Versatronik® 535 & 535D Solar Communication Gateway for solar controls BACnet IP Communication Document Applicable to: Versatronik 535 Solar/BACIP Wall Mount 704065 Versatronik 535D Solar/BACIP DIN Rail Mount 704066 Applicable Controls Resol Deltasol M Resol Deltasol BS Plus Resol Deltasol BS1/2/3/4 Resol Deltasol BX/BXL Resol Deltasol E/ES/BX/MX/SKSC3 Viessmann Vitosolic 200 Viessmann SCU 124 Viessmann SCU 224 Viessmann SCU 345 Technical, Installation and Configuration Information Cautionary Statement T
About these instructions ! Take note of all symbols and notations intended to draw attention to potential hazards or important product information. These include “WARNING”, “CAUTION” and “IMPORTANT”. See below. ! WARNING Indicates an imminently hazardous situation which, if not avoided, could result in death, serious injury or substantial product/property damage. KWE P/N 394043 Versatronik 535 Solar Gateway V1.
Important Regulatory and Installation Requirements Codes The installation of this unit must be in accordance with local codes. KWE P/N 394043 Versatronik 535 Solar Gateway V1.0 09/2013 Technical information subject to change without notice All electrical wiring is to be done in accordance with the latest edition of CSA C22,1 Part 1 and/ or local codes. In the U.S. use the National Electrical Code ANSI/NFPA 70.
Installation Mounting Versatronik Gateway—120VAC Unit KWE P/N 394043 Versatronik 535 Solar Gateway V1.0 09/2013 Technical information subject to change without notice 2 1 4 1 3 Mounting Steps 1. Mount Versatronik 535 Gateway in a convenient location near the solar control. Remove cover by loosening the two screws on either side of base to release the cover. 2. Fasten base to wall using field-supplied screws/fasteners. 3. Remove knockout and installed wire strain relief or box connector.
Installation Mounting Versatronik Gateway—24VAC DIN Rail Unit Mounting Steps 1. Mount Versatronik 535D Gateway onto DIN rail within an enclosure in a convenient location near the solar control. 2. Make all the necessary connections including the 24VAC power connection. 2 1. 2. 3. 4.
Connection Overview RJ45 Communication Cable Supplied Connection Overview KWE P/N 394043 Versatronik 535 Solar Gateway V1.0 09/2013 Technical information subject to change without notice 1. Cut UTP cable to 2m length. 2. Strip insulation and crimp plug on one end. 3. Strip other end, cut all wires but wire 1 and 2. 4. Strip wire 1 and 2. 5. Wires 1 and 2 used to make connections to the solar control.
Versatronik 535 Dial Setting Overview Rotary Dial Setting Setting Overview 1. The rotary dial setting on the Versatronik Gateways provides addressing information for systems that may utilize a number of Versatronik Gateways. Applications with the Versatronik 535 Solar with RESOL controls, it is not required to make adjustments to the rotary dial setting. It should be left in the factory default position setting of 0.
Connection Overview—120VAC Unit BACnet IP Communication connections to BMS: Example: Resol Deltasol BS Plus Connection Overview 1 Control sensor portion of control. 1 2 A CAT-5 cable is supplied with the Versatronik Solar Gateway. The RJ45 is plugged into the gateway and terminates into the control. 3 BMS connection.
Connection Overview—120VAC Unit BACnet IP Communication Connections to BMS: Example: Resol Deltasol M Connection Overview 1 Control sensor portion of control. V Bus 1 2 A CAT-5 cable is supplied with the Versatronik Solar Gateway. The RJ45 is plugged into the gateway and terminates into the control. 3 BMS connection.
Connection Overview—24VAC DIN Rail Unit BACnet IP Communication Connections to BMS: Example: Resol Deltasol BS Plus Connection Overview 1 Control sensor portion of control. 2 A CAT-5 cable is supplied with the Versatronik Solar Gateway. The RJ45 is plugged into the gateway and terminates into the control. 1 3 BMS connection.
Connection Overview—24VAC DIN Rail Unit BACnet IP Communication Connections to BMS: Example: Resol Deltasol M Connection Overview 1 Control sensor portion of control. 2 A CAT-5 cable is supplied with the Versatronik Solar Gateway. The RJ45 is plugged into the gateway and terminates into the control. V Bus 1 3 BMS connection.
Configuration of Gateway Configuring BACnet/IP Settings Connect your computer DIRECTLY to the BACnet interface of the gateway device, with no other devices attached (an isolated network). Either set your computer’s network connection to automatic IP Address (DHCP), or set your computer’s IP address to 192.168.88.90 (subnet mask 255.255.255.0) KWE P/N 394043 Versatronik 535 Solar Gateway V1.
Configuration of Gateway Continued BACnet Device Settings You can now reconfigure these settings according to your network requirements. Make sure that you press SAVE on every screen where you make changes. The new setting will not take effect until the Activate Configuration screen has been confirmed. These configuration pages can now be accessed through both the 192.168.88.89 Address, as well as the one you have selected. KWE P/N 394043 Versatronik 535 Solar Gateway V1.
BACnet Objects SCU224, SCU124, Deltasol BS Plus Deltasol 1/2/3/4 Deltasol-E Deltasol-ES Deltasol-BX Plus Deltasol-MX Deltasol-SKSC3 Analog Output 1 Controls temperature units - X X X X X X X X X Analog Input 1 Temperature Sensor 1 C or F X X X X X X X X X Analog Input 2 Temperature Sensor 2 C or F X X X X X X X X X Analog Input 3 Temperature Sensor 3 C or F X X X X X X X X X Analog Input 4 Temperature Sensor 4 C or F X X X X X X X X X Analo
KWE P/N 394043 Versatronik 535 Solar Gateway V1.
Technical Information 3 7 8 + #$ 9 % % ) ( ( ( ( * ' & KWE P/N 394043 Versatronik 535 Solar Gateway V1.
Technical Information 4 6 7 ! " # ! KWE P/N 394043 Versatronik 535 Solar Gateway V1.
KWE P/N 394043 Versatronik 535 Solar Gateway V1.0 09/2013 Technical information subject to change without notice KWE Technologies Group 750 McMurray Road Waterloo, Ontario, Canada N2V 2G5 Tel: (519) 747-5042 Fax: (519) 747-4448 www.kwe-tech.com info@kwe-tech.
