Submittal Package Viega ProPress® Systems Project Date Engineer Contractor Submitted by Approved by SM-PP 1120 ProPress Systems Date Approved by Date 1 of 31
Table of Contents Table of Contents Potable Water Hydronic Heating Chilled Water Compressed Air Nitrogen N2 Argon Low Pressure Steam Fire Protection 1 2 3 4 5 System Data Sheet_ ________________________________________ 3 ProPress Fitting Systems______________________________________ 3 Product Instructions________________________________________ 4 ProPress ½" to 2" Fittings_ ____________________________________ 4 ProPress 2½" to 4" Fittings____________________________________ 5 Engineering Specifications
System Data Sheet 1 System Data Sheet ProPress Fitting Systems Viega ProPress may only be pressed onto copper tube in accordance with ASTM B88 or B75. When pressing onto B88 copper tube, types K, L, and M may be used. Tempers O60 and O50, known as “soft copper”, are limited to nominal sizes ½" to 1¼". Temper H58, known as “hard copper”, may be used with nominal sizes ½" to 4". When pressing onto B75 copper tube, additional considerations apply. See Viega ProPress Copper Tube Compatibility Tech Data.
Product Instructions 2 Product Instructions ProPress ½" to 2" Fittings 1 2 3 4 7 8 9 10 Viega ProPress ½" to 2" Fittings For Hard Copper Tubing in ½" to 2" and Soft Copper Tubing in ½" to 1¼". 1 Cut the tube square using a displacement- type cutter or fine toothed saw. Note: Cut tubing a minimum of 4" away from the contact area of the vise to prevent possible damage to the tubing in the press area.
Product Instructions Product Instructions ProPress 2½" to 4" Fittings 1 2 3 4 5 66 7 8 9 10 11 12 Viega ProPress 2½" to 4" Fittings For Hard Copper Tubing. 1 Cut copper tubing at right angles using displacement-type cutter or fine-toothed steel saw. 2 Keep end of tubing a minimum of 4" away from the contact area of the vise to prevent possible damage to the tubing in the press area. 3 Remove burr from inside and outside of tubing to prevent cutting sealing element.
Engineering Specifications 3 Engineering Specifications ProPress Fitting System Part 1: General 1.1 Summary Copper tubing and fitting system for hot and cold water distribution systems, sprinkler and standpipe systems, and hydronic piping systems. 1.
Engineering Specifications 1.4 Quality Assurance A. Installer shall be a qualified installer, licensed within the jurisdiction, and familiar with the installation of ProPress copper press joint systems. B. ProPress copper press fittings shall be installed using the proper tool, actuator, jaws and rings as instructed by the press fitting manufacturer. C.
Engineering Specifications C. Press fitting: copper and copper alloy press fittings shall conform to material requirements of ASME B16.18 or ASME B16.22 and performance criteria of ASME B16.51 and IAPMO PS 117 (IAPMO PS 117 is not for B75). Sealing elements for press fittings shall be EPDM. Sealing elements shall be factory installed or an alternative supplied by fitting manufacturer. Press ends shall have Smart Connect® technology.
Engineering Specifications H. Pipe protection: provide protection against abrasion where copper tubing is in contact with other building members by wrapping with an approved tape, pipe insulation, or otherwise suitable method of isolation. I. Penetration protection: provide allowance for thermal expansion and contraction of copper tubing passing through a wall, floor, ceiling, or partition by wrapping with an approved tape or pipe insulation or by installing through an appropriately sized sleeve.
Dimensional Documents 4 Dimensional Documents ProPress Fittings Viega ProPress 90° Elbow Copper P x P - Model 2916 - Part No. " " - 77317 77022 77027 77032 77037 77042 Size (in) 1 1 ½x½ ¾x¾ 1x1 1¼ x 1¼ 1½ x 1½ 2x 2 A (in) L (in) 0.75 0.76 1.28 1.28 1.29 2.16 1.50 1.67 2.19 2.31 2.72 3.74 Size (in) 1 1 2½ x 2½ 3x3 4x4 A (in) L (in) 3.19 3.76 4.90 4.88 5.73 7.26 1 Viega ProPress 90° Elbow P x P - Model 0916XL - " Part No.
