Technical data

3Systemdescription
20 CamTel
svr
Control inputs, error relay, sabotage protection
Control inputs ■ Dependingoncontrolinputfunctionandondeviceconfiguration,events
can be triggered by active switch normally open, active switch normally
closed,edgecontrol,orpermanentcontact.
■ Inprinciple,control inputs must beswitchedtoground.Use the ground
terminalslabelled onthedevice,orthegroundterminalsoftheterminal
blocklabelled"common ground for all inputs of type control input"inthe
tableabove.
■ Statuschangesatthecontrolinputs-closingandopeningofthecontact-
10 Auxin1 Control
input
Sabotageinputfordialupwithautomaticswitchingofvideo
input1(V1in)toaCamControlreceiverunit.
Note: The operation of this input is independent of the status of
the arm/disarm enable input "Al. a/d"
11
to
15
Controlin1-2for
CamTel
svr
4
Controlin1-5for
CamTel
svr
10
Control
input
Cameracontrolinputsforexternalcontacttriggeredrecording
and/orselectivedialuptoaCamControlreceiverunitforvideo
inputs1and2or1to5.Thesecontrol inputscanbeusedfor
eventrecordingaswellasforeventoptimisedpermanentlong-
termrecording.
16 Ground Commongroundforallinputsof
type"controlinput"
17 Ground Commongroundforallinputsoftype"controlinput"
18 12VDC+Power,
+
Supplyvoltageis12VDC.Onlyconnectthedevicetoyourlocal
powersupplysystemusingtheprovidedpowersupplyunitwith
thepreparedconnectioncable.Onlyusethepowersupplycable
matchingyourgrid
(Euro/UK).
19 12VDC  Power,
ground
20 R1[Common] Relay Deviceconfigurationallowsyoutoallocatethefollowing
functionstoanyrelay:
■ Manual remote control with CamControl LITE,
CamControl PRO or CamControl CLIENT distinguishing
betweenswitchandpushbuttonfunctions
■ Switching to at least one CamControl receiver unit with
activeonlineconnection
■ Errorrelay
21 R1[normallyopen] Relay
22 R1[normally
closed]
Relay
23 R2[Common] Relay
24 R2[normallyopen] Relay
25 R2[normally
closed]
Relay
26 Auxin2 Control
input
Auxiliaryinput2:Reserved
27 Ground Commongroundforallinputsoftype"controlinput"
28
to
32
Controlin3-4for
CamTel
svr
4;
Controlin6-10for
CamTel
svr
10
Control
input
Cameracontrolinputsforexternalcontacttriggeredrecording
and/orselectivedialuptoaCamControlreceiverunitforvideo
inputs3and4or6to10.Thesecontrol inputscanbeusedfor
eventrecordingaswellasforeventoptimisedcontinuous
recording.
33 Speaker+ Audio IfyourCamTel
svr
isequippedwithanAudio Card ,usethis
outputforconnectingaloudspeakerwith1W/8Ohmfor
audioreproductionattheobjectofobservation.Theoutputis
protectedagainstoverload,butnotagainstshorts.Usinga
speakerwithmatchingmaximumoutputisrecommended.
34 Speaker- Audio
⊥
⊥
⊥
⊥
⊥