Service Manual ViewSonic VX2433wm-1 VX2433wm-CN Model No. VS12324 23.6” Wide Color TFT LCD Display (VX2433wm-1_VX2433wm-CN _SM Rev. 1b Feb.
Copyright Copyright © 2009 by ViewSonic Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of ViewSonic Corporation.
TABLE OF CONTENTS 1. Precautions and Safety Notices ......................................................................................... 1 2. Specification ....................................................................................................................... 4 3. Front Panel Function Control Description ..................................................................... 13 4. Circuit Description ........................................................................................
1. Precautions and Safety Notices 1. SAFETY PRECAUTIONS This monitor is manufactured and tested on a ground principle that a user’s safety comes first. However, improper used or installation may cause damage to the monitor as well as to the user. WARNINGS: z This monitor should be operated only at the correct power sources indicated on the label on the rear of the monitor. If you’re unsure of the power supply in you residence, consult your local dealer or Power Company.
Handling and Placing Methods ViewSonic Corporation 2 VX2433wm-1 CONFIDENTIAL – DO NOT COPY VX2433wm-CN
ViewSonic Corporation 3 VX2433wm-1 CONFIDENTIAL – DO NOT COPY VX2433wm-CN
2. Specification 2.1 INTRODUCTION 1 LCD PANEL Panel: ʳ CMO (M236H1-L01 ver0.0) Size ʳ 23.6” Wide Color a-Si TFT Active Matrix LCD Display area ʳ ʳ 525.22(W) x 297.22(H) mm Optimum Resolution ʳ 1920x1080(WUXGA) Pixel Pitch Glass Treatment ʳ Anti-Glare, Hard coating (3H),Haze25 Contrast Ratio CR >= 10 1000 :1 Dynamic Contrast ʳ 20000:1 (typ.) Viewing Angle 170/160 (degrees; typ) Colors 16.7Mcolors (6 bit +Hi FRC panel) Luminance 300 cd/m2 @8.0mA(typ.
ERGONOMICS 9 CONTROLS Tilt Range ʳ 20 ~ -5 degrees Swivel N/A Rotation N/A Height Adjust N/A Physical Key buttons ʳ ] [ [ 1 ] [ 2 ] [ź] [Ÿ] OSD Function Main Menu ʳ Auto Image Adjust ʳ Contrast/Brightness Input Select D-SUB, DVI,HDMI PC,HDMI AV Audio Adjust Volume, Mute Color Adjust sRGB, 9300K, 7500K, 6500K, 5000K, User Color [R, G, B] Information Manual Image Adjust H/V Position, Horizontal Size, Fine Tune, Sharpness, Dynamic Contrast, Response Time, Aspect ratio, Display Mode, Eco
without OSD message.
UPC Code 20' 76690732861 5 40' Serial Format 19 Wall Mount VX2433wm-1 R4F VX2433wm-CN R8W EDID Code 2238 Country of origin China VESA 100mm x 100mm 20 OTHERS DDC/2B, DDC/CI, HDCP, Detachable Base, KENSINGTON MicroSaver Security Compatible, WorldWide Model, Vista Premium, SRS WOW HD,HDMI 21 Package LCD Display Contents Power Cable Audio Cable VGA Cable DVI Cable Quick Start Guide ( One page) ViewSonic Wizard CD-ROM 22 EU Packaging Information Carton -- One piece construction with double
2.2 PRODUCT DEFINITION AND SPECIFICATION Product Name ViewSonic VX2433wm Oracle P/N VX2433WM/VX2433WM-CN Model Number OSD Languages: 11 VS12324 English, French, German,Italian, Spanish, Finnish, Russian Japanese, Korean, S. Chinese, T. Chinese 1st panel: CMO M236H1-L01 TFT LCD Panel and Model # Scalar Novatek NT68672 Input Signal D-Sub / DVI-D/HDMI Sync Compatibility Separate Sync/ Composite Sync / SOG Adapter Internal Power Board Yes Power Cable Analog Cable (1.
2.3 GENERAL SPECIFICATION Test Resolution & Frequency 1920x1080 @ 60Hz Test Image Size Full Size Contrast and Brightness Controls Factory Default: Contrast = 70%, Brightness = 100% 2.
2.5 POWER SUPPLY Internal Power Supply ILPI-107 Input Voltage Range 90 to 264 VAC Input Frequency Range 47 to 63 Hertz Short Circuit Protection Output can be shorted without safety issue Over Current Protection 5.0A typical at 24VDC ( Protect when short circuit) Leakage Current 3.