Dimensional Documents Viega ProPress 90° Street Elbow P x FTG - Model 0916.1XL - " Part No. 20638 20643 20648 Size (in) 1 2 2½ x 2½ 3x3 4x4 A (in) L (in) L1 (in) 3.19 3.76 4.90 4.88 5.73 7.26 4.80 5.63 7.13 - Viega ProPress 90° Reducing Elbow Copper P x P - Model 2916.3 Part No. 77325 77330 - Size (in) 1 2 ¾x½ 1x¾ A (in) A1 (in) L (in) L1 (in) 0.91 1.20 0.94 1.30 1.81 2.11 1.69 2.21 " " - Viega ProPress 90° Extended Street Elbow Copper P x FTG - Model 2947 Part No.
Dimensional Documents Viega ProPress Vent Elbow Zero Lead Bronze P x P x FPT - Model 2917.3ZL 2 Part No. 79635 79640 L1 Size (in) 1 2 3 ½ x ½ x ⅛ FPT ¾ x ¾ x ⅛ FPT A (in) A1 (in) A2 (in) L (in) 0.67 0.83 0.67 0.83 0.44 0.54 1.50 1.73 L1 (in) L2 (in) 1.50 1.73 0.71 0.81 A1 1 3 A A2 L L2 Viega ProPress 90° Hi Ear Elbow Zero Lead Bronze P x FPT - Model 2925.2ZL L1 Part No. A1 79205 L2 Size (in) 1 2 ½ x ½ FPT A (in) A1 (in) L (in) L1 (in) L2 (in) 0.94 0.57 1.77 1.10 1.
Dimensional Documents Viega ProPress 45° Elbow Copper P x P - Model 2926 - Part No. " " - 77607 77023 77028 77033 77038 77043 Size (in) 1 1 ½x½ ¾x¾ 1x1 1¼ x 1¼ 1½ x 1½ 2x 2 A (in) L (in) 0.30 0.36 0.47 0.58 0.65 0.86 1.04 1.26 1.38 1.61 2.08 2.44 Size (in) 1 1 2½ x 2½ 3x3 4x4 A (in) L (in) 1.48 1.73 1.96 3.18 3.70 4.63 Viega ProPress 45° P x P - Model 0926XL - Part No. " 20653 20658 20663 " - Viega ProPress 45° Street Elbow Copper P x FTG - Model 2926.1 - " Part No.
Dimensional Documents Viega ProPress Tee Copper P x P x P - Model 2918 - Part No.
Dimensional Documents Viega ProPress Tee Copper P x P x P - Model 2918 - Continued from previous page " Part No. " " - SM-PP 1120 ProPress Systems 15518 15513 15498 15508 15503 22228 15538 94777 94772 77487 77482 Size (in) 1 2 3 2 x 1¼ x 1¼ 2 x 1½ x ¾ 2 x 1½ x 1 2 x 1½ x 1¼ 2 x 1½ x 1½ 2 x 1½ x 2 2x2x½ 2x2x¾ 2x2x1 2 x 2 x 1¼ 2 x 2 x 1½ A (in) A1 (in) A2 (in) L (in) 0.94 0.70 0.82 0.94 1.13 1.38 0.54 0.79 0.91 1.04 1.13 1.84 1.25 1.45 1.55 1.65 1.89 0.54 0.79 0.91 1.04 1.13 1.33 1.
Dimensional Documents Viega ProPress Tee P x P x P - Model 0918XL - Part No.
