Product specifications

ManualsBrandsVicon ManualsComputer equipmentVDR-404

Vicon part number 8009-8164-10-00 Rev 607 Section 11

XX164-10

MODEL VF-404 SERIES

FOUR-CHANNEL FIBER-OPTIC VIDEO

TRANSMISSION SYSTEM

Product specifications subject to change without notice.

Vicon and its logo are registered trademarks of Vicon Industries Inc.

VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788

TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116

24-Hour Technical Support: 800-34-VICON (800-348-4266)

UK: 44/(0) 1489-566300 WEB: www.vicon-cctv.com

Summary of content (14 pages)

PAGE 1
XX164-10 MODEL VF-404 SERIES FOUR-CHANNEL FIBER-OPTIC VIDEO TRANSMISSION SYSTEM Copyright © 2007 Vicon Industries Inc. All rights reserved. Product specifications subject to change without notice. Vicon and its logo are registered trademarks of Vicon Industries Inc. VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788 TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116 24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: 44/(0) 1489-566300 WEB: www.vicon-cctv.
PAGE 2
PAGE 3
FCC Notice Note: Complies with Federal Communications Commission Rules & Regulations Part 15, Subpart B for a Class A digital device. WARNING This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instruction, may cause interference to radio and television reception.
PAGE 4
Important Safeguards GRAPHIC SYMBOL EXPLANATION The lightening bolt symbol alerts the user to the presence of dangerous voltage that may present the risk of electric shock. 1984, provides information on proper grounding of the leadin wire to an antenna discharge unit, size of grounding conductors and the requirements of grounding electrodes. 14. Lightning - Disconnect the product from its power source and cable system when possible to prevent damage due to lightning and power-line surges. 15.
PAGE 5
Introduction The information in this manual covers the installation of the VF-404 Fiber-Optic Video Transmission System. This system should only be installed by a qualified technician using approved materials and wiring practices in accordance with the National Electrical Code ANSI/NFPA 70, state, and local electrical codes. Read these instructions thoroughly before beginning an installation.
PAGE 6
PAGE 7
Installation Standalone Modules Mount the unit to a secure surface using #8 (3mm) hardware in four places. See the drawing on the next page for mounting dimensions. Be sure to allow sufficient room for the required minimum bend radius of the fiber cable used. Rack-Mount Cards The unit slides into any open slot in the VF-SR-20/2 card cage. Use a small screwdriver to push and lock the two ¼-turn fasteners into place.
PAGE 8
VF-404T Transmitter VF-404R Receiver
PAGE 9
VF-404RR Rack-Mount Receiver VF-404TR Rack-Mount Transmitter Status Indicators Standalone Units The VF-404T transmitter and VF-404R receiver provide the following LED status indicators to aid in installation and troubleshooting: VLI 1 through VLI 4 – VF-404T A green LED indicator is provided for each of the four video channel inputs. Video status associated with each of these LEDs is summarized below.
PAGE 10
OLI – VF-404R A green LED indicator monitors the power of the optical signal that is being received at the receiver. Optical input status associated with this LED is summarized below. Optical Level Indicator Optical Status Green Proper Optical Input Power Present Off Optical Input not Detected Power A green LED indicator monitors the internal voltages created within the unit. Power status associated with this LED is summarized below.
PAGE 11
Shipping Instructions Use the following procedure when returning a unit to the factory: 1. Call or write Vicon for a Return Authorization (R.A.) at one of the locations listed below. Record the name of the Vicon employee who issued the R.A. Vicon Industries Inc.
PAGE 12
Technical Information ELECTRICAL Power Requirements: Current: Power Consumption: Heat Equivalent: Radio Emission Standard: Fiber Type: Standalone: 24 VAC. Rack Mount: power supplied from card cage. Transmitter: 375 mA. Receiver: 330 mA. Transmitter: 5.6 W. Receiver: 5.0 W. Transmitter: 0.321 btu/min (0.08 kg-cal/min). Receiver: 0.282 btu/min (0.07 kg-cal/min). Note: These figures represent the conversion of 100% of the electrical energy to heat.
PAGE 13
Vicon Standard Equipment Warranty Vicon Industries Inc. (the “Company”) warrants your equipment to be free from defects in material and workmanship under Normal Use from the date of original retail purchase for a period of three years, with the following exceptions: 1. 2. 3. 4. 5. VCRs, all models: Labor and video heads warranted for 120 days from date of original retail purchase. All other parts warranted for one year from date of original retail purchase.
PAGE 14
Vicon Industries Inc.