2.6 ELECTRICAL REQUIREMENT Horizontal / Vertical Frequency Horizontal Frequency 24 – 83 kHz Vertical Refresh Rate 50 –76* Hz Maximum Pixel Clock Analog : 205 MHz Digital : 175 MHz Sync Polarity Independent of sync polarity Timing Table SOG Timing Composite Separated Item Digital - TMDS Analog Remark 1 640 x 350 @ 70 Hz, 31.5 KHz v v v v DMT 2 640 x 400 @ 60 Hz, 31.5 KHz v v v v DMT 3 640 x 400 @ 70 Hz, 31.5 KHz v v v v DMT 4 640 x 480 @ 50 Hz, 24.
24 1152 x 870 @ 75 Hz, 68.7 KHz v v v v For MAC 25 1152 x 900 @ 67 Hz, 62.5 KHz v v v v For SUN 26 1280 x 720 @ 50 Hz, 37.5 KHz v v v v DTV 27 1280 x 720 @ 60 Hz, KHz v v v v DTV 28 1280 x 768 @ 50 Hz, 39.6 KHz v v v v DMT; 29 1280 x 768 @ 60 Hz, 47.8 KHz v v v v DMT; 30 1280 x 768 @ 75 Hz, 60.3 KHz v v v v DMT; 31 1280 x 960 @ 50 Hz, 49.4 KHz v v v v DMT 32 1280 x 960 @ 60 Hz, 60.0 KHz v v v v DMT 33 1280 x 960 @ 75 Hz, 75.
Primary Presets 1920x1080 @ 60Hz User Presets Number of User Presets (recognized timings) Available: 10 presets total in FIFO configuration Changing Modes ϥʳ Maximum Mode Change Blank Time for image stability : 3 seconds (Max), excluding “Auto Adjust” time ϥʳ It should recall factory setting when execute Auto Image Adjust function by following conditions, 1. Memory recall under DOS mode (640 x 350, 720 x 400 & 640 x 400). 2. New timing mode detected under DOS mode (640 x 350, 720 x 400 & 640 x 400).
3. Front Panel Function Control Description 3.1 FRONT PANEL HARDWARE CONTROLS Power Switch (Front Head) AC Power Switch on the back cover Soft Power Switch on the front bezel Power LED (Front Head) Blue – ON Amber – Active Off Dark = Soft Power Switch OFF Front Panel Controls (Head) [ 1 ] [ 2 ] [ ] [ź] [Ÿ] [ ] Power [ 1 ] BUTTON 1 [ 2 ] Button 2 [Ÿ] UP ARROW BUTTON [ź] DOWN ARROW BUTTON Note: Power Button, Button 1 and Button 2 must be one-shot logic operation. (i.e.
When switch to AUDIO IN (earphone jack) [ź]+ [Ÿ] 1. In the CR/ BT menu, Recall Contrast or Brightness to default in its menu without OSD message. 2. In the Audio menu, Recall both of audio volume and mute to default without OSD message. * While OSD menu off, recall CR/ BT/ Audio volume and mute to default without OSD message [1] + [2] Toggle 720x400 and 640x400 mode when input 720x400 or 640x400 mode * Default = 720 x 400 [1] + [ź] + [Ÿ] (Keep pushing 5 sec) White Balance 1.
When switch to DDC/CI When switch to DDC/2B Default = DDC/CI Signal + [2] + [ ] Factory Mode Remark : All the short cuts function are only available while OSD off 3.3 MAIN MENU OSD TABLE Main Menu 1.
Jump to Contrast OSD directly Contrast 1. Adjust range = 0 to 100 2. Default = 70 3. Key button definition: [1] = Back to Main Menu or OSD off (depend on previous status) [2] = Change to Brightness OSD [Up] = Increase the OSD value setting [Dn] = Decrease the OSD value [Up]+[Dn]: Recall to default ʳ Brightness 1. Adjust range = 0 to 100 2. Default = 100 3.
2. Key button definition: Step 3: Show on Input Message [1]: Back to previous OSD status OSD at the right-top corner of [2]: Change to the selected input screen for 1 second. port [Up]: Move up the slider [Dn]: Move down the slider DVI Step 1: Turn off OSD. Step 2: 1. Target video input port = Digital 2. If signal detected from target port, change to target port. 3. If no signal detected from target port, keep existing input port.
