Vicon Industries Inc. Does not warrant that the functions contained in this equipment will meet your requirments or that the operation will be entirely error free or perform precisely as discribed in the documentation. This system has not been designed to be used in life critical situations and must not be used for this purpose. Copyright © 2006 Vicon Industries Inc. All rights reserved. Product specifications subject to change without notice.
Dear Customer! By selecting this VICON product you have chosen a professional device which guarantees highest possible quality and reliability. We like to thank you very much for your confidence in our products and kindly ask you to read the following instructions carefully before commissioning the product in order to be able to take full advantage of all quality features regarding this product line.
GENERAL INFORMATION General Information Safety Precautions * Read these instructions carefully before commissioning the camera in order to avoid damages caused by improper installation or use. * Installation may only be carried out by authorised personnel according to the local safety regulations. * Operate the camera with the designated voltage only. * Follow the safety instructions attached to the camera. * Never use the camera for other purposes than designated.
MOUNTING THE CAMERA Mounting the Camera Mounting the Camera to a Wall Mount -4-
COMMISSIONING THE CAMERA Commissioning the Camera Tips for Camera Location 1.0 To avoid internal overheating: - never expose the camera to direct sunlight without additional camera housing - keep sufficient distance to direct heat sources. 2.0 Never install the camera at humid, oily or dusty locations without using an additional housing. (without additional housing the camera is not suitable for outdoor use!) 3.0 The camera should be installed out of reach (min. height: 2.30 m) 4.
COMMISSIONING THE CAMERA Adjustment of Back Focus This adjustment should only be carried out, if the lens cannot be focused properly using the lens focus ring. For such a case proceed as follows: 1 Loosen the Allan head screw with the attached Allan head key. For large distances, turn the focus ring of the lens almost (0.5 cm) to the "endless" limit position. If you need to focus an object near the camera, turn the focus ring of the lens to a position 1cm before the "near" limit position.
COMMISSIONING THE CAMERA Focusing the Camera Lens After you have selected the correct picture detail you have to adjust the lens focus. The focus adjustment needs to be done with the iris fully open, since the camera has the smallest depth of focus in this position. If the focus adjustment was not done with the iris completely open, the picture would be sharp during the day but slowly getting out of focus the more the light disappears.
COMMISSIONING THE CAMERA Circuit points and operation 1 2 1. Lens connector 2. Menu buttons DC - Lens 1. Controll 2. Controll + 3. Drive+ 4. Masse Attention: This camera comes with a four times electronic zoom. With the buttons Ý(Tele) and ß(Wide) you can operate the zoom function.
COMMISSIONING THE CAMERA Rear View Rear View IX 4000H ELC DC V-Phase Rear View IX 4000L ELC 1 DC V-Phase 2 Control Control 3 4 AC 24V/ DC12V 5 1. 2. 3. 4. 5. FG Auto Shutter / DC Lens LL Phasen adjust Control (Remote) Connector Video Out Power input Remote Jack PC Interface RS 232C PC Connector RS 232/ RS 485 Converter -9- Belegung: 1. Frame GND 2. RD 3. TD 4. DTR 5. Signal GND 6. DSR 7. RTS 8. CTS 9.
COMMISSIONING THE CAMERA Camera Configuration Menu: GENERAL AWB AE D&N WDR PRIVACY DISPLAY INITIAL EXIT CAMERA ID ZONE LABEL NEGA/POSI SHARPNESS MIRROR FREEZE INITIAL EXIT WB MODE RED CONT BLUE CONT PUSH AUTO INITIAL EXIT BRIGHTNESS FLICKERLESS SHUTTER SPD AGC MAX SET MAX FLD SET INITIAL EXIT D/N MODE LEVEL FILTER DLY INITIAL EXIT WDR MODE WDR LEVEL BACK LIGHT BLC LEVEL INITIAL EXIT AREA MASK START X END X START Y END Y INITIAL EXIT CAMERA ID ZONE LABEL VERSION INITIAL OFF STATE 000 ~ 255 SET POSI
COMMISSIONING THE CAMERA Setting Up The Menu Press the MENU button to access the GENERAL mode. Chage menu Point using the UP and Down buttons. Change the status using the the LEFT / RIGHT buttons. CAMERA ID ZONE LABEL NEGA/POSI SHARPNESS MIRROR FREEZE INITIAL EXIT General 000 SET POSI 7 NORMAL OFF OFF Camera ID: In this Menu a number can be assigned to the camera (000 bis 255) wich will be displayed on the monitor. Therefor the function CAMERA ID must be switched on in the DISPLAY MENU.