Dimensional Documents Viega ProPress Tee Zero Lead Bronze P x P x FPT - Model 2917.2ZL L1 A1 Part No. 1 L A 3 A L 2 79580 79585 79590 79595 79760 79765 79770 79775 79780 79785 79790 79795 Size (in) 1 2 3 ½ x ½ x ½ FPT ¾ x ¾ x ¼ FPT ¾ x ¾ x ½ FPT ¾ x ¾ x ¾ FPT 1 x 1 x ½ FPT 1 x 1 x ¾ FPT 1¼ x 1¼ x ½ FPT 1¼ x 1¼ x ¾ FPT 1½ x 1½ x ½ FPT 1½ x 1½ x ¾ FPT 2 x 2 x ½ FPT 2 x 2 x ¾ FPT A (in) A1 (in) L (in) L1 (in) 0.79 0.67 0.79 0.91 0.79 0.91 0.83 0.95 0.87 0.94 0.98 1.06 0.69 0.79 0.88 0.59 1.04 1.
Dimensional Documents Viega ProPress Adapter P x MPT - Model 0911XL Part No. 20823 20828 20838 Size (in) 1 2 2½ x 2½ MPT 3 x 3 MPT 4 x 4 MPT A (in) L (in) 2.76 2.84 3.10 4.45 4.80 5.46 " - Viega ProPress Adapter Zero Lead Bronze FTG x MPT - Model 2911.1ZL Part No. 1 2 Size (in) 1 2 ½ x ⅜ MPT ½ x ½ MPT ½ x ¾ MPT ¾ x ½ MPT ¾ x ¾ MPT 1 x ¾ MPT 1 x 1 MPT 1¼ x 1¼ MPT 1½ x 1½ MPT 2 x 2 MPT 79375 79380 79385 79390 79395 79400 79405 79410 79415 79420 L L (in) 1.75 1.95 2.05 1.93 2.05 2.05 2.22 2.
Dimensional Documents Viega ProPress Adapter P x FPT - Model 0912XL Part No. - 20819 20829 20839 Size (in) 1 2 2½ x 2½ FPT 3 x 3 FPT 4 x 4 FPT A (in) L (in) 1.53 1.84 2.09 4.15 4.82 5.55 A (in) L (in) 1.10 1.22 1.30 1.26 1.28 1.35 1.33 1.65 1.50 1.88 2.13 1.54 1.75 1.83 1.79 1.83 1.99 1.99 2.19 2.19 2.56 2.95 A (in) L (in) 0.29 0.43 0.23 0.33 0.35 0.45 0.49 0.49 0.59 0.59 0.73 0.59 1.61 1.83 1.56 1.73 1.87 1.97 2.26 2.38 2.36 2.87 2.68 3.
Dimensional Documents Viega ProPress Adapter Flange Zero Lead Bronze P x Flange - Model 2959.5ZL % L Part No. Size (in) 1 79680 1 79685 1¼ 79690 1½ 79695 2 A (in) L (in) b (in) D (in) k (in) d (in) 1.85 1.73 1.65 2.09 2.76 2.76 3.07 3.66 0.84 0.84 0.84 0.84 4.33 4.53 4.92 5.91 3.11 3.50 3.86 4.76 0.63 0.63 0.63 0.75 E C " - Viega ProPress Adapter Flange P x Flange - Model 0959.5XL " - Part No. 20853 20858 Size (in) 1 2½ 3 A (in) L (in) b (in) k (in) D (in) d (in) 1.09 1.
Dimensional Documents Viega ProPress Cap Copper P - Model 2956 Part No. 77712 77717 77722 77727 77732 77737 " - Size (in) 1 ½ ¾ 1 1¼ 1½ 2 A (in) L (in) 0.79 0.94 0.99 1.20 1.49 1.69 0.92 1.07 1.11 1.32 1.62 1.81 Size 1 2½ 3 4 A (in) L (in) 0.39 0.39 0.39 2.11 2.36 2.76 Size (in) 1 ½ ¾ 1 1¼ 1½ 2 A (in) L (in) 1.19 1.34 1.83 1.64 2.13 2.07 2.84 3.15 3.65 3.69 4.96 5.22 A (in) L (in) 0.91 0.96 1.31 1.27 1.77 1.65 2.27 2.42 2.88 2.97 3.87 3.