1. Target video input port = HDMI AV 2. If signal detected from target port, change to target port. 3. If no signal detected from target port, keep existing input port. Step 3: Show on Input Message OSD at the right-top corner of screen for 1 second. HDMI Audio Adjust AV ʳ Volume 1. Adjust range = 0 to 100 2. Default = 50 3. Key button definition: [1]: Back to Audio Adjust OSD 1. The selected icon in Mute will be highlighted [Up]: Increase the volume setting [Dn]: Decrease the volume setting 2.
1. Show on existing input port by red color Change Color setting to 6500K ʳ 5000K Change Color setting to 5000K 2. Default = 6500K User Color 3. Key button definition: Jump to Red OSD directly Red [1]: Back to previous OSD status [2]: Change to the selected color setting 1. Adjust range = 0 to 100 [Up]: Move up the slider 2. Default = 100 [Dn]: Move down the slider 3. Key button definition: [1]: Back to Color Adjust OSD 4.
[Up]: Increase the OSD value setting [Dn]: decrease the OSD value setting Information ʳ ʳ H/V Position Horizontal Position PC timing – Display Resolution Video timing – Display Video Format Key button definition: [1]: Back to Main Menu OSD Manual Image Adjust Jump to Horizontal Position OSD directly 1. Adjust range = 0 to 100 2. Key button definition: [1]: Back to Manual Image Adjust OSD [2]: Change to Vertical Position OSD 1.
(When push the button on the 2. Key button definition: bottom position, the slider shall go [1]: Back to Manual Image Adjust OSD down to the top item [2]: Change to Horizontal Position OSD 2. Under Digital mode, all the H./V. [Up]: Increase the OSD value setting Position, Horizontal Size and Fine Tune shall be disabled with gray [Dn]: Decrease the OSD value ʳ Horizontal Size color. And it should not be selected. 3. Under native mode, Sharpness shall be disabled with gray color.
[Dn]: Decrease the OSD value ʳ Dynamic Contrast Swap on and off the Dynamic Contrast function Default = Off When Dynamic Contrast is on, below functions will be disabled: 1. Brightness/Contrast menu 2. SRGB selection in Color Adjust 3. White balance hot key 4. DDC/CI BR/CT adjustment Response Time Standard Over Drive = off 1. Show on existing Response Time setting by red color 2. Key button definition: [1]: Back to previous OSD status [2]: Change to the selected Response Time setting.
( faster than level 1) Aspect Ratio 4:3 Change aspect ratio to 4:3 Full Screen Fill screen with panel native aspect ratio. 1. Show on existing Aspect Ratio setting by red color 2. Key button definition: [1]: Back to previous OSD status [2]: Change to the selected Display Mode setting.
setting by red color 3. Key button definition: [1]: Back to previous OSD status [2]: Change to the selected Display Mode setting. [Up]: Scroll up the slider (When push the button on the top position, the slider shall go down to the bottom item) [Dn]: Scroll down the slider (When push the button on the bottom position, the slider shall go up to the top item) 4. Save PC timing and DTV timing setting separately. 5. Default = RGB Mode ( DVI &VGA) , 6.
Mode setting. [Up]: Scroll up the slider (When push the button on the top position, the slider shall go down to the bottom item) [Dn]: Scroll down the slider (When push the button on the bottom position, the slider shall go up to the top item) 4. Default = Standard 5. Under sRGB mode, ECO Mode shall be disabled with gray color. And it should not be selected. 6. No matter DCR on or off, lamp current will be changed by ECO mode change. 7.
Setup Menu Language Select English Set OSD language to English and keep in Language Select OSD French Set OSD language to French and keep in Language Select OSD German 1. Key button definition: [1]: Back to Main Menu OSD [2]: Execute the selected function [Up]: Rolling up the slider Set OSD language to German and 1. Show on existing input port by red color keep in Language Select OSD Spanish 2.
ʳ Resolution Notice Swap on and off the Resolution Notice function OSD Position OSD H. Position Jump to OSD H. Position OSD directly 1. Adjust range = 0 to 100 2. Default = 50 3. Key button definition: [1]: Back to Setup Menu OSD [2]: Change to OSD V. Position OSD [Up]: Increase the OSD value setting (move OSD right) [Dn]: Decrease the OSD value setting (move OSD left) [Up]+[Dn]: Recall to default value OSD V. Position 1. Adjust range = 0 to 100 2. Default = 50 3.
OSD Time Out 5 Set OSD Time Out to 5 Seconds 15 Set OSD Time Out to 15 Seconds 1. Adjust range = 5, 15, 30, 60 30 2. Default = 15 Set OSD Time Out to 30 Seconds 3.
