Installation and Operation Guide XX-223-00-00 VM-608LCD Flat Panel LCD Monitor Vicon Industries Inc., 89 Arkay Drive, Hauppauge, New York 11788 Tel: 631-952-CCTV (2288) Fax: 631-951-CCT (2288) Toll Free: 800-645-9116 24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: 44/(0) 1489-566300 Vicon Industries Inc.
SAFETY INSTRUCTION CAUTIONS ………………………………………………………………….. 2~3 ……………………………………………………………….......................... 4~5 FCC RF INTERFERENCE STATEMENT ……………………………........................... CONNECTING WITH EXTERNAL EQUIPMENT 6 ………………………………………. 7 ………………………………………………………….. 8 ~ 25 MOUNTING GUIDE ……………………………………………………………………….. 26 ~ 27 CONTROLS AND FUNCTIONS D-SUB CONNECTOR PIN ASSIGNMENTS ……………………………………………. 28 …………………………………………………………………. 29 ………………………………………………………………………….
Important Safeguards – Indoor Use GRAPHIC SYMBOL EXPLANATION 12. Lightning - Disconnect the product from its power source and The lightening bolt symbol alerts the user to the presence of cable system when possible to prevent damage due to lightning dangerous voltage that may present the risk of electric shock. and power-line surges. 13. Power Lines - Do not locate outside cables over power or utility lines where they can fall and make direct contact. Contact with power lines can be fatal. 14.
Important Safeguards – Indoor Use (Cont) 22. For Rack-Mounted Units Only – The following precautions apply to all rack-mounted units. a) Elevated Operating Ambient - If installed in a closed or multiunit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.
CAUTION The power supply cord is used as the main disconnect device, ensure that the socket-outlet is located/installed near the equipment and is easily accessible. ATTENTIONN Le cordon d`alimentation est utillsé comme interrupteur général. La prise de courant doit être située ou installée à proximité du matériel et être facile d`accès ▶ NEVER REMOVE THE BACK COVER Removal of the back cover should be carried out only by qualified personnel.
"Rack Mount Instructions - The following or similar rack-mount instructions are included with the installation instructions: A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.
FCC Notice Note: Complies with Federal Communications Commission Rules & Regulations Part 15, Subpart B for a Class A digital device. WARNING This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instruction, may cause interference to radio and television reception.
A. BACK 1. TRIGGER INPUT Sensor Signal Input 2. AUDIO IN 3.5Φ STEREO IN 3. S-VIDEO IN Y/C separated signal input 4. AV1 IN Composite signal Input for AV1 5. AV1 OUT Video looping output for AV1 6. AV2 IN Composite signal Input for AV2 7. AV2 OUT Video looping output for AV2 8. VGA PC Analog Signal Input 9. DC12V 1 2 3 4 5 6 7 8 9 INSTRUCTION MANUAL …………………………………………………………………….
B. FRONT 1. INPUT Select input source. 2. MENU Activates and exits the On Screen Display. This button can also be used to move previous menu or status. OSD MENU(MAIN) : Input Source, Screen, Audio, OSD, Color, Utility, Exit. 3/4. ▲ / ▼ This button allows user to enter the sub-menu of the activated function ▼ : Auto geometry adjustment in PC Source. 5/6. ◀ / ▶ Adjust the volume / Adjust menu settings. 7. POWER ON/OFF Turns the power ON or OFF. There will be a few seconds delay before the display appears. 8.
OSD Menu Description A: CUSTOM MENU (For AV1, AV2 & S-Video Input) 1) Press the MENU button and then press the up(▲) or down(▼) button to select the Custom. 2) Press the up(▲) or down(▼) button to select the sub menu. 3) Press the left(◀) or right(▶) button to adjust the picture setting. 4) Press the MENU button to save. Brightness: Increase or decrease the intensity of the image. Contrast: Increase or decrease the intensity (lightness or dimness) of the image.
B. Picture / Sound Menu (For AV1, AV2 & S-Video) 1. Picture Mode 1) Press the MENU button and then press the up(▲) or down(▼) button to select the Picture / Sound. 2) Press the right(▶) or INPUT button. 3) Press the up(▲) or down(▼) button to select the Picture Mode. 4) Press the right(▶) or INPUT button. 5) Press the up(▲) or down(▼) button to select the Picture Mode option. 6) Press the MENU button to save 2. Color Tone 1) Press the up(▲) or down(▼) button to select the Color Tone.
3. Mute 1) Press the up(▲) or down(▼) button to select the Mute. 2) Press the right(▶) or INPUT button. 3) Press the up(▲) or down(▼) button to select the On or Off. 4) Press the MENU button to save. 4. Volume 1) Press the up(▲) or down(▼) button to select the Volume 2) Press the left(◀) or right(▶) button to adjust Volume setting. 3) Press the MENU button to save. INSTRUCTION MANUAL …………………………………………………………………….
