AU-DVRS-04LH User's Manual DIGITAL VIDEO RECORDER
Installation and Precaution 1. Warning This unit is designed, to be used in indoor condition, to reduce fire and shock hazard, do not expose the unit to rain or moisture. Prevent any foreign object or liquid to enter the unit. In case, there is any foreign object or liquid go inside the unit, cut off the power immediately, and call for a qualified service person to inspect and test the unit, before putting the unit back to operation. Do not touch any part of the unit with wet hands.
Delivery Packing Checklist This unit is packed with the following accessories, please kindly check immediately after unpacking the box ： 1、 1 no. of power supply cord 2、 1 no. of operating manual 3、 1 no.
Index FRONT PANEL………………………………………………...6 REAR PANNEL……………………………………………….. 8 HARD DISK INSTALLATION.................................................. 9 VOLTAGE OUTPUT & SENSOR INPUT AND ALARM OUTPUT CONNECTION……………………………………..10 POWER ON AND OFF………………………………………...11 1.POWER ON……………………………………………………………………………. .11 2.POWER OFF…………………………………………………………………………… .11 SYSTEM SETUP………………………………………………12 1、TO ENTER MENU ..........................................................................................................
1.1-3Weekly .......................................................... 1.2Event Recording .................................................... 1.2-1Motion Detection .................................................. 1.2-2 Sensor Detection .................................................. 1.3Repeat Recording.................................................... 1.4Recording Speed (Frame Rate) ........................................ 1.5 Compression Rate (Recording Quality) ..................................
4-2、USB Backup.............................................................................................. 34 5．Status Indication .................................................... 35 6．SPOT Display ...................................................... 35 7．Hard disk format .................................................... 35 NETWORK SOFTWARE OPERATION ................ 37 1、GRAPHIC USER INTERFACE INTRODUCTION ................................. 37 2、CONNECT AND DISCONNECT.............................
Front Panel 1.Power Button Turn the unit on or off. 2.Digits Buttons Change time, password, and input IP address 3.Menu Button Go to the top level of the menu tree 4.Setup Button Other operation Menu 5.Channel Select Button Select the channel. Toggle the screen between QUAD, 1,2,3 or 4 6.SPOT Button Put the display mode to Spot Mode. Toggle the screen between Quad, Channel 1.2.3 or 4, under Spot viewing 7.STATUS Button System status indication 8.Power LED Power on/off indication 9.
18.Enter Button Confirm of the data input 19.Up Button Up action for menu tree navigation, pan/tilt etc.. 20.Left Button Left action for menu tree navigation, pan/tilt control etc.. 21.Right Button Right action for menu tree navigation, pan/tilt control etc.. 22.Down Button Down action for menu tree navigation, pan/tilt control etc.. 23.Search Button Go to "Search" item under the menu tree.
Rear Panel 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15.
Hard disk installation This unit is delivered without the hard disk by default. Please contact our local agent or regional representative, so they provide qualified service personnel to install hard disk to suit for your storage and video image retention requirement. The unit is not operational before installation of hard disk. The maximum number of IDE hard disks, which can be installed in this unit is four.
Voltage Output & Sensor Input and Alarm Output Connection Sensor Input This unit has 4 numbers of isolated Sensor input to take voltage free relay outputs from peripheral alarm sensors. These Sensor inputs are protected from high voltage input from outside, by providing the opt-isolated design Sensor Input Setup ： Set the sensor type to “no(normal open)” or “nc(normal close)”. This unit need to input external power supply to connect each sensor.
Power ON and OFF 1、Power On Before the first time of turning on the unit for operation, please make sure all points listed in the “Installation and Precaution” section has been studied and followed. Double check all connections to the unit is correct, and power supply connection to the unit is proper.
System Setup The unit should be configured using the menu, to tailor suit the unit for specific site operation, if not, the unit will operate under ex-factory default settings. 1、To enter SETUP Press “Setup” button on remote controller or front panel to go into Setup Menu. 2、 Menu and screen prompt operation After entering the menu, operator can navigate the items by using the up button and down button, either on front panel or remote controller, to highlight the items on the present level of the menu.
The unit’s system password is a combination of numeric digital between 0 and 9. Numeric key on remote controller or front panel can be used to enter the password. On entering of the system password, for security reasons, the on-screen indication is represented by “*”. The ex-factory default system password is “0000”.
After inputting the new system password, the screen prompt will request to enter the new password again to reconfirm. 1.2Language Setting By highlighting “Language” item and press “Enter”, the screen prompt will be changed as follows: Korean English Chinese simplified Chinese traditional Spanish French Japanese Operator can highlight the desired language and press “Enter” to confirm the selection. 1.
Select one of the date mode, and confirm by pressing “Enter”. Example) dd/mm/yy ---- Day/Month/Year 1.5Time Indication Position Setting (OSD format) After selecting this item, the screen prompt is as follows: 〔OSD〕 TTTT(W) BBBB(W) TTBB(W) BBTT(W) OFF TTTT(B) BBBB(B) TTBB(B) BBTT(B) One of the eight modes of time indication position should be highlighted and confirmed by pressing “Enter”.