(When push the button on the top position, the slider shall go down to the bottom item [Dn]: Rolling down the slider (When push the button on the bottom position, the slider shall go down to the top item ʳ Memory Recall 1. Background = blanking 2. Recall white balance to factory setting 3. Recall all the OSD setting to the default. (include the R/G/B in User Color) 4. Show the message OSD position is at the center for 3 seconds. 5. Clean FIFO timing mode buffer 6.
3.4 OSD LOCK SHORT CUTS FUNCTION FOR THE BUTTONS The OSD lock will be activated by pressing the front panel control buttons [1] + [Ÿ] for 10 seconds *1. If the user then tries to access the OSD by pressing any of the buttons, a message will appear on the screen for 3 seconds showing "OSD Locked" *2. The OSD lock will be deactivated by pressing the front panel control buttons [1] + [Ÿ] again for 10 seconds*3.
3.5 POWER LOCK SHORT CUTS FUNCTION FOR THE BUTTONS The Power lock will be activated by pressing the front panel control buttons [1] + [ź] for 10 seconds *1. Locking the power button means that the user won't be able to turn off the LCD while the power button is locked. If the user presses the power button while it is locked, a message will appear on the screen for 3 seconds showing "Power Button Locked" *2.
3.6 RESOLUTION NOTICE ACTIONS 1. Resolution Notice OSD should show on screen after changing to non-native mode for 30 sec 2. Key button definition: [1]: Turn off the OSD message. [2]: Turn off the OSD message and disable Resolution Notice function 3. The OSD should disappear after 10 sec or by pushing button [1] or [2] 4. After the OSD turns off, it will not show on again before next timing change, input change or power off. 5.
3.10 NO SIGNAL FOR D-SUB / DVI While no signal is detected for D-Sub and DVI, the following OSD message shall shows on 3 seconds then go in to power saving. OSD Background = Non-transparent Image = Blanking 3.11 ACTORY DEFAULTS Item Defaults Item Defaults Contrast 70% OSD Time Out 15 Sec Brightness 100% OSD Background On Color Temperature 6500K Volume 80% Sharpness 100% Treble N/A OSD H. Position 50% Bass N/A OSD V.
Packing For Shipping And Disassembly Procedure Packing For Shipping 1. Packing Procedure Paste protection film to protect the monitor. (Figure 1) Put the monitor in the PE bag and seal the bag with tape. (Figure 2) Figure 1 Figure 2 Put the cushions on the monitor. Place the monitor into the carton and then put all the accessories into the carton. At last, close the carton and seal it with tape.
Disassembly Procedure BASE STAND ViewSonic Corporation 36 VX2433wm-1 CONFIDENTIAL – DO NOT COPY VX2433wm-CN
BACKCOVER ViewSonic Corporation 37 VX2433wm-1 CONFIDENTIAL – DO NOT COPY VX2433wm-CN
PANEL BEZEL ViewSonic Corporation 38 VX2433wm-1 CONFIDENTIAL – DO NOT COPY VX2433wm-CN
KEYPAD CHASIS ViewSonic Corporation 39 VX2433wm-1 CONFIDENTIAL – DO NOT COPY VX2433wm-CN
POWER BOARD LVD CABLE SHORT KEYPAD-CABLE ViewSonic Corporation 40 VX2433wm-1 CONFIDENTIAL – DO NOT COPY VX2433wm-CN
IF BOARD ViewSonic Corporation 41 VX2433wm-1 CONFIDENTIAL – DO NOT COPY VX2433wm-CN
4. Circuit Description 4.1 Switching Mode Power Supply 4.3.1 AC Current Input Circuit P801 is a connector for connecting AC Power. F801 is a fuse to protect all the circuit. AC input voltage is from 90v to 264V. R801,R831 and R802 joined between two inputting main circuit to prevent man from shock. L801 is used to clear up low frequency wave. C801 and C802 are used to discharge the waves that L801 produced. High frequency waves are damped by C801 and C802.
4.2 Inverter Circuit 1. R503, ZD501, R502, Q501 components convert +14V voltage into +5.0V voltage, and the voltage supply to IC501. The extra PWM pulse signal (BRIGHTNESS signal) input to control IC through R512, R514, C510, The LCT pin is set to a DC voltage of 0.7V by using a resistor divider(R507, R516), change the duty of PWM pulse, will regulate the lamp current.
