User manual

Display setup
System information
The speed dome setup menu allows the operator to customise and
program all aspects of speed dome operation. All menu settings are
retained in non-volatile memory so if power is lost to the speed dome
for any reason, all settings will be retained.
CONCEPT PRO SPEED DOME
-----------------------------
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<MOTION SETUP>
<FUNCTION SETUP>
<CAMERA SETUP>
<SYSTEM SETUP>
<SYSTEM INITIALISE>
EXIT
DISPLAY SETUP
-----------------------------
CAMERA ID
PTZ INFORMATION
ACTION TITLE
PRESET LABEL
ALARM I/O
DATE/TIME
TEMPERATURE
<PRIVACY ZONE>
BACK
EXIT
SYSTEM INFORMATION
-----------------------------
FIRMWARE VER
COLOUR SYSTEM
PROTOCOL
BAUD RATE
ADDRESS
BACK
EXIT
To access the speed dome setup menu, key:
PRESET - 95 - ENTER
If the password has been enabled, it must be
entered before the menu can be accessed.
See page 12 for password setup information.
To navigate the main menu, move the joystick
up / down to choose a menu item or change
settings within a menu item.
To enter a menu item or confirm a new setting,
key: NEAR
To exit a menu item or cancel a new setting,
key: FAR
Where a menu item is surrounded by
brackets, it indicates that there is a sub menu.
Where a menu screen shows EXIT, selecting
this option will exit the menu and the speed
dome will return to normal operation. Where a
menu screen shows BACK, selecting this
option will return to the higher menu level.
The main menu has seven options:
<SYSTEM INFORMATION> - Provides
information such as firmware version, protocol
and ID values as defined by the dip switch
settings.
<DISPLAY SETUP> - Allows the operator to
specify which On Screen Display information
is shown during normal operation. Also allows
privacy zones to be defined.
<MOTION SETUP> - setup of the pan / tilt /
zoom operation of the speed dome, park
action configuration, and configuration of the
alarm inputs.
<FUNCTION SETUP> - Allows configuration
of presets, VST functions, patterns, groups
and scheduled events.
<CAMERA SETUP> - Allows configuration of
the operating parameters of the 10x zoom
module.
<SYSTEM SETUP> - Allows configuration of
time/date, fan/heater operating temperatures,
password setting, Home position configuration
and North direction configuration.
<SYSTEM INITIALISE> - Any or all of the
speed dome settings can be restored to
factory defaults. The speed dome can also be
re-booted with this menu option.
From the main menu, use the joystick to
highlight SYSTEM INFORMATION and key:
NEAR
To return to the main menu, highlight BACK
and key: NEAR
To exit the setup menu completely, highlight
EXIT and key: NEAR
PTZ INFORMATION (ON / OFF / AUTO) -
shows the current pan / tilt position in degrees
and the current zoom level.
ACTION TITLE (ON / OFF / AUTO) - shows
current speed dome action, eg PRESET3.
PRESET LABEL (ON / OFF / AUTO) - shows
preset label (if defined) when a preset is
called.
ALARM I/O (ON/OFF) - shows real time status
of the alarm inputs and outputs.
DATE/TIME - shows current date and time.
TEMPERATURE (CELSIUS / FAHRENHEIT /
OFF) - shows current operating temperature of
the speed dome.
<PRIVACY ZONE> - sub menu to setup the
speed dome privacy zones.
Highlight the item to modify and key: NEAR
Use the joystick to change the setting and key:
NEAR to save or: FAR to cancel.
Note: If the auto option is chosen, the
relevant information is displayed for a few
seconds before disappearing.
From the main menu, use the joystick to
highlight DISPLAY SETUP and key: NEAR
CAMERA ID (ON / OFF) - shows camera ID
according to the DIP switch settings, eg
CAM 1.
: 2.030V
: PAL
: PELCO-D
: 2400
: 1
ON
AUTO
AUTO
AUTO
AUTO
ON
CELSIUS
Programming the speed dome
6