Dimensional Documents Viega ProPress Union Zero Lead Bronze P x MPT - Model 2965ZL Part No. " - 79730 79735 79740 79745 79750 79755 Size (in) 1 2 ½ x ½ MPT ¾ x ¾ MPT 1 x 1 MPT 1¼ x 1¼ MPT 1½ x 1½ MPT 2 x 2 MPT A (in) L (in) 1.86 2.00 2.54 2.49 3.05 2.99 2.69 2.90 3.45 3.52 4.47 4.57 A (in) L (in) 0.88 1.11 1.00 0.97 1.01 1.26 2.24 2.57 2.57 2.68 3.11 3.53 A (in) L (in) 0.39 0.63 0.91 0.73 1.57 1.87 2.14 2.04 A (in) L (in) 0.12 0.20 0.16 0.14 0.14 0.14 1.61 2.01 1.97 2.20 2.99 3.
Dimensional Documents Viega ProPress Coupling with Stop P x P - Model 0915XL Part No. 20728 20733 20738 " - Size (in) 1 1 2½ x 2½ 3x3 4x4 A (in) L (in) 0.95 0.98 1.06 4.33 4.92 5.79 Viega ProPress Coupling No Stop Copper P x P - Model 2915.3 Part No. 78172 78177 78182 78187 78192 78197 - Size (in) 1 1 ½x½ ¾x¾ 1x1 1¼ x 1¼ 1½ x 1½ 2x 2 L (in) Size (in) 1 1 ½x½ ¾x¾ 1x1 1¼ x 1¼ 1½ x 1½ 2x 2 L (in) Size (in) 1 1 2½ x 2½ 3x3 4x4 L (in) 1.61 2.01 1.97 2.20 2.99 3.
Dimensional Documents Viega ProPress Reducer Copper P x P - Model 2915.2 Part No. 78147 15603 78152 15593 78157 18473 15588 78162 18468 15608 22328 78167 " - Size (in) 1 2 ¾x½ 1x½ 1x¾ 1¼ x ¾ 1¼ x 1 1½ x ¾ 1½ x 1 1½ x 1¼ 2x¾ 2x1 2 x 1¼ 2 x 1½ A (in) L (in) 0.42 0.71 0.48 0.70 0.55 0.98 0.74 0.50 1.54 1.29 0.81 0.74 2.07 2.36 2.29 2.64 2.48 3.33 3.07 2.96 4.02 3.78 3.43 3.75 Size (in) 1 2 2½ x 1 2½ x 1¼ 2½ x 1½ 2½ x 2 3 x 1½ 3x2 3 x 2½ 4x2 4 x 2½ 4x3 A (in) L (in) 1.76 1.61 1.52 1.41 1.78 1.
Dimensional Documents Viega ProPress Reducer Zero Lead Bronze FTG x P - Model 2915.1ZL Part No. 79850 79855 79860 Size (in) 1 2 1½ x ½ 2x½ 2x¾ A (in) L (in) 1.95 2.38 2.42 2.78 3.21 3.33 Size (in) 1 2 2½ x 1 2½ x 1¼ 2½ x 1½ 2½ x 2 3 x 1¼ 3 x 1½ 3x2 3 x 2½ 4x2 4 x 2½ 4x3 A (in) L (in) 3.61 3.47 3.41 2.35 3.96 3.91 2.98 2.76 4.58 4.45 4.17 4.52 4.51 4.84 3.94 5.00 5.34 4.57 4.45 6.17 6.15 6.14 " - Viega ProPress Reducer FTG x P - Model 0915.1XL Part No.