In addition, NT68673UMFG includes an integrated 8-Bit Microcontroller (MCU). It contains an 8-bit 8031 micro-controller, 5,120-bytes internal data memory, eight 7-bit resolution A/D Converter, 10- channel 8-bit resolution PWM DAC, two16-bit timer/counters, and a UART. Except those, it has two channel hardware DDC solution, and VESA 2Bi/2B+ master/slave I2C bus interface. It can support up to External 512 K Bytes SPI Flash memories for program memory. 2.
4.4 Power On/Off Sequence 4.4.1 Hardware Power ON When power cord is plugged into AC socket, SMPS starts work and provides U105 with VCC5V. When VCC5V inputs, U105 resets circuit active, sets U105 all registers to preset modes, and then monitor goes into stand-by mode. That means hardware power on has been completed. 4.4.2 Software Power ON/OFF When press power key, U105 # 74 recieves low pulse,and then U105 will do the power on/off.
4.5 4.5.1 4.5.2 4.5.3 Inner Connector Pin Assignment CN501, CN502, CN503, CN504 (Connect to Panel Backlight, SM02B-BHSS-1-TB or equivalent) Pin Symbol Description 1 H.V. High voltage for lamp 2 L.V. Low voltage for lamp CN101 (Power BD to Interface BD) Pin No.
4.5.5 25 RXO2+ Positive LVDS differential data input.Channel O2(odd) 24 GND Ground 23 RXOC- Negative LVDS differential clock input (odd) 22 RXOC+ Positive LVDS differential clock input (odd) 21 RXO3- Negative LVDS differential data input.Channel O3(odd) 20 RXO3+ Positive LVDS differential data input.Channel O3(odd) 19 RXE0- Negative LVDS differential data input.Channel E0(even) 18 RXE0+ Positive LVDS differential data input.
4.6 Key Parts Pin Assignment 4.6.1 IC802 (TOP245Y or TOP246Y, Power Control IC) Pin Symbol I/O 1 BO I Brown-out and external triggering 2 FB I Sets the peak current setpoint 3 CS I Current sense input and overpower compensation adjustment 4 GND 5 DRV O Output driver 6 VCC I IC supply 7 NC 8 HV I High-Voltage pin 4.6.2 Pin No. Description IC ground IC501 (OZ9938GN, CCFL inverter controller IC) Symbol I/O Description Open lamp voltage feedback input 2.
In single lamp application, connect this pin to LI2 pin. Lamp current feedback 2. The function of this pin is same as LI1. In 3 LI2 I single lamp application, connect this pin to LI1. In multi-lamp application, this pin is used for lamp current feedback which is out-of-phase of LI1. Feedback Compensation Node. Connect a compensation capacitor from this pin to GND. This pin is also used for IC enable control. A logic low 4 COMP I (below 0.5V) input turns off the IC.
5. Adjustment Procedure 5.1 Key Function Description Power Switch AC Power Switch on the back cover Soft Power Switch on the front bezel Power LED (Front Head) Blue – ON Amber – Active Off Dark = Soft Power Switch OFF Front Panel Controls (Head) [ 1 ] [ 2 ] [ ] [Ÿ] [ź] [ ] Power [ 1 ] Button 1 [ 2 ] Button 2 [Ÿ] Up arrow button [ź] Down arrow button Note: Power Button, Button 1 and Button 2 must be one-shot logic operation. (i.e.
When switch to HDMI When switch to AUDIO IN (earphone jack) [ź]+ [Ÿ] 1. In the CR/ BT menu, Recall Contrast or Brightness to default in its menu without OSD message. 2. In the Audio menu, Recall both of audio volume and mute to default without OSD message. * While OSD menu off, recall CR/ BT/ Audio volume and mute to default without OSD message. [1] + [2] Toggle 720x400 and 640x400 mode when input 720x400 or 640x400 mode * Default = 720 x 400 [1] + [ź] + [Ÿ] (Keep pushing 5 sec) White Balance 1.
[1] + [Ÿ] OSD Lock / Unlock (refer to segment 4-6-4) [1] + [ź] Power Lock / Unlock (refer to segment 4-6-5) [2] + [ź] Toggle DDC/CI and DDC/2B (DDC/CI enable/disable) and show following message for 3 seconds, When switch to DDC/CI When switch to DDC/2B Default = DDC/CI Signal + [2] + [ ] Factory Mode Remark : All the short cuts function are only available while OSD off 5.3 OSD Control 5.3.
*3 The OSD Unlock message as below, Range = 0 to 10 *4 When the OSD is locked will lock all functions, including “Volume”, “Mute” and others. *5 Status bar indicating OSD Lock or Unlock is in progress and when complete it will indicate “OSD Locked” or “OSD Unlocked” for 3 seconds as below, OSD Locked OSD Unlocked *6 When OSD appears on screen, the OSD Lock/Unlock short cut key will be disabled. 5.3.