Recording Setup 1、To enter the menu Press “SETUP” button on remote controller or front panel to go into SETUP Menu. 2、Menu and screen prompt operation After entering the menu, operator can navigate the items by using the up button and down button, either on front panel or remote controller, to highlight the items on the present level of the menu. To go down one level to the highlighted item under the present level of the menu, “Enter” key should be pressed either on front panel or remote controller.
1.1Scheduled Recording Under this item, the screen prompt is as follows: One Time Daily Weekly 1.1-1One Time Under “One Time”, the screen prompt is as follows: 〔Start〕 mm/dd/yy hh:mm 〔End〕 mm/dd/yy hh:mm 01/10/04 10:00 01/10/04 19:55 Use numeric key to enter the start and end time and date for the one-shot scheduled recording period of time. 1.
Sunday Monday Tuesday Wednesday Thursday Friday Saturday Select one of the day under a week, by highlight a day (e.g. Sunday) and press “Enter”. The screen prompt will be changed as follows: 〔Sunday〕 * Start (hh:mm) * End (hh:mm) * Start (hh:mm) * End (hh:mm) * Start (hh:mm) * End (hh:mm) 09:00 11:30 13:00 18:00 13:00 18:00 Use numeric key to enter the start and end time and date for the one-time scheduled recording period of time. Three individual period of time can be inputted for one day.
〔Motion Detection〕 #1 STD SEN #2 STD SEN #3 STD SEN #4 STD SEN 〔OFF〕 〔OFF〕 〔OFF〕 〔OFF〕 Press Up or down to select the camera number, and left or right to select the motion detection recording property. Motion Detection: The “Standard”, “Sensitive” or “Off” fields, is to indicate whether the motion detection for that camera is activated or not, if activated which level of sensitivity is set. Sensitivity ：Two levels, “Standard” or “Sensitive”.
1.3Repeat Recording Under this “Repeat Record” item, the screen prompt is as follows: 〔Repeat Record〕 ON OFF If the “Repeat Record” is activated, then the on-line hard disk space will be acting as an FIFO (First In First Out) buffer, old images will be erased automatically. No operator intervention will be required on hard disk being full. In contrast, if the “repeat Record” is not activated, then operator will be prompted on hard disk being full, no old image will be erased.
〔Compression Rate〕 Standard High-1 High-2 Operator can select one of the three quality level and press “Enter” to confirm. For determination of quality of recording to be selected, operator should consider the hard disk space available and desirable retention period of video clips on local hard disk(s). Please refer to the following benchmarking to estimate one’s need on retention period and hard disk space. ☞ Storage per hour (each Channel) – Standard is 225MB / High-1 is 450MB /High-2 is 675MB 1.
NO 96 97 98 99 100 101 102 103 104 105 106 107 108 DATE 01/10 01/10 01/10 01/10 01/10 01/10 01/10 01/10 01/10 01/10 01/10 01/10 01/10 TIME 11:30 12:00 12:31 13:05 13:30 15:00 15:31 17:02 17:09 17:50 18:21 18:50 20:00 〈PgUp/Dn〉 UNLOCK UNLOCK LOCKED UNLOCK UNLOCK LOCKED UNLOCK UNLOCK UNLOCK UNLOCK UNLOCK UNLOCK UNLOCK FILE NAME S040110110000U S040110120030U S040110123100U E040110130540U E040110133000L S040110150032U S040110153150L E040110170250U S040110170920U S040110175000U S040110182110U S0401101850430U
Hardware Setup 1、To enter the menu Press “SETUP” button on remote controller or front panel to go into SETUP Menu. 2、Menu and screen prompt operation After entering the menu, operator can navigate the items by using the up button and down button, either on front panel or remote controller, to highlight the items on the present level of the menu. To go down one level to the highlighted item under the present level of the menu, “Enter” key should be pressed either on front panel or remote controller.
1.1PTZ Camera Setting Under this item, the screen prompt is as follows: 〔PTZ camera model〕 CNB-102N PELCO D protocol Operator can select the PTZ protocol to be employed by this unit to match with the PTZ camera connected. ☞ Note: the list of supported PTZ protocol will be expanding, please contact our local agent or regional representative for details. 1.
1.3-1Sensor Type Under this item, the screen prompt is as follows: 〔Sensor type〕 * Sensor 1 * Sensor 2 * Sensor 3 * Sensor 4 NC NC NC NC 〔NO〕 〔NO〕 〔NO〕 〔NO〕 Use up and down keys to highlight individual alarm input, and use left or right keys to select the type of alarm input. Type of Sensor input, can be NO (normally open) or NC (normally close). 1.
Use up and down keys to highlight individual sensor input, and use left or right keys to select the condition of alarm output. Type of sensor input, can be NO (normally open) or NC (normally close). ☞ Default setting by factory “ON” 1.3-4Alarm Out Period Under this item, the screen prompt is as follows: 〔Alarm Period〕 30 sec 01 min 03 min 10 min Manual off This alarm time item, is to configure the alarm output activation duration on associated alarm being triggered.
