SED-WIN / SED-DOR Wireless Door and Window Switch Installation Guide CONTENTS Installation Self Testing Location Operation Overview Model Chart Pairing Process Procedure Configuring Actions Using VT8000 Controllers for Stand-alone Systems Using VT8000 Controllers for Networked Systems Important Notes Before Starting Pairing Procedure Pairing – Associating Switches with Controllers Multiple Switch Configuration Troubleshooting Guide Status and Monitoring Battery Status Specifications Drawing and Dimensions
Wireless Door/Window Switch SED-WIN/SED-DOR INSTALLATION SED-WIN & SED-DOR Installation 1. Remove cover by pulling on side where security screw was mounted (Figure-1). 2. Remove cover of magnet unit. 3. Read FCC ID and IC label inside removed cover. 4. Cut out mounting template (end of this manual) for install. Do not place it on hinge side of door unless self tested. 5. Locate template and mark four holes for self-tapping screws. 6.
Wireless Door/Window Switch 3 SED-WIN/SED-DOR The SED-WIN & SED-DOR series ZigBee Pro™ wireless switches are used with the wireless versions of VT8000/VT7000 Series Terminal Equipment Controllers. A typical hospitality application is where the VT8000 wall terminal equipment controller has an on-board PIR sensor and wireless switches are used to monitor the opening and closing of doors and windows.
Wireless Door/Window Switch SED-WIN/SED-DOR Pairing Process Procedure NOTE: See VTR/VT installation manual for details on PAN ID parameter.
Wireless Door/Window Switch SED-WIN/SED-DOR 5 Figure-8 Typical Stand-alone floorplan © 2014 Viconics Technologies Inc. All rights reserved. Typical floor plan of a unique network for Stand-Alone systems with VT8000 Controllers: Viconics Technologies Inc. | 9245 Langelier Blvd. | St.-Leonard | Quebec | Canada | H1P 3K9 | Tel: (514) 321-5660 | Fax: (514) 321-4150 028-0415-01 www.viconics.com | sales@viconics.
Wireless Door/Window Switch SED-WIN/SED-DOR PAN ID used with a Range of 1 to 500 for Networked Systems In this application, any controller(s) are routers to the system. The MPM is the coordinator to the system as the MPM is the network master for any controller(s) reporting to them. • Wireless controller factory default Channel and PAN ID = controller(s) offline. • MPM is network coordinator. • VT8000/7000 controllers act as a router. • Range of PAN ID on all controllers use 1 - 500.
Wireless Door/Window Switch SED-WIN/SED-DOR 7 Important: Device Pairing Order If a VT8000 controller that already has a SED-WIN & SED-DOR wireless switch paired with it is then paired with an MPM, the paired wireless switch will fail to function normally. To avoid this problem, always pair all VT8000 controllers to be used in a networked environment with the appropriate MPMs before you pair them with SED-WIN & SED-DOR wireless switches.
Wireless Door/Window Switch SED-WIN/SED-DOR Pairing - Associating Switches with Controllers 1. 2. 3. 4. 5. 6. 7. 8. 9. Remove the pull tab from the battery holder to power-up the switch. Verify or set configuration parameter “BI1” or “BI2” to “None”. This sequence will erase the current associated devices. Set the configuration parameter “BI1” to “Window” and “BI2” to “DoorDry” as required.
Wireless Door/Window Switch 9 SED-WIN/SED-DOR Troubleshooting Guide NOTE: If the wireless switch has not yet been paired, restart the pairing procedure.
Wireless Door/Window Switch SED-WIN/SED-DOR Battery Status To verify the battery strength of the wireless switch, simply short the switch for more than 4 seconds and less than 10 seconds and a blinking pattern will be displayed. After the blinking pattern is displayed, the switch will enter diagnostic mode for a duration of 10 seconds (see Status and Monitoring).
Wireless Door/Window Switch SED-WIN/SED-DOR 11 Drawing and Dimensions Figure-12 Magnet and Magnet Base Dimensions © 2014 Viconics Technologies Inc. All rights reserved. Figure-11 Switch and Switch Base Dimensions Viconics Technologies Inc. | 9245 Langelier Blvd. | St.-Leonard | Quebec | Canada | H1P 3K9 | Tel: (514) 321-5660 | Fax: (514) 321-4150 028-0415-01 www.viconics.com | sales@viconics.
Wireless Door/Window Switch SED-WIN/SED-DOR Location of Security Screws © 2014 Viconics Technologies Inc. All rights reserved. Marking Templates for Mounting Viconics Technologies Inc. | 9245 Langelier Blvd. | St.-Leonard | Quebec | Canada | H1P 3K9 | Tel: (514) 321-5660 | Fax: (514) 321-4150 028-0415-01 www.viconics.com | sales@viconics.