Dimensional Documents Viega ProPress Ball Valve Zero Lead Bronze P x P - Model 2971.3ZL - Part No. 79923 79928 79933 79938 79943 79948 ) " " - - Size 1 1 ½x½ ¾x¾ 1x1 1¼ x 1¼ 1½ x 1½ 2x2 A (in) A1 (in) L (in) L1 (in) L2 (in) H (in) 0.75 0.85 1.02 1.14 1.46 1.73 0.75 0.87 1.06 1.12 1.25 1.47 1.57 1.75 1.93 2.17 2.87 3.31 1.57 1.77 1.96 2.15 2.67 3.05 4.57 4.57 5.75 5.75 6.12 6.12 1.97 2.09 2.46 2.67 3.02 3.32 Viega ProPress Ball Valve Zero Lead Bronze P x FPT - Model 2971.
Dimensional Documents Viega ProPress Ball Valve Bronze/Brass P x FPT - Model 2973.1 - Part No. Size (in) 1 x FPT 24030 ½x½ 24035 ¾x¾ 24040 1x1 ) '15 - " A (in) A1 (in) L (in) L1 (in) L2 (in) H (in) 0.83 0.95 1.18 0.63 0.70 0.93 1.58 1.86 2.09 1.16 1.26 1.59 3.94 4.72 4.72 1.69 1.97 2.13 A (in) A1 (in) L (in) L1 (in) L2 (in) H (in) 0.83 0.95 0.85 0.94 1.58 1.86 1.30 1.39 3.89 4.72 1.67 1.97 " - Viega ProPress Ball Valve Bronze/Brass P x Hose - Model 2973.3 - Part No.
Dimensional Documents Butterfly Valve - Model 2873.81 " # ( $ * ' % & Part No. 22074 22075 ) Size (in) 2½ 3 A (in) 6.50 7.28 B (in) 7.40 7.64 C (in) 2.17 2.80 D (in) 0.43 0.67 E (in) 1.81 1.81 F (in) 2.64 2.82 G (in) 5.35 5.59 H (in) 5.20 7.01 I (in) 5.51 5.98 D (in) 0.91 E (in) 2.05 F (in) 3.62 G (in) 6.42 H (in) 8.27 I (in) 7.48 Butterfly Valve - Model 2873.81 " # ( * $ * ' & Part No. 22076 % ) Size (in) 4 SM-PP 1120 ProPress Systems A (in) 9.06 B (in) 8.
Dimensional Documents Viega ProPress Automatic Recirculation Regulating Valve Zero Lead - Model 2981.3ZL Part No. 79901 C Size (in) 1 A (in) 3.66 B (in) 3.43 C (in) 1.09 D (in) 0.79 B D A Shower Valve - Model 2842.5 - Part No. 93516 Stub Out (in) ½ A (in) 4.75 L (in) 5.625 Part No. 93517 Stub Out (in) ½ A (in) 4.75 L (in) 5.875 " Shower Valve - Model 2842.
Dimensional Documents Viega ProPress Cross-Over Copper P x P - Model 2928 Part No. ) 77742 77747 Size (in) 1 1 ½x½ ¾x¾ A (in) L (in) H (in) 3.62 4.49 5.12 6.30 0.77 0.90 " - Viega ProPress Stem Extension Brass - Model 2973.96* " : 煦/ : Part No. Valve Size (in) 23449 ½ 23451 ¾, 1 23453 ¼, 1½, 2 M (in) 0.669 0.787 1.023 N (in) 0.984 1.102 1.417 A (in) 3.937 4.724 6.220 Y (in) 2.224 2.460 2.657 y (in) 1.043 1.082 0.807 *For use with Model 2973, 2973.1, and 2973.3 Valves 煦.
Limited Warranty 5 Limited Warranty Viega ProPress Fitting and Valves Subject to the conditions and limitations in this Limited Warranty, Viega LLC (VIEGA) warrants to wholesalers and licensed plumbing and mechanical contractors in the United States and Canada that its ProPress fittings, when properly installed in non-industrial and non-marine applications and under normal conditions of use, will be free of failure from manufacturing defect for a period of fifty (50) years from date of installation and th
