VideoWave2 Setup Guide Covers_AIM.fm Page 1 Wednesday, January 25, 2012 11:34 AM Setup Guide Guía de instalación Guide d’installation ©2012 Bose Corporation, The Mountain, Framingham, MA 01701-9168 USA AM352276 Rev.
00.Marley_Setup.book Page 2 Tuesday, January 10, 2012 8:47 AM Tab 8, 16 Tab 7, 15 Tab 6, 14 Tab 5, 13 Tab 4, 12 Tab 3, 11 Tab 2, 10 English SAFETY INFORMATION Please read this guide Please take the time to follow the instructions in this setup guide carefully. They will help you set up and operate your system properly and enjoy its advanced features. Please save all safety and operating instructions, including this guide, for future reference.
00.Marley_Setup.book Page 3 Tuesday, January 10, 2012 8:47 AM English Tab 2, 10 Tab 3, 11 Tab4, 12 Tab 6, 14 Tab 5, 13 Tab 7, 15 Tab 8,16 SAFETY INFORMATION • Allowing children to push, pull, or climb on the monitor may cause it to tip over, possibly resulting in personal injury or death. – For safety and greater stability, installation of the included anti-tip straps is recommended. – Be sure to install both anti-tip straps according to the instructions on page 11.
00.Marley_Setup.book Page 4 Tuesday, January 10, 2012 8:47 AM Tab 8, 16 Tab 7, 15 Tab 6, 14 Tab 5, 13 Tab 4, 12 Tab 3, 11 Tab 2, 10 English SAFETY INFORMATION Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
00.Marley_Setup.book Page 5 Tuesday, January 10, 2012 8:47 AM English TAB 2 TAB 3 TAB 4 WELCOME Product overview . . . . . . . . . . . . . . . . . . . . . . . . . The setup process . . . . . . . . . . . . . . . . . . . . . . . . PHYSICAL SETUP Monitor placement and connections . . . . . . . . . . Monitor placement recommendations . . . . . . . Placing the monitor with stand . . . . . . . . . . . . . Installing the anti-tip straps . . . . . . . . . . . . . . . Wall-mounting the monitor . . . . . . . .
00.Marley_Setup.
00.Marley_Setup.book Page 7 Tuesday, January 10, 2012 8:47 AM English Tab 2, 10 Tab 3, 11 Tab4, 12 Tab 6, 14 Tab 5, 13 Tab 7, 15 Tab 8,16 WELCOME Thank you The setup process ® ® Thank you for purchasing the Bose VideoWave entertainment system. This guide provides you with step-by-step instructions for setting up your new entertainment system. Note: Professional installation is recommended.
00.Marley_Setup.book Page 8 Tuesday, January 10, 2012 8:47 AM Tab 8, 16 Tab 7, 15 Tab 6, 14 Tab 5, 13 Tab 4, 12 Tab 3, 11 Tab 2, 10 English PHYSICAL SETUP Monitor placement and connections The monitor can be placed on furniture using the attached stand or it can be mounted on a wall. WARNING: The monitor weighs about 119 lbs. (59 kg). To prevent personal injury, a two-person lift is required. CAUTION: DO NOT mount or place the monitor in a recessed area or cabinet.
00.Marley_Setup.book Page 9 Tuesday, January 10, 2012 8:47 AM English Tab 2, 10 Tab 3, 11 Tab4, 12 Tab 6, 14 Tab 5, 13 Tab 7, 15 Tab 8,16 PHYSICAL SETUP Here is what you need from Box 1: Placing the monitor with stand Before you place the monitor, you must attach the stand. 11 1. Unpack the stand, screws, and monitor. 2. Lower the monitor onto the stand, carefully lining up the holes in the bottom of the monitor with the supports on the stand.
00.Marley_Setup.book Page 10 Tuesday, January 10, 2012 8:47 AM Tab 8, 16 Tab 7, 15 Tab 6, 14 Tab 5, 13 Tab 4, 12 Tab 3, 11 Tab 2, 10 English PHYSICAL SETUP 3. On the rear panel of the monitor, firmly pull out on the bottom of the connector cover to remove it. 5. Place the monitor on a stable, flat surface capable of supporting the combined weight of the stand and the monitor (150 lbs.). Connector cover Monitor 4.
00.Marley_Setup.book Page 11 Tuesday, January 10, 2012 8:47 AM English Tab 2, 10 Tab 3, 11 Tab4, 12 Tab 6, 14 Tab 5, 13 Tab 7, 15 Tab 8,16 PHYSICAL SETUP 7. Route both cords through the leg of the stand and re-attach the connector cover. Installing the anti-tip straps It is important that you install both straps according to the following instructions. WARNING: Do not use the anti-tip straps for any application other than the one specified in this setup guide.
