CCTV TM Instructions ule “Send 2 Video Signals Down 1x Co-ax Cable...” ...with a TM CCTV ule Even audio! Video In 2 Video In 1 1x RG5 9 OUT CCTV MULE • • • 12V DC • Up to 2 videos down co-ax* • No need for extra cables* • 2 2 Video signals down 1 co-ax.
CCTV Mule Instructions CCTV TM ule Carries multiple video signals even audio down ONE RG59 cable! The CCTV Mule makes it easy to add extra cameras to existing installations, you save installation time and reduce the cost of buying and installing more cable. The Mules work in pairs. One Mule combines the video signals to transmit them down 1 single co-ax, the other Mule then reconstructs the individual video signals at the remote end.
CCTV Mule Instructions Mode 1 Video signal in one direction, 1 video signal in the opposite direction. 2 Mule 2 - Tx Mule 2 - Rx V1 12V DC V1 in this direction V2 V2 12V DC V1 1x RG59 co-ax cable V2 in this direction Mode 1 Video signal and 1 audio signal. 3 Mule 2 - Tx Mule 2 - Rx V1 12V DC Audio 12V DC Audio V1 & Audio in this direction V1 1x RG59 co-ax cable Mode 1 Video signal in one direction, 1 audio signal in the opposite direction.
CCTV Mule Instructions Step 2 - identify the relevant connections on the Mule2. Connections - TX Transmitter Each CCTV Mule is clearly marked on the power side as: Tx - Transmitter Tx - Transmitter Figure 1 Tx - Transmitter unit has the following connections; 1. Power Input 12v D.C Only 2. Power L.E.D 3. Video Input Brightness Adjust Connections - RX Receiver 4. Channel 1 Video Input 5. Video Output to Mule Receiver 6.
CCTV Mule Instructions Step 3 - fasten the unit to a wall Installation The units have wall mount fixings lugs either side for internal installation however for external installation the Mules MUST be installed in a suitable IP rated enclosure such as the BOX420 (figure 3). Figure 3 Step 4 - power the units. Powering the Units The Mules require a 12v power supply to power the units, so you will require 2 power supplies. One for the transmitter and one for the receiver.
CCTV Mule Instructions Step 5 - set up your chosen mode. Operation Mode Setup Mode 2 Video signals down 1 co-ax cable 1 The Mule2 allows 2 separate video signals to be sent down 1 co-ax cable allowing 1 extra CCTV camera to be added to an existing system. Figure 6 shows a diagram of how mode 1 is configured. Figure 6 Mule 2 - Tx Mule 2 - Rx V1 12V DC V2 V2 12V DC V1 & V2 in this direction V1 1x RG59 co-ax cable Tx - Transmitter 1.
CCTV Mule Instructions Operation Mode Setup Mode 1 Video signal in one direction, 1 video signal in the opposite direction. 2 Mule2 can also transmit a CCTV video signal in reverse. This great feature is an added bonus where wirefree is not an option due to site conditions such as trees and other obstacles in the way, especially useful if you don’t have access to run any more cables. Figure 7 shows a diagram of how mode 2 is configured.
CCTV Mule Instructions Operation Mode Setup Mode 1 Video signal and 1 audio signal. 3 The Mule2 can also send an extra audio signal down the RG59 allowing 1 camera signal and 1 audio to be sent back to a monitor. There’s no need to add extra cable to the existing RG59 co-ax cable as all this can be done with the Mule2. Figure 8 shows a diagram of how mode 3 is configured.
CCTV Mule Instructions Operation Mode Setup Mode 1 Video signal in one direction, 1 audio signal in the opposite direction. 4 The Mule2 is capable of transmitting audio in the reverse direction to 1 video camera signal. This mode works especially well in an existing installation where 1 of the cameras could be converted into a tannoy system using the VoiceOff. No additional cabling would be required to complete this setup.
CCTV Mule Instructions Troubleshooting Q.1 I have power to both Mules but I can not get any video out of them. I have all the cameras connected and outputs connected to the DVR. A.1 Check the Mules are connected the correct way around. The transmitter Mule (TX) should have the camera inputs connected to it and sited at the camera end. The receiver Mule (RX) should have the video outputs connected to the DVR and should be sited at the DVR end.
Also available in 4 way - the Mule4 CCTV Mule Range Send 4 Video signals down 1 Co-ax cable ...with a CCTV TM ule Even aud & data! io 4 eo MULE 1x In CCTV Vi x 4 d 5 RG 9 UT O 5 Operation Modes! Mode 3 Video signals in one direction, 1 RS485 signal in the opposite direction.
F or mo www. re info go to Voice Off.co : m Other items to consider...
TM VideoMitters Digital Transceivers Monitor & control video & sound from one location to another without wires! Up to 1.2Km Range* The VideoMitters are a break through in the transmission of video signals. By digitising the video & audio signals, far superior performance can be achieved in transmission distance and received image & audio quality.
Keep vital evidence secure from tampering or theft by fitting your DVR into a KitVault lockable enclosure... For more info go to: www.kitvault.
Introducing the Who is Watching Me Signage Solutions No Overprinting Required! FAST, EASY, LOW COST, SMART & CONVENIENT Each sign is pre−printed with a unique serial number, so overprinting is a thing of the past. Pre−drilled holes speed up installation and rounded corners help comply with H&S regulations. You register your unique “Sign ID” to your contact details at an online data base so the public are able to contact you as is required by the Data Protection Act.
TM CCTV ule Specifications Send 2 Video signals down 1 co-ax cable with a Mule2 Even audio! Video In 2 1x RG5 Video In 1 9 OUT For further information or help please contact us by email: support@cctvmule.com or visit us online at: www.cctvmule.
