICTURE menu ( 26). Using the ◄/► buttons adjusts the sharpness.
PICTURE Menu PICTURE Menu From the PICTURE menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table. Item BRIGHTNESS CONTRAST Description Using the ▲/▼ buttons adjusts the brightness. Light Ù Dark Using the ▲/▼ buttons adjusts the contrast. Strong Ù Weak Using the ▲/▼ buttons switches the gamma mode.
PICTURE Menu PICTURE Menu (continued) Item SHARPNESS Description Using the ▲/▼ buttons adjusts the sharpness. Strong Ù Weak • There may be some noise and/or the screen may flicker for a moment when an adjustment is made. This is not a malfunction. This projector has 4 memories for adjustment data (for all the items of PICTURE menu). Selecting a function using the ▲/▼ buttons and pressing the ► or ENTER button performs each function.
PICTURE Menu PICTURE Menu (continued) To adjust CUSTOM function in GAMMA and COLOR TEMP Selecting a mode whose name includes CUSTOM in GAMMA or COLOR TEMP item and then pressing the ► button or ENTER button displays a dialog to aid you in adjusting the mode. Choose an item using the ◄/► buttons, and adjust the level using the ▲/▼ buttons. • When this function is performed, lines or other distortion may appear.
IMAGE Menu IMAGE Menu From the IMAGE menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table. Item Description Using the ▲/▼ buttons switches the mode for aspect ratio.
IMAGE Menu IMAGE Menu (continued) Item Description H PHASE Using the ▲/▼ buttons adjusts the horizontal phase to eliminate flicker. Right Ù Left • This item can be selected only for a computer signal or component video signal. H SIZE Using the ▲/▼ buttons adjusts the horizontal size. Large Ù Small • This item can be selected only for a computer signal. • When this adjustment is excessive, the picture may not be displayed correctly.
INPUT Menu INPUT Menu From the INPUT menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table. Item Description PROGRESSIVE Using the ▲/▼ buttons switches the progress mode. TV Ù FILM Ù TURN OFF • This function is performed only for an interlaced signal of a video, s-video or component video of 525i (480i) or 625i (576i) signal.
INPUT Menu INPUT Menu (continued) Item Description VIDEO FORMAT The video format for S-VIDEO port and VIDEO port can be set. (1) Use the ◄/► buttons to select the input port. (2) Using the ▲/▼ buttons switches the mode for video format. AUTO Ù NTSC Ù PAL Ù SECAM N-PAL Ù M-PAL Ù NTSC4.43 • This item is performed only for a video signal from VIDEO port or S-VIDEO port. • The AUTO mode automatically selects the optimum mode. • The AUTO operation may not work well for some signals.
INPUT Menu INPUT Menu (continued) Item Description The resolution for the COMPUTER IN1 and IN2 input signals can be set on this projector. (1) In INPUT menu select RESOLUTION using the ▲/▼ buttons and press the ► button. The RESOLUTION menu will be displayed. (2) In the RESOLUTION menu, select the resolution you wish to display using the ▲/▼ buttons. Selecting AUTO will set a resolution appropriate to the input signal.
SETUP Menu SETUP Menu From the SETUP menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or the ENTER button to execute the item. Then perform it according to the following table. Item Description AUTO KEYSTONE EXECUTE Selecting this item performs the automatic keystone distortion correction. Projector automatically corrects vertical keystone distortion due to the (forward/backward) setup angle by itself.
SETUP Menu SETUP Menu (continued) Item Description WHISPER Using the ▲/▼ buttons turns off/on the whisper mode. NORMAL Ù WHISPER • When WHISPER is selected, acoustic noise and screen brightness are reduced. Using the ▲/▼ buttons switches the mode for mirror status. MIRROR NORMAL Ù H:INVERT Ù V:INVERT Ù H&V:INVERT If the Transition Detector is TURN ON and MIRROR status is changed, Transition Detector Alarm ( 49) will be displayed when projector is restarted after the power switch is turned off.
SCREEN Menu SCREEN Menu From the SCREEN menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table. Item Description Using the ▲/▼ buttons switches the OSD (On Screen Display) language.
SCREEN Menu SCREEN Menu (continued) Item Description Using the ▲/▼ buttons switches the mode for the start-up screen. The start-up screen is a screen displayed when no signal or an unsuitable signal is detected. MyScreen Ù ORIGINAL Ù TURN OFF MyScreen START UP ORIGINAL TURN OFF Feature Screen can be registered by the MyScreen item ( 38). Screen preset as the standard screen. Plain black screen.
SCREEN Menu SCREEN Menu (continued) Item Description MyScreen This item allows you to capture an image for use as a MyScreen image which can be used as the BLANK screen and START UP screen. Display the image you want to capture before executing the following procedure. 1. Selecting this item displays a dialog titled “MyScreen”. It will ask you if you start capturing an image from the current screen. Please wait for the target image to be displayed, and press the ENTER button when the image is displayed.