If static IP is selected, then the screen prompt will be changed as follows: IP Address : 192.168.001.201 GATEWAY : 192.168.001.001 NETWORK : 255.255.255.000 Key in the static IP address, Gateway and Sub-Net address using the numeric keys on remote controller. This network setting is for client software operation over the network. 1.
Operator will be prompted to enter the new password again to re-confirm. 1.5Storage Setting Under this item, the screen prompt is as follows: Secondary Third Fourth IEEE 1394 YES YES YES YES 〔NO〕 [NO] [NO] 〔NO〕 FORMAT FORMAT FORMAT FORMAT This unit can support 4 numbers of internal hard disk in Maximum. For the first master hard disk, the formatting and recognizing will be started automatically.
Recording Search / Operation Recording search is one of the key functions of a digital video recorder. Video clip searching can be according to different kinds of information, like time, alarm and event.
Select file and press “Enter” key to confirm and start the searching. Press the “CH SEL” button to expand channel 1, channel 2, channel 3 or channel 4. Press 5times to return to the 4-split screen.
After correct password is entered by using numeric keys on front panel or remote controllers, then the recording of the unit is manually started. This can be actively confirmed by observing the “REC” indication on screen.
“After “Pause” is pressed, pressing the rewind key will switch the playback between x1/2, x1/4, x1/8 slow motion rewind playback mode. Pressing “stop” button will stop the playback (without freeze the screen on latest frame). Other Operation The “Other operation Menu” items is showed below ： PAN/TILT ZOOM/FOCUS AUDIO BACKUP STATUS 1、Pan Tilt Control Press “Enter” when the “Pan/Tilt” item is highlighted, then the following screen will appear ： CAM1 PAN/TILT EXIT 4.3.
1.2 Camera selection By pressing “Pan/Tilt” button on the remote controller or the “Enter” Key on the front panel, camera selection of CAM2,3 or 4 can be done. Once CAM2, 3 or 4 is selected, pan/tilt control can be achieved as per section 1.1. 2、Zoom / Focus control By selecting “Zoom/Focus” item under the menu, the screen prompt will be as follows: CAM1 ZOOM/FOCUS EXIT 2.1.
4．Backup By selecting “Backup” item under the menu, the screen prompt will be as follows: 〔Backup〕 IEEE 1394 USB 4.1. IEEE1394 Backup Select the IEEE 1394 item by pressing “Enter” when the item is highlighted. The screen prompt will be as follows: 〔IEEE 1394 Backup〕 Partially Entirely 4.1-1. IEEE 1394 Single Period Backup Select “Partially” by pressing “Enter” when the item is highlighted.
Press the numeric keys to input the start and end time and date of the period of data to be backed up to USB device. The USB backup will be started immediately, on completion of the backup, this menu item will be quitted automatically. 5．Status Indication By pressing “Enter” when the “Status” item is highlighted, the detailed system status will be displayed. The following is a sample display of the system status of this unit. TIME VERSION : 10 : 30 : 15 : DRIVER = 1.16.0002 OS = (03/12/24) APP = 4.0.
☞ If there is no hard disk installed yet, press “Exit” button. If there is hard disk installed already, press “Enter” to start formatting of the hard disk. WARNING : HDD does not exist, or, is not initialized !! If HDD does not exist, press 〈 EXIT〉 If HDD is not initialized, press〈 ENTER〉 FDISK FORMAT MADIRS OK OK OK Initialized completed, Press 〈 EXIT〉 to power off ☞ Upon formatting finished, “Exit” button should be pressed, such that the unit will be shut down automatically and restarted again.
Network Software Operation Client software is provide with the unit for operator to operate the unit via remote network connection.， Remote operation via this client software can include remote monitoring, remote playback, remote control and remote backup etc..
password (Network password as assigned on the DVR end). Click on OK to continue. Note: One DVR allow up to five user to log in simulataneously via the internet or LAN same time. 2-2、Disconnect Click on the disconnect button, the following dialogue box will pop up. Click “OK” to confirm disconnect.： 3、Live Display After connecting, the live image will be displayed automatically.
“▲” to control the direction, and use ZOOM, FOCUS“+”， “-”key to control the zoom in/out and focus near/far functions. Warning: If the camera control function is left idling for more than one minute, then the control privileges will be expired and handed over to other user. 5、Backup Press the “BACKUP” button It appears as follows: Choose the list up with All list or SET Date to find and Enter the correct system password A list of recorded files appears Choose the required file to back up.
6、 Open File After clicking the “Open” button, the following dialogue box will pop up: Select the desired file Click “OK”. Playback will start automatically. Backed-up files are saved in the “Mpeg Files” folder, Choose the required file and press Open to open the file. File notation illustration 0312171530.MPG --- File start time is 15:30 17 December 2003. Press “Stop” will stop the playback. Press “Pause” will freeze the playback at the last frame.
8.
SPECIFICATION Description Signal Format PAL/NTSC Video input 1.0V p-p/75Ω，BNC，4ch Video output 1.