5. Size 1) Press the up(▲) or down(▼) button to select the Size 2) Press the right(▶) or INPUT button. 3) Press the up(▲) or down(▼) button to select the Size option. 4) Press the MENU button to save. 6. NR 1) Press the up(▲) or down(▼) button to select the NR. 2) Press the right(▶) or INPUT button. 3) Press the up(▲) or down(▼) button to select the On or Off. 4) Press the MENU button to save. 12 …………………………………………………………………….
7. 3D Comb 1) Press the up(▲) or down(▼) button to select the 3D Comb. 2) Press the right(▶) or INPUT button. 3) Press the up(▲) or down(▼) button to select the On or Off. 4) Press the MENU button to save. 8. Camera 540 3) Press the up(▲) or down(▼) button to select the Camera 540 menu. 4) Press the right(▶) or INPUT button. 5) Press the up(▲) or down(▼) button to select the Camera 540 option. 6) Press the MENU button to save. INSTRUCTION MANUAL …………………………………………………………………….
B. Picture / Sound Menu (For PC Input) 1. Picture Mode 1) Press the MENU button and then press the up(▲) or down(▼) button to select the Picture/Sound. 2) Press the right(▶) or INPUT button. 3) Press the up(▲) or down(▼) button to select the Picture Mode. 4) Press the right(▶) or INPUT button. 5) Press the up(▲) or down(▼) button to select the Picture Mode option. 6) Press the MENU button to save. 2-1. Color Tone 1) Press the up(▲) or down(▼) button to select the Color Tone.
3) Press the left(▶) or INPUT button again. 4) Press the up(▲) or down(▼) button to select the Color Tone option. 5) Press the MENU button to save. 2-2. Color Tone (Custom) 1) Press the up(▲) or down(▼) button to select the Custom in the Color Tone. 2) Press the Menu button to save. INSTRUCTION MANUAL …………………………………………………………………….
3) Press the up(▲) or down(▼) button to select the Red(R), Green(G) or Blue(B). 4) Press the left(◀) or right(▶) button to adjust color density. 5) Press the MENU button to save. 4. PC control (Only PC Input) 1) Press the up(▲) or down(▼) button to select the PC. 2) Press the right(▶) or INPUT button. 3) Press the up(▲) or down(▼) button to select the PC sub menu. 4) Press the right(▶) or INPUT button. 5) Press the left(◀) or right(▶) button to adjust the PC setting. 6) Press the MENU button to save.
C. SETUP MENU 1) Press the MENU button and then press the up(▲) or down(▼) button to select the Setup. 1. Reset 1) Press the right(▶) or INPUT button 2) Press the right(▶) or INPUT button again. 3) Press INPUT button to execute the reset. Reset: All settings go to the factory initialization. INSTRUCTION MANUAL …………………………………………………………………….
2. Language 1) Press the up(▲) or down(▼) button to select the Language. 2) Press the right(▶) or INPUT button. 3) Press the up(▲) or down(▼) button to select language. 4) Press the MENU button to save. 3. OSD Tone 1) Press the up(▲) or down(▼) button to select the OSD Tone. 2) Press the right(▶) or INPUT button 3) Press the up(▲) or down(▼) button to select the OSD Tone option. 4) Press the MENU button to save. 18 …………………………………………………………………….
4. Blue Screen 1) Press the up(▲) or down(▼) button to select the Blue Screen. 2) Press the right(▶) or INPUT button. 3) Press the up(▲) or down(▼) button to select the On or Off. 4) Press the MENU button to save. 5. Key Lock 1) Press the up(▲) or down(▼) button to select the Key Lock. 2) Press the right(▶) or INPUT button 3) Press the up(▲) or down(▼) button to select the On or Off 4) Press the MENU button to save. ※ How to unlock: Press the INPUT and MENU button at the same time over 3 seconds.
6. Trigger 1) Press the up(▲) or down(▼) button to select the Trigger. 2) Press the right(▶) or INPUT button. 6-1. Trigger Enable 1) Press the up(▲) or down(▼) button to select the Trigger Enable. 2) Press the right(▶) or INPUT button. 3) Press the up(▲) or down(▼) button to select the On or Off. 4) Press the Menu button to save. 20 …………………………………………………………………….
6-2. Trigger Input 1) Press the up(▲) or down(▼) button to select the Trigger Input . 2) Press the right(▶) or INPUT button. 3) Press the up(▲) or down(▼) button to select the Trigger Input option. 4) Press the Menu button to save. 6-3. Buzzer 1) Press the up(▲) or down(▼) button to select the Buzzer. 2) Press the right(▶) or INPUT button. 3) Press the up(▲) or down(▼) button to select the On or Off. 4) Press the Menu button to save. INSTRUCTION MANUAL …………………………………………………………………….
