Use and Care Manual
ENGLISH
INSTRUCTIONS POUR L'INSTALLATION
WALL LUMINAIRE
Product name
QUAD U
Read this short manual carefully and keep it accessible for further
reference!GENERAL SAFETY MESSAGES
Life-threatening danger due to
electric shock, danger of fire and danger from
falling objects may exist if the following is not
respected!
This luminaire must be installed in accordance
with the National Electric Code, Canadian
Electrical Code, State, provincial, and local
regulations by a licensed electrician.
Disregard of the safety messages may lead to danger of life, burning or
fire!
Installation, mounting or works on the electrical connection may only be
carried out by a licensed electrician.
The product may not be modified or converted.
Do not hang or fasten anything on the product, especially no decoration.
Do not cover the product - provide free air circulation.
The luminaire may only be operated with a complete and intact protection
glass.
In case of a malfunction you may NOT touch the product or operate it
further. Disconnect the product from the power supply by an external
switch or by the fuse.
A malfunction exists when:
visible damages appear.
the product does not work properly (e.g. flickering).
smoke, steam or crackling sounds appear.
smell of burning is recognisable.
an overheating is recognisable (e.g. by discolouration of adjacent
surfaces).
Operate the product only after maintenance and examination by an
approved electrician!
This product is not intended to be used by children. Ensure that children do
not suffer any harm e.g. by burns from hot surfaces or by electrical shock.
Additional safety messages are indicated by this symbol: .
USE AS DIRECTED
This product serves exclusively lighting purposes and may:
only be used with a voltage of 120V ~60Hz.
only be operated whwn firmly mounted on a stable, even and tilt-fixed
surface.
only be operated on normally or not flammable surfaces.
not be exposed to strong mechanical loads or to strong contamination.
OPERATION
The distance between the light source and the illuminated surface must be
at least 2.62 ft. . Pay special caution to easily inflammable objects (e.g.
curtains, fabrics, foliage, etc.).
MAINTANANCE AND CARE
Care
The following enviromental influences may have unwanted effects on the
surface of the product:
acid rain and sour soil, high salt content in the air
cleaning agents, fertilizer especially in flowerbeds
thawing salt, other chemical substances (e.g. herbicides)
Protect the product by adequate means to avoid unwanted changes of the
surface.
Disconnect the product from the power supply and let it cool down, before
you clean the product.
Clean the product on a regular basis using a slightly moistened, soft and fluff-
free cloth. Please also note additional supplied notes on maintanance and
care.
STORAGE AND DISPOSAL
Storage
The product must be stored in a dry and clean environment. Do not strain
the product mechanically during storage.
After a damp or soiling storage the product may only be installed after
checking its condition by an approved electrician.
INSTALLATION (only by a licensed electrician)
Switch off the mains breaker and switch before doing any work!
Use only parts, which are supplied with the product or are described as
accessories!
Inspect the product for loose parts inside the housing. When there are loose
parts inside the housing and these are not explicitly described the product may
not be installed or operated.
Use the supplied fastening material only when it is suited for the installation
background. If this is not the case use only fastening material suiting the
installation background.
Unpacking
Carefully take the product out of the packaging removing any transport
safeguards.
Before disposal of the packaging material make sure that all components
of the product are removed.
Installation place
Products are solely suited for installation on a wall.
Note the security advice on the distance to the illuminated surface in the
chapter OPERATION.
The product may only be utilized according to IP44.
IP44: Protection against foreign objects > Ø .1cm - Protection against
splashing water from all directions.
Prepare the power supply lead according to valid rules for outdoor
installations.
Do not seal the product yourself, using additional silicon or another
sealant.
Installation steps (read completely before installation)
Install the luminaire as shown in the figure.
Electrical Connection
The product must be able to be separated by a 120V pole separation
(breaker and switch) from the current supply.
Install the mounting plate to the electrical junction box.
Direct the connection lead through the rubber gasket into the
luminaire.
Equip the three wire ends with protective tubes.
For electric connection attach the black wire (live conductor marked
L) of the fixture and the white wire (neutral conductor marked N) of
the fixture with the corresponding 120V wires in the junction box. The
green-yellow wire (protective conductor) of the connection lead has
to be tightly fastened to the earth clamp of the product.
Secure the fixture to the mounting plate with two screws.
Check if the product functions properly and is securely fixed!
art.-no.751641U_44U_48U 03/2016
© SLV Lighting North America,
5022 Joanne Kearney Blvd.,
Tampa, FL 33619 USA
Tel. (813) 349-1900
Technical Details are subject to change.