*3 The Unlocking Power Button message as below, Range = 0 to 10 *5 Status bar indicating Power Button Lock or Unlock is in progress and when complete it will indicate “Power Button Locked” or “Button Unlocked” for 3 seconds as below, Power Button Locked Button Unlocked *6 When OSD appears on screen, the OSD Lock/Unlock short cut key will be disabled. 5.
5.5 Function description: ! Input Signal Notice Actions 1. The Input Signal Notice OSD appears 1 second when power turns on or change input signal. 2. The Input Signal Notice OSD position is on the right-top side of image. 3. The OSD message as below, Resolution Notice Actions 7. Resolution Notice OSD should show on screen after changing to non-native mode for 30 sec. 8. Key button definition: [1]: Turn off the OSD message. [2]: Turn off the OSD message and disable Resolution Notice function 9.
OSD Auto Save The OSD shall save new settings when it is turned off by the user or when it times out. There shall not be a separate save Out of range While non-defined timing is detected, following OSD message will keeps showing on, 1. If the timing is over spec (Fh, Fv or dot clock), the image shall be blanking, and OSD background shall be non-transparent. 2. If the timing is inspect but not defined, the image shall be non-blanking.
5.6 OSD Structure Main Menu 1.
3. Key button definition: [1] = Back to Main Menu or OSD off (depend on previous status) [2] = Change to Brightness OSD [Up] = Increase the OSD value setting [Dn] = Decrease the OSD value [Up]+[Dn]: Recall to default ʳ Brightness 1. Adjust range = 0 to 100 2. Default = 100 3.
[Up]: Move up the slider DVI [Dn]: Move down the slider Step 1: Turn off OSD. Step 2: 1. Target video input port = Digital 2. If signal detected from target port, change to target port. 3. If no signal detected from target port, keep existing input port. Step 3: Show on Input Message OSD at the right-top corner of screen for 1 second. HDMI PC Step 1: Turn off OSD. Step 2: 1. Target video input port = HDMI PC 2. If signal detected from target port, change to target port. 3.
right-top corner of screen for 1 second. HDMI Audio Adjust AV Volume 1. Adjust range = 0 to 100 2. Default =50 3. Key button definition: [1]: Back to Audio Adjust OSD 1. The selected icon in Mute will be highlighted [Up]: Increase the volume setting [Dn]: Decrease the volume setting 2. Key button definition: Mute [1]: Back to previous OSD status 1. Default = Off [2]: Change to Volume or Mute the 2.
[2]: Change to the selected color setting 1. Adjust range = 0 to 100 [Up]: Move up the slider 2. Default = 100 [Dn]: Move down the slider 3. Key button definition: [1]: Back to Color Adjust OSD 4. Under DCR mode (Dynamic [2]: Jump to Green OSD Contrast = On), SRGB shall be [Up]: Increase the OSD value setting disabled with gray color. And it [Dn]: decrease the OSD value should not be selected. setting Green 1. Adjust range = 0 to 100 2. Default = 100 3.
Information ʳ ʳ H/V Position Horizontal Position PC timing – Display Resolution Video timing – Display Video Format Key button definition: [1]: Back to Main Menu OSD Manual Image Adjust Jump to Horizontal Position OSD directly 1. Adjust range = 0 to 100 2. Key button definition: [1]: Back to Manual Image Adjust OSD 1.
[Dn]: Scroll down the slider Vertical Position (When push the button on the bottom position, the slider shall go down to the top item 2. Under Digital mode, all the H./V. Position, Horizontal Size and Fine 1. Adjust range = 0 to 100 Tune shall be disabled with gray 2. Key button definition: color. And it should not be [1]: Back to Manual Image Adjust selected. OSD 3. Under native mode, Sharpness [2]: Change to Horizontal Position shall be disabled with gray color.
1. Adjust range ={0,25,50,75,100} 2. Default = 50 3. Key button definition: [1]: Back to Manual Image Adjust OSD [Up]: Increase the OSD value setting [Dn]: Decrease the OSD value Dynamic Contrast Swap on and off the Dynamic Contrast function Default = Off When Dynamic Contrast is on, below functions will be disabled: 5. Brightness/Contrast menu 6. SRGB selection in Color Adjust 7. White balance hot key 8. DDC/CI BR/CT adjustment Response Time Standard Over Drive = off 1.
