Install Instructions
Table Of Contents
- ProPress stainless approved fluids
- ProPress stainless approved gases
- Dimensional data
- ½" Stainless Steel, ASTM A312 flow rate, velocity, loss
- ¾" Stainless Steel, ASTM A312 flow rate, velocity, loss
- 1" Stainless Steel, ASTM A312 flow rate, velocity, loss
- 1¼" Stainless Steel, ASTM A312 flow rate, velocity, loss
- 1½" Stainless Steel, ASTM A312 flow rate, velocity, loss
- 2" Stainless Steel, ASTM A312 flow rate, velocity, loss
- 2½" Stainless Steel, ASTM A554 flow rate, velocity, loss
- 3" Stainless Steel, ASTM A554 flow rate, velocity, loss
- 4" Stainless Steel, ASTM A554 flow rate, velocity, loss
- Fitting friction loss equivalent length of tube (feet)
- MSS SP-58 or the maximum spacing and minimum rod sizes
- Minimum distance between press fittings
- ProPress standard jaws clearance requirements
- ProPress standard jaws clearance requirements between tube, wall, and floor
- ProPress compact jaws clearance requirements
- ProPress compact jaws clearance requirements between tube, wall, and floor
- ProPress rings dimensions
- ProPress rings with V1 actuator clearance requirements
- ProPress rings with V2 actuator clearance requirements
- ProPress rings with V1 actuator clearance requirements between tube, wall, and floor
- ProPress rings with V2 actuator clearance requirements between tube, wall, and floor
- ProPress rings with C1 actuator clearance requirements between tube, wall, and floor
- ProPress XL-C rings dimensions
- ProPress XL-C rings clearance requirements
- ProPress XL-C rings clearance requirements between tube, wall, and floor
- Minimum distance between existing soldered or brazed fitting and ProPress fitting
- Minimum distance between soldered fitting and ProPress fitting
- Minimum insertion depths for ProPress Stainless ½" to 2"
- Insertion depths for ProPress Stainless ½" to 2" no-stop couplings
- Minimum insertion depths ProPress Stainless 2½" to 4"
- Insertion depths for ProPress Stainless 2½" to 4" no-stop couplings
- About this Document
- Disclaimer
- Product Information
- Handling Instructions
- Installation Instructions
- Limited warranty
Product Information
16 of 56
IM-PP 599834 0320 ProPress Stainless
2.4.5.7 Viega Smart Connect Technology
Viega ProPress Stainless tubing is marked with important information
regarding the material conguration and manufacture of the tubing. It is
labeled with the following information along its entire length:
1 Manufacturer
2 Stock code
3 Specication standard
4 Material type
5 Nominal diameter x wall thickness
6 Manufacturing information
7 Date of manufacture
8 Batch code
9 Country of origin
VIEGA 87000 ASTM A 312 TP WWW 1/2" x 0.065" ET WLD XXX YYY ZZZ VVV
1 2 3 4 5 6 7 8 9
Viega Smart Connect technology provides the installer quick and easy
identication of an unpressed tting during a leak test. When the tting
is pressed, a secure, non-detachable, mechanical connection is created.
Smart Connect technology provides the installer with an easy way to see
connections that have not been pressed before putting the system into
operation.
Testing for leaks using Viega Smart Connect is not a
replacement for testing requirements of local codes and
standards. If testing with compressed air, it is necessary to
use an approved leak-detect solution.
3
Viega ProPress
connections are
fast, flameless, and
reliable.
1
Identify an unpressed
connection during
pressure testing
when water or air flows
past the sealing element.
2
Upon identification,
use the press tool
to press the fitting,
making a secure leak-
proof connection.
2.4.6 Marking on Tubing
It is the responsibility of the installer or any other parties
to adhere to all applicable local rules and regulations
governing the nature of the installation.