SCREEN Menu SCREEN Menu (continued) Item Description MESSAGE Using the ▲/▼ buttons turns on/off the message function. TURN ON Ù TURN OFF When the TURN ON is selected, the following message function works.
OPTION Menu OPTION Menu From the OPTION menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item, except for the items LAMP TIME and FILTER TIME. Then perform it according to the following table. Item AUTO SEARCH Description Using the ▲/▼ buttons turns on/off the automatic signal search function.
OPTION Menu OPTION Menu (continued) Item Description Using the ▲/▼ buttons adjusts the time to count down to automatically turn the projector off. Long (max. 99 minutes) Ù Short (min. 0 minute = DISABLE) AUTO OFF When the time is set to 0, the projector is not turned off automatically. When the time is set to 1 to 99, and when the passed time with nosignal or an unsuitable signal reaches at the set time, the projector lamp will be turned off.
OPTION Menu OPTION Menu (continued) Item MY BUTTON Description This item is to assign one of the following functions to MY BUTTON 1 and 2 on the remote control ( 6). Choose 1 or 2 on the MY BUTTON menu using the ◄/► button first. Then using the ▲/▼ buttons sets one of the following functions to the chosen button. • COMPUTER1: Sets port to COMPUTER IN1. • COMPUTER2: Sets port to COMPUTER IN2. • COMPONENT: Sets port to COMPONENT(Y, Cb/Pb, Cr/Pr) • S-VIDEO: Sets port to S-VIDEO. • VIDEO: Sets port to VIDEO.
OPTION Menu OPTION Menu (continued) Item Description AUTO ADJUST Using the ▲/▼ buttons enables/disables the automatic adjustment. When DISABLE is selected, the automatic adjustment feature is disabled, although rough adjustment is automatically performed depending on the basic setting. FINE Ù FAST Ù DISABLE FINE: Finer tuning including H.SIZE adjustment. FAST: Faster tuning, setting H.SIZE to prearranged data for the input signal.
OPTION Menu OPTION Menu (continued) Item Description KEY LOCK Using the ▲/▼ buttons turns on/off the key lock feature. When TURN ON is selected, the buttons on the projector except the STANDBY/ON button are locked. TURN ON Ù TURN OFF • Please use to avoid a mischief and touching accidentally. This function does not have any effect on the remote control. SERVICE (continued) REMOTE FREQ. Use the ▲/▼ button to change the projector's remote sensor setting. 1:NORMAL Ù 2:HIGH Items with a checkmark are on.
OPTION Menu OPTION Menu (continued) Item Description This projector is equipped with security functions. User registration is required before using the security functions. Please contact your local dealer. 1. Using Security Features 1.1 Inputting the PASSWORD 1.1-1 Use the ▲/▼ buttons on the OPTION menu to select SECURITY and press the ► button. The ENTER PASSWORD box will be displayed. The factory default PASSWORD is 1273. This PASSWORD can be changed (1.2 Changing the PASSWORD).
OPTION Menu OPTION Menu (continued) Item Description 1.3 If you have forgotten your PASSWORD 1.3-1 Follow the procedure in 1.1-1 to display the ENTER PASSWORD box. 1.3-2 While the ENTER PASSWORD box is displayed, press and hold the RESET button for about 3 seconds or press and hold the INPUT and ► buttons on the projector for about 3 seconds. The 10-digit Inquiring Code will be displayed. • If there is no key input for about 55 seconds while the Inquiring Code is displayed the menu will close.
OPTION Menu OPTION Menu (continued) Item Description 2.2-4 Move the cursor to the right side of the PASSWORD AGAIN box and press the ► button to display the PASSWORD for about 20 seconds, please make note of the PASSWORD during this time. Pressing the ENTER button will return to MyScreen PASS WORD on/off menu. When a PASSWORD is set for MyScreen: • The MyScreen registration function (and menu) will be unavailable. • The MyScreen Lock function (and menu) will be unavailable.
OPTION Menu OPTION Menu (continued) Item Description 3.1-2 Use the ▲/▼ buttons on the PIN LOCK on/off menu to select TURN ON and the PIN BOX will be displayed. SECURITY (continued) 3.1-3 Input a 4 part PIN Code using the ▲, ▼, ◄, ►, COMPUTER and INPUT buttons. A PIN Code again box will appear. Reenter the same PIN Code. This will complete the PIN Code registration. • If there is no key input for about 55 seconds while the PIN BOX or the PIN Code again box are displayed the menu will close.
OPTION Menu OPTION Menu (continued) Item Description 4. Using the Transition Detector Function While the Transition Detector function is ON, when power switch is started to supply to the projector, it might react as below. • Transition Detector alarm shown below might appear on screen, if the projector has been moved or re-installed. • Transition Detector alarm might appear on screen, if the MIRROR setting has been changed.