Aspect Ratio 4:3 Change aspect ratio to 4:3ʳ 3. Show on existing Aspect Ratio setting by red color 2. Key button definition: Full Screen [1]: Back to previous OSD status Fill screen with panel native aspect [2]: Change to the selected Display Mode ratio. ʳ setting. [Up]: Scroll up the slider (When push the button on the top position, the slider shall go down to the bottom item) [Dn]: Scroll down the slider (When push the button on the bottom position, the slider shall go up to the top item) 3.
display mode. YUV Mode 2. Show on existing Display Mode setting by red Set color space to YUV for HD timing color mode 3. Key button definition: [1]: Back to previous OSD status [2]: Change to the selected Display Mode setting. [Up]: Scroll up the slider (When push the button on the top position, the slider shall go down to the bottom item) [Dn]: Scroll down the slider (When push the button on the bottom position, the slider shall go up to the top item) 4.
ECO Mode Standard 1. This function toggles ECO mode. 2. Show on existing ECO Mode setting by red color 3. Key button definition: [1]: Back to previous OSD status [2]: Change to the selected Display Mode setting. [Up]: Scroll up the slider (When push the button on the top position, the slider shall go down to the bottom item) [Dn]: Scroll down the slider (When push the button on the bottom position, the slider shall go up to the top item) 4. Default = Standard 5.
9.under ECO mode, SRGB could be select and save the contrast and brightness of ECO 10.when adjust brightness and contrast value in current ECO mode , then change ECO mode and return current ECO mode ,the brightness and contrast value will be save Setup Menu Language Select English Set OSD language to English and keep in Language Select OSD French Set OSD language to French and keep in Language Select OSD German 1.
[Dn]: Scroll down the slider 2.
OSD V. Position 1. Adjust range = 0 to 100 2. Default = 50 3. Key button definition: [1]: Back to Setup Menu OSD [2]: Change to OSD H. Position OSD [Up]: Increase the OSD value setting (move OSD up) [Dn]: Decrease the OSD value setting (move OSD down) [Up]+[Dn]: Recall to default value OSD Time Out 5 Set OSD Time Out to 5 Seconds 15 Set OSD Time Out to 15 Seconds 30 1. Adjust range = 5, 15, 30, 60 Set OSD Time Out to 30 Seconds 60 2. Default = 15 Set OSD Time Out to 60 Seconds 3.
Sleep 30 Minutes Set time before going to Sleep mode = 30 Minutes 45 Minutes Set time before going to Sleep mode = 45 Minutes 60 Minutes 6. Adjust time range before going to sleep Set time before going to Sleep mode mode. Time range = 30, 45, 60, 120 = 60 Minutes (Minutes) and Off. 120 Minutes 7. Default = Off Set time before going to Sleep mode 8. When Sleep mode is triggered, the power of = 120 Minutes monitor will be turned off. Off 9.
at the center for 3 seconds. 5. Clean FIFO timing mode buffer 6. Execute Auto Image Adjust Note: Memory Recall should not effect on Language, Power Lock Settings or Input Priority The On-Screen Display (OSD) shall be an easy to use icon based menu through keypad OSD buttons or remote control unit. The unit shall leave the factory with all OSD controls set to their default values.
5.7 Upload firmware to MCU via VGA Cable 5.7.
5.7.2 Using Novatek ISP Tool Update FW: (1).Select “ISP”, Choose the corresponding firmware, load to MCU. (2).Choose the corresponding firmware, load to MCU, Select “Run”, start ISP. (3).When the picture show “End”, ISP finished.
6. Troubleshooting Flow Chart 6.1 Common Acknowledge z z z z z z z z z If you change the interface board, be sure that the U101, U103, U104 and U105 these four components also changed to the new I/F board because there was program inside. If not, please re-write EDID and upload firmware into U101 via VGA Cable. If you adjust clock and phase, please do it at the condition of Windows shut down pattern. If you confirm the R.G.B. color is normal or not, please do it under 16-grey scalar pattern.
6.2 No Power & Power LED Off No power Check primary Check circuit Check IC802, rectifier voltage if short C804, T801 Check F801, P801,,RT801, D801 Check pin5 of Check R833, R835, IC802 voltage R805, R834, R807 about 2.
6.
6.
6.5 Backlight can’t be turned on No raster? Yes LED Blue? Yes Backlight can’t be turned on.
6.
6.
6.
7.
8.