6-4. Trigger Time 1) Press the up(▲) or down(▼) button to select the Trigger Time. 2) Press left(◀) or right(▶) button to adjust Trigger Time setting. 3) Press the MENU button to save. 6-5 Trigger Option 1) Press the up(▲) or down(▼) button to select the Trigger Option. 2) Press the right(▶) or INPUT button. 3) Press the up(▲) or down(▼) button to select the Trigger Option setting. 4) Press the Menu button to save. ※ N/C (Normal Closed): When Trigger cable is opened, Trigger function is activated.
7. Auto switching 1) Press the up(▲) or down(▼) button to select the Auto switching. 2) Press the right(▶) or INPUT button. 7-1. Auto switching On/Off 1) Press the right(▶) or INPUT button. 3) Press the up(▲) or down(▼) button to select the On or Off . 4) Press the Menu button to save. INSTRUCTION MANUAL …………………………………………………………………….
7-2. Auto switching Inputs enabled 1) Press the up(▲)or down(▼) button to select the Inputs enabled. 2) Press the right(▶) or INPUT button. 3) Press the up(▲) or down(▼) button to select the Input. 4) Press the right(▶) or INPUT button. 5) Press the up(▲) or down(▼) button to select the On or Off and then press the Menu button to save. 24 …………………………………………………………………….
7-3. Auto switching Time 1) Press the up(▲) or down(▼) button to select the Time. 2) Press the left(◀) or right(▶) button to adjust the Time and then press the MENU button to save. INSTRUCTION MANUAL …………………………………………………………………….
A. Wall mount (Option) 1) Using the 75 mm VESA holes. 2) Using the VESA standard wall mount design and the 75mm hole pattern on the back side to install the LCD monitor to the wall. TRIGGER INPUT AUDIO IN 75mm S-VIDEO IN IN AV1 75mm OUT IN AV2 OUT VGA DC12V 26 …………………………………………………………………….
B. Rack mount (Option) 1) Install the monitor in the Pre-Rack using the 75 mm VESA holes. 2) Install the Pre-Rack in the Open Rack using side mounting holes. ※ The Pre-Rack is available rotation of 360° on the Open Rack. INSTRUCTION MANUAL …………………………………………………………………….
▶ PIN ASSIGNMENTS Pin 1 RED VIDEO 9 2 GREEN VIDEO 10 SIGNAL CABLE DETECT 3 BLUE VIDEO 11 GROUND 4 GROUND 12 SDA(for DDC) 5 GROUND 13 H-SYNC.(or H+V SYNC.) 6 RED GROUND 14 V-SYNC. 7 GREEN GROUND 15 SCL(for DDC) 8 BLUE GROUND ▶ ACCESSORY 1. Power cord 2. Power adaptor 3. User’s manual 4. PC cable 5. Trigger cable (Option) 6. Stereo cable (Option) 7. Wall mount (Option) 8. Rack mount (Option) 28 …………………………………………………………………….
This monitor features a power management system to “power down” upon receipt of the VESA DPMS(The display power management signaling) from a VESA DPMS video card. The VESA DPMS-compliant video card performs this signaling system through not sending horizontal, vertical, or sync signal. This monitor enters an appropriate mode through identifying each of the three modes of the signaling system. POWER CONSUMPTION MODE POWER CONSUMPTION ON < 21W STANDBY < 20.5W SUSPEND < 20.5W ACTIVE OFF < 9.
8RTC LCD-Type 8RTF 8’’ Diagonal AM-TFT(Active-Matrix) 8.4’’ Diagonal AM-TFT(Active-Matrix) Pixel pitch(mm) : 0.2025(H) x 0.2025(V) Pixel pitch(mm) : 0.213(H) x 0.213(V) BRIGHTNESS: 250cd/㎡(Typical) BRIGHTNESS: 600cd/㎡(Typical) CONTRAST RATIO: 500:1(Typical) CONTRAST RATIO: 600:1(Typical) RESPONSE TIME: 25msec(Typical) RESPONSE TIME: 25msec(Typical) RESOLUTION (H x V) 800X600 @60Hz FREQUENCY HORIZONTAL: 37.5KHz, VERTICAL: 60Hz VIDEO(2ch input 1.
WEEE Symbols Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life.
MEMO
Vicon Standard Equipment Warranty Vicon Industries Inc. (the “Company”) warrants your equipment to be free from defects in material and workmanship under Normal Use from the date of original retail purchase for a period of three years, with the following exceptions: 1. 2. 3. 4. 5. 6. 7. 8. 9. VCRs, all models: Labor and video heads warranted for 120 days from date of original retail purchase. All other parts warranted for one year from date of original retail purchase.
Vicon Industries Inc.
