Wireless Door/Window Switch 1 SED - WIN/SED - DOR Wireless Door and Window Switch Installation Guide CONTENTS Installation Self Testing Location Operation Overview Model Chart Pairing Process Procedure Configuring Actions Using SERx300 Controllers for Stand-alone Systems Using SERx300 Controllers for Networked Systems Important Notes Before Starting Pairing Procedure Pairing – Associating Switches with Controllers Multiple Switch Configuration Troubleshooting Guide Status and Monitoring Battery Status S
Wireless Door/Window Switch SED - WIN and SED - DOR 2 INSTALLATION SED - WIN/SED - DOR Installation 1. Remove cover by pulling on side where security screw was mounted (Figure-1). 2. Remove cover of magnet unit. 3. Read FCC ID and IC label inside removed cover. 4. Cut out mounting template (end of this manual) for install. Do not place it on hinge side of door unless self tested. 5. Locate template and mark four holes for self-tapping screws. 6.
Wireless Door/Window Switch SED - WIN and SED - DOR 3 Operation Overview SED-WIN and SED-DOR series Zigbee Pro™ wireless switches are used with wireless versions of SERx3XX Series Fan Coil Terminal Equipment Controllers. A typical hospitality application SERx3xx wall terminal equipment controller has an on-board PIR sensor. Wireless switches monitor opening and closing of doors and windows.
Wireless Door/Window Switch SED - WIN and SED - DOR 4 Pairing Process Procedure NOTE: See SER/SE installation manual for details on PAN ID parameter. PAN ID for Centralized Networked Applications with MPM SER8300 Series 1 - 500 SE 72 / 73 Series* 1 - 250 PAN ID for Stand-alone Applications with no MPM SER8300 Series SE 72 / 73 Series* 501 - 1000 251 - 500 Note: SE7000 Room Controllers are only compatible if a network with a Coordinator is present.
Wireless Door/Window Switch SED - WIN and SED - DOR 5 Floor Plan Stand-Alone Systems with SER8300 Controllers All brand names, trademarks and registered trademarks are the property of their respective owners. Information contained within this document is subject to change without notice. Schneider Electric One High Street, North Andover, MA 01845 USA Telephone: +1 978 975 9600 Fax: +1 978 975 9674 http://www.schneider-electric.com/buildings II-SE8000-SEDWINDOR-US.EN.10.2013.
Wireless Door/Window Switch SED - WIN and SED - DOR 6 PAN ID used with a Range of 1 to 500 for Networked Systems In this application, any controller(s) are routers to the system. The MPM is the coordinator to the system as the MPM is the network master for any controller(s) reporting to them. • Wireless controller factory default Channel and PAN ID = controller(s) offline. • MPM is network coordinator. • SER8300/SE7000 controllers act as a router. • Range of PAN ID on all controllers use 1 - 500.
Wireless Door/Window Switch SED - WIN and SED - DOR 7 Before Starting Pairing Procedure Verify the following parameters on the SER8300 controller are set correctly to avoid failure. PAN ID Personal Area Network Identification Default value = 0 Range: 0 -1000 This parameter only appears when a wireless network adapter is present. If the Terminal Equipment Controller is installed as a standalone unit or with a BACnet™ or Echelon™ adapter, this parameter is not used or displayed.
Wireless Door/Window Switch SED - WIN and SED - DOR 8 Pairing Associating Switches with Controllers 1. 2. Remove pull tab from battery holder to power-up switch. Verify or set configuration parameter BI1 or BI2 to None to erase current associated devices. 3. Set configuration parameter BI1 to Window and BI2 to DoorDry. 4. To reset wireless switch to its factory default settings if previously associated, short switch and hold for 20+ seconds. 5 short blinks will confirm reset (see Figure-5). 5.
Wireless Door/Window Switch SED - WIN and SED - DOR 9 Troubleshooting Guide NOTE: Restart pairing procedure if wireless switch is not yet paired.
Wireless Door/Window Switch SED - WIN and SED - DOR 10 Battery Status To verify battery strength of the wireless switch, jump switch for 4+ seconds and less than 10 seconds and ensure a blinking pattern shows. After the blinking pattern shows, the switch enters diagnostic mode for 10 seconds.
Wireless Door/Window Switch SED - WIN and SED - DOR 11 Drawing and Dimensions The illustration below shows dimensions for the switch and switch base. All brand names, trademarks and registered trademarks are the property of their respective owners. Information contained within this document is subject to change without notice. Schneider Electric One High Street, North Andover, MA 01845 USA Telephone: +1 978 975 9600 Fax: +1 978 975 9674 http://www.schneider-electric.com/buildings II-SE8000-SEDWINDOR-US.
Wireless Door/Window Switch SED - WIN and SED - DOR 12 Marking Templates for Mounting All brand names, trademarks and registered trademarks are the property of their respective owners. Information contained within this document is subject to change without notice. Schneider Electric One High Street, North Andover, MA 01845 USA Telephone: +1 978 975 9600 Fax: +1 978 975 9674 http://www.schneider-electric.com/buildings II-SE8000-SEDWINDOR-US.EN.10.2013.v1 October 2013 © 2013 Schneider Electric.