00.Marley_Setup.book Page 12 Tuesday, January 10, 2012 8:47 AM Tab 8, 16 Tab 7, 15 Tab 6, 14 Tab 5, 13 Tab 4, 12 Tab 3, 11 Tab 2, 10 English PHYSICAL SETUP 3. Locate the two wall studs closest to the straps. Each strap should be attached to the wall stud closest to it. DO NOT attach both straps to the same stud. min CAUTION: The included screws are for use only into wood-studded wall constructions with one-inch (max.) drywall.
00.Marley_Setup.book Page 13 Tuesday, January 10, 2012 8:47 AM English Tab 2, 10 Tab 3, 11 Tab4, 12 Tab 6, 14 Tab 5, 13 Tab 7, 15 Tab 8,16 PHYSICAL SETUP 7. Push monitor back to within 1-4 in. (2.5-10 cm) from the wall. Wall-mounting the monitor ® The VideoWave system is compatible with any VESA certified bracket that uses a 400 mm x 400 mm screw pattern. The panel itself without the stand weighs 119 lbs. (59 kg), so the mount must be able to support that weight.
00.Marley_Setup.book Page 14 Tuesday, January 10, 2012 8:47 AM Tab 8, 16 Tab 7, 15 Tab 6, 14 Tab 5, 13 Tab 4, 12 Tab 3, 11 Tab 2, 10 English PHYSICAL SETUP 3. Attach the monitor cable and AC power cord to the monitor as shown. 4. Attach the wall-mounting brackets (not included) to the wall and monitor according to the instructions included with the wall bracket. 5. Lift the monitor out of the packing. Monitor cable AC power cord Note: You do not need to re-attach the connector cover.
00.Marley_Setup.book Page 15 Tuesday, January 10, 2012 8:47 AM English Tab 2, 10 Tab 3, 11 Tab4, 12 Tab 6, 14 Tab 5, 13 Tab 7, 15 Tab 8,16 PHYSICAL SETUP Control console placement and connections Here is what you need from Box 1: 11 Power supply Power supply AC power cord 1. Place the control console on a flat, stable surface near the monitor. • Make sure the supplied monitor cable (3 m) can reach from the console to the monitor.
00.Marley_Setup.book Page 16 Tuesday, January 10, 2012 8:47 AM Tab 8, 16 Tab 7, 15 Tab 6, 14 Tab 5, 13 Tab 4, 12 Tab 3, 11 Tab 2, 10 English PHYSICAL SETUP 2. Plug the free end of the monitor cable into the connector labeled A/V OUT to Monitor on the control console. 3. Plug the power supply output cord into the control console Power connector. Control console AC power cord Power Power supply output cord A/V OUT to Monitor Monitor cable Power supply 4.
00.Marley_Setup.book Page 17 Tuesday, January 10, 2012 8:47 AM English Tab 2, 10 Tab 3, 11 Tab4, 12 Tab 6, 14 Tab 5, 13 Tab 7, 15 Tab 8,16 INTERACTIVE SETUP Starting the system You are now ready to turn on your system and complete the setup process using the Unify intelligent integration system. ® Here is what you need from Box 2: Box 2 additional included items: These are items you may need to connect A/V devices to your system.
00.Marley_Setup.book Page 18 Tuesday, January 10, 2012 8:47 AM Tab 8, 16 Tab 7, 15 Tab 6, 14 Tab 5, 13 Tab 4, 12 Tab 3, 11 Tab 2, 10 English INTERACTIVE SETUP 1. Press the power button ( ) on the control console. The power light on the control console indicates the startup status. Note: When the system starts up, you will hear a start-up tone, and on the monitor screen you will see the Bose logo with a progress bar under it. ® 2.
05.Marley_Setup_Interactive.fm Page 19 Tuesday, January 10, 2012 8:53 AM English Tab 2, 10 Tab 3, 11 Tab4, 12 Tab 6, 14 Tab 5, 13 Tab 7, 15 Tab 8,16 INTERACTIVE SETUP 5. When the system is started up for the first time the following instruction appears on the monitor in many languages: “Press and hold the OK button on the Bose remote until the screen turns black.” If you have setup problems If you experience setup problems, the Unify intelligent integration system can help you identify the issue.
VideoWave2 Setup Guide Covers_AIM.fm Page 1 Tuesday, January 10, 2012 9:48 AM Setup Guide Guía de instalación Guide d’installation ©2012 Bose Corporation, The Mountain, Framingham, MA 01701-9168 USA AM352276 Rev.