COMMISSIONING THE CAMERA WB MODE RED CONT BLUE CONT PUSH AUTO INITIAL EXIT AWB AUTO NOT USE NOT USE NOT USE OFF WB MODE: The following „White Balance“ functions can be selected: AUTO: White Balance is automatically set between 2500°K~9500°K HOLD: If PUSH AUTO is selected as ON, it fixes up the value setting the current WB USER: Manual WB.
COMMISSIONING THE CAMERA AGC MAX SET: OFF: AGC deactivated LOW: Gain is increased or decreased from 0 to 10dB automatically according to the illumination. MID: Gain is increased or decreased from 0 to 20dB automatically according to the illumination. High: Gain is increased or decreased from 0 to 30dB automatically according to the illumination.
COMMISSIONING THE CAMERA WDR MODE WDR LEVEL BACK LIGHT BLC LEVEL INITIAL EXIT WDR OFF 9 OFF 10 OFF WDR MODE: ON / OFF WDR LEVEL: This value sets the level of the WDR regulation. 0 ~ 15 Ranged and adjust the brightness in WDR Mode. BACK LIGHT: ON / OFF BLC LEVEL: With this value the BLC Gain will be set. 0 ~ 15 Ranged and adjust the BLC Gain.
COMMISSIONING THE CAMERA END X: Indicates the ending point on X axis. START Y: Indicates the starting point on Y axis. END Y: Indicates the ending point on Y axis. INITIAL: INITIAL PRIVACY MODE EXIT: RETURN to MAIN MENU CAMERA ID ZONE LABEL VERSION INITIAL EXIT Display OFF OFF 1.0 OFF CAMERA ID: To activate the CAMERA ID, so that this becomes visible on the screen. ZONE LABEL: To activate the 10-figure name of the camera, so that this becomes visible on the screen.
EXHIBIT Exhibit Troubleshooting Error Cause No picture - No operating voltage (check red LED) Coaxial connection interrupted (check video cable) The picture is noisy - Insufficient light The lens drive of the used lens (DC / AI) is not properly adjusted to the camera (level too low) The picture is too bright - The lens drive of the used lens (DC / AI) is not properly adjusted to the camera (level too high) Too much peak light; change camera location or activate backlight function of the camera
TECHNICAL SPECIFICATIONS Technical Specifications Model IXION 4000L / H (PAL) CCD SENSOR 2:1 Interlace transfer 1/3“ Double Scan CCD Effective Pixels 752 (H) x 582 (V) Reolution Onscreen Display 480 TV-Lines 0,1Lux (Normal Mode) 0.
CLEANING AND CARE & TECHNICAL SUPPORT Cleaning and Care Before you start to clean the camera body, disconnect the unit from power supply. For reasons of electrical safety never clean the camera with water or other liquid matters and never put the camera under water. To clean use a soft dry cloth. Cleaning the camera inside is strictly forbidden and may only be done by your authorised dealer.
SHIPPING INSTRUCTIONS Shipping Instructions: Use the following procedure when returning a unit to the factory: 1. Call or write Vicon for a Return Authorization (R.A.) at one of the locations listed below. Record the name of the Vicon employee who issued the R.A. Vicon Industries Inc.
Vicon Industries Inc.