VGA-INPUT ViewSonic Corporation 85 VX2433wm-1 CONFIDENTIAL – DO NOT COPY VX2433wm-CN
DVI-INPUT ViewSonic Corporation 86 VX2433wm-1 CONFIDENTIAL – DO NOT COPY VX2433wm-CN
HDMI-INPUT ViewSonic Corporation 87 VX2433wm-1 CONFIDENTIAL – DO NOT COPY VX2433wm-CN
SCALER ViewSonic Corporation 88 VX2433wm-1 CONFIDENTIAL – DO NOT COPY VX2433wm-CN
AUDIO ViewSonic Corporation 89 VX2433wm-1 CONFIDENTIAL – DO NOT COPY VX2433wm-CN
ViewSonic Corporation 90 VX2433wm-1 CONFIDENTIAL – DO NOT COPY VX2433wm-CN
POWER SUPPLY ViewSonic Corporation 91 VX2433wm-1 CONFIDENTIAL – DO NOT COPY VX2433wm-CN
INVERTER SUPPLY ViewSonic Corporation 92 VX2433wm-1 CONFIDENTIAL – DO NOT COPY VX2433wm-CN
9.
MAIN BOARD - SILKCREEN BOTTOM ViewSonic Corporation 94 VX2433wm-1 CONFIDENTIAL – DO NOT COPY VX2433wm-CN
POWER BOARD - SILKSCREEN TOP ViewSonic Corporation 95 VX2433wm-1 CONFIDENTIAL – DO NOT COPY VX2433wm-CN
POWER BOARD - SILKSCREEN BOTTOM ViewSonic Corporation 96 VX2433wm-1 CONFIDENTIAL – DO NOT COPY VX2433wm-CN
KEYPAD FOR FUNCTION - SILKSCREEN TOP KEYPAD FOR POWER - SILKSCREEN TOP KEYPAD FOR FUNCTION - SILKSCREEN BOTTOM KEYPAD FOR POWER - SILKSCREEN BOTTOM ViewSonic Corporation 97 VX2433wm-1 CONFIDENTIAL – DO NOT COPY VX2433wm-CN
10.
EXPLODED PARTS LIST ( VX2433wm-1/VX2433wm-CN) ViewSonic Model Number: VS12324 Rev: 1a ITEM ViewSonic P/N 1 C-00009284 2 B-00009290 3 NA 4 E-00009253 5 NA 6 B-00009424 7 B-00009425 8 NA 9 E-00009255 10 C-00009287 11 C-00009285 12 C-00009286 13 NA 14 CB-00008927 15 NA 16 NA 17 B-00009289 18 CB-00008926 ViewSonic Corporation Ref.
PACKING PART LIST ( VX2433wm/VX2433wm-CN ) ViewSonic Model Number: VS12324 Rev: 1a Item ViewSonic P/N 1 CB-00008002 2 A-00008111 3 P-00009398 NA 4 NA 5 6 P-00009399 7 A-00008411 8 P-00009400 9 CB-00008190 10 CB-00008437 11 P-00009397 NA 12 13 P-00009396 NA 14 NA 15 ViewSonic Corporation 100 Ref.
11. Recommended Spare Parts List RECOMMENDED SPARE PARTS LIST (VX2433wm-1/VX2433wm-CN) ViewSonic Model Number: VS12324 Serial No. Prefix: VX2433wm-1 - R4F Serial No.
BOM LIST ( VX2433wm-1/VX2433wm-CN) ViewSonic Model Number: VS12324 Rev: 1a Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 ViewSonic P/N A-00008111 CB-00008437 CB-00008002 CB-00008190 NA NA NA P-00009397 P-00009398 P-00009399 P-00009400 P-00009396 NA NA NA NA NA A-00008411 NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA C-00009284 NA NA NA NA NA NA C-00009287 NA
Item ViewSonic P/N 58 C-00009286 59 NA 60 NA 61 NA 62 NA 63 NA 64 NA 65 NA 66 NA 67 NA 68 NA 69 NA 70 NA 71 NA 72 NA 73 NA 74 B-00009424 75 B-00009425 76 B-00009290 77 B-00009289 78 E-00009253 79 E-00009254 80 CB-00008926 81 NA 82 NA 83 CB-00008927 84 E-00009255 Ref.
* Reader’s Response* Dear Readers: Thank you in advance for your feedback on our Service Manual, which allows continuous improvement of our products. We would appreciate your completion of the Assessment Matrix below, for return to ViewSonic Corporation. Assessment A. What do you think about the content of this Service Manual? Unit Excellent Good Fair Bad 1. Precautions and Safety Notices 2. Specification 3. Front Panel Function Control Description 4. Circuit Description 5. Adjustment Procedure 6.