OPTION Menu OPTION Menu (continued) Item Description 4.2-4 Move the cursor to the right side of the PASSWORD AGAIN box and press the ► button to display the PASSWORD for about 20 seconds, please make note of the PASSWORD during this time. Pressing the ENTER button will return to the TRANSITION DETECTOR on/off menu. • Please do not forget your Transition Detector PASSWORD. 4.3 Setting the Transition Detector off 4.3-1 Follow the procedure in 4.1-1 to display the TRANSITION DETECTOR on/off menu.
Maintenance Maintenance Lamp A lamp has finite product life. Using the lamp for long periods of time could cause the pictures darker or the color tone poor. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. Preparation of a new lamp and early replacement are recommended. To prepare a new lamp, contact your dealer and tell the lamp type number. Type number : RLC-031 Replacing the lamp the projector off, and unplug the power cord. 1.
Maintenance Lamp (continued) Lamp warning HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE WARNING ►The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them.
Maintenance Air filter Please check and clean the air filter periodically. When the indicators or a message prompts you to clean the air filter, comply with it as soon as possible. Replace the air filter when it is damaged or too soiled. To prepare a new air filter, contact your dealer and tell the air filter type number. When you replace the lamp, please replace the air filter. An air filter of specified type will come together with a replacement lamp for this projector.
Maintenance Other care Inside of the projector In order to ensure the safe use of your projector, please have it cleaned and inspected by your dealer about once every year. Caring for the lens If the lens is flawed, soiled or fogged, it could cause deterioration of display quality. Please take care of the lens, being cautious of handling. Turn the projector off, and unplug the power cord. Allow the projector to cool sufficiently.
Troubleshooting Troubleshooting If an abnormal operation should occur, stop using the projector immediately. WARNING ►Never use the projector if abnormal operations such as smoke, strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. should occur. In such cases, immediately disconnect the power plug from the power outlet. After making sure that the smoke or odor has stopped, contact your dealer or service company.
Troubleshooting Regarding the indicator lamps When operation of the LAMP, TEMP and POWER indicators differs from usual, check and cope with it according to the following table. POWER LAMP TEMP Description indicator indicator indicator Lighting Turned Turned The projector is in a standby state. In Orange off off Please refer to the section “Power on/off”. Blinking In Green Turned off Turned off The projector is warming up. Lighting In Green Turned off Turned off The projector is in an on state.
Troubleshooting Regarding the indicator lamps (continued) POWER LAMP TEMP indicator indicator indicator Description There is a possibility that the interior portion has become heated. Blinking In Red or Lighting In Red Turned off Lighting In Red Please turn the power off, and allow the projector to cool down at least 20 minutes. After the projector has sufficiently cooled down, please make confirmation of the following items, and then turn the power on again.
Troubleshooting Phenomena that may be easy to be mistaken for machine defects About the phenomenon confused with a machine defect, check and cope with it according to the following table. Phenomenon Reference page Cases not involving a machine defect The electrical power cord is not plugged in. 12 Correctly connect the power cord. The main power source has been interrupted during operation such as by a power outage (blackout), etc. Power does not come on.
Troubleshooting Phenomena that may be easy to be mistaken for machine defects (continued) Phenomenon Reference page Cases not involving a machine defect The brightness is adjusted to an extremely low level. Adjust BRIGHTNESS to a higher level using the menu function. No pictures are displayed. (continued) The computer cannot detect the projector as a plug and play monitor. Make sure that the computer can detect a plug and play monitor using another plug and play monitor. The BLANK screen is displayed.
Specifications Specifications Specification Item Specification Product name Panel size Liquid Crystal Drive system Panel Pixels Liquid crystal projector 1.6 cm (0.63 type) TFT active matrix 786,432 pixels (1024 horizontal x 768 vertical) Zoom lens, F=1.7 ~ 1.9 F=1.7 ~ 1.9 F=1.6 ~ 1.8 f = 18.9~ 22.6 mm f = 19.5~ 23.4 mm f = 18.9~ 22.6 mm Lens (approximately) Lamp 220W UHB Audio output 7W Power supply Power consumption Temperature range AC 100-120V/3.5A, AC220-240V/1.
Specifications Specifications (continued) [unit: mm] ViewSonic 61 Downloaded From projector-manual.
Customer Support For technical support or product service, see the table below or contact your reseller. Note : You will need the product serial number. Country/Region Web Site United States www.viewsonic.com T=Telephone F=Fax E-mail T= 800 688 6688 service.us@viewsonic.com F= 909 468 1202 T= 1-800-688-6688 (English) service.us@viewsonic.com Puerto Rico & Virgin Islands www.viewsonic.com T= 1-866-379-1304 (Spanish) soporte@viewsonic.com F= 1-909-468-1202 T= 1-866-463-4775 Canada www.viewsonic.
Limited Warranty VIEWSONIC® PROJECTOR What the warranty covers: ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components.
Limitation of implied warranties: There are no warranties, express or implied, which extend beyond the description contained herein including the implied warranty of merchantability and fitness for a particular purpose. Exclusion of damages: ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for: 1.
Downloaded From projector-manual.
