Instruction Manual

2. The second fuse position of Distributor-2 holds a 150A fuse for the positive outputs of both
Smart Solar charge controllers MPPT 100|50. The lower negative is used for the Quattro
second negative connection as both negative outputs for the Solar charge controllers are
connected to the negative Busbar. !
3. The third fuse position of Distributor-2 holds a 250A fuse for Smart Battery Protect-1 220.
Its lower positioned negative connection is used to connect to the Negative Busbar. Keep the
distance between Lynx Distributor fuse-3, Main switch-2 and SBP-1 as short as possible.!
4. The fourth fuse postion of Distributor-2 holds a 250A fuse for Smart Battery Protect-2 220.
Its lower positioned negative connection is used to connect to the Negative Busbar. Keep the
distance between Lynx Distributor fuse-4, Main switch-2 and SBP-2 as short as possible. !
Main switch-1 is a single circuit model used for the Quattro with dual output connections to
provide two positive connections towards the Quattro.!
Main switch-2 is a dual circuit model used for Main fuse 3 and 4 towards SBP-1 and SBP-2. !
The PE/Earth connection will be dealt with later together with the Quattro.!
Lynx Distributor-3 (Dip switch Pos-C)
1. The first fuse position of Distributor-3 at the bottom of the Distributor holds a 150A fuse
together with its lower positioned negative connection for the extra STBD Alternator. Also look
at the 3 Amp in line fuse for the WS500 battery sense STBD connected to the same 150A fuse
and the negative connection for the WS500 battery sense STBD connected to the negative
busbar of Distributor-3.!
2. The second fuse position of Distributor-3 holds a 150A fuse together with its lower positioned
negative connection for the extra PORT Alternator. Also look at the 3 Amp in line fuse for the
WS500 battery sense PORT connected to the same 150A fuse and the negative connection
for the WS500 battery sense PORT connected to the negative busbar of Distributor-3.!
Main fuse 3 and 4 are Spares and can be used for future users or charge possibilities.!
Smart Battery Protect 1/220:
This smart battery protect 220 is used for DC loads 1 till 5. One can make a choice what to use it
for. The SBP is needed to protect the Li batteries from discharging beyond a low Voltage setpoint.
It comes highly recommended to install a fuse of 300mA in the negative connection of the SBP. !
Smart Battery Protect 2/220:
This smart battery protect 220 is used for DC loads 6 till 10. One can make a choice what to use it
for. The SBP is needed to protect the Li batteries from discharging beyond a low Voltage setpoint.
It comes highly recommended to install a fuse of 300mA in the negative connection of the SBP. !
Cerbo GX with GX Touch 50 Display:
The Cerbo GX with its GX Touch 50 Display is visible next to Distributor-3. This device together
with the GX Touch 50 Display is the monitoring heart of your installation showing you what is
going on with all connected devices. Monitoring of your installation can be done either with the
Cerbo in front of you or from anywhere in the world using an internet connection as shown in the
drawing with VRM World that connects to the Victron VRM portal either using the Victron connect
app or website. The Cerbo also provides Remote Firmware updates and allows settings to be
changed Remotely. This all has been clearly explained in the Cerbo manual.!
The positive power for the Cerbo comes from the Lynx Smart BMS AUX connections as explained
with the BMS. The GX Touch 50 Display HDMI connector with attached USB power cable
obviously has to go into the HDMI port of the Cerbo and the USB cable directly next to it.!
The VE.Bus cable coming from the Quattro go’s into a VE.Bus port of the Cerbo and the Ethernet
cable and its connector, to connect to the VRM Portal, into the Network port of the Cerbo. The
VE.Direct cables from Smart Solar MPPT 100|50 Port and Stbd, both connect into a VE.Direct port
of the Cerbo. Data at VE.Can bus level to/from the Lynx Smart BMS has to be connected to the
Cerbo VE.Can port. Do not forget to terminate the Can bus at the Cerbo with a Victron terminator.!
These are all the connection you have to make for the Cerbo. There is plenty more you can
connect and do with a Cerbo and that all is very well explained in its manual.!
Smart Solar charge Controller MPPT 100|50 Port:
Page-3