User guide

Hewlett-Packard SCSI-Fibre Channel Router Installation and User Guide
Revision 2.1.0 Page
14
5. Ensure that the host sees all the device(s) on the router's SCSI bus by forcing a SCSI
I/O scan. Refer to the host's manual for further information if necessary.
Example (for HP e3000):
ISL>help
ISL>ode (offline diagnostic environment)
ODE>mapper
Mapper>run
10 I/O adapter
10/16 Upper Bus Converter
10/16/12 HP-PB Fast Wide SCSI
10/16/12.0.0 A6188A
10/16/12.0.1 A6188A
10/16/12.0.2 A6188A
10/16/12.0.3 A6188A
10/16/12.0.4 A6188A
10/16/12.0.5 A6188A
10/16/12.0.6 A6188A
10/16/12.0.7 A6188A
10/16/12.1.0 OPEN-3
10/16/12.1.1 OPEN-3
10/16/12.1.2 OPEN-3
10/16/12.1.3 OPEN-3
10/16/12.1.4 OPEN-3
10/16/12.1.5 OPEN-3
10/16/12.1.6 OPEN-3
10/16/12.1.7 OPEN-3
10/16/12.2.0 OPEN-3
10/16/12.2.1 OPEN-3
10/16/12.2.2 OPEN-3
10/16/12.2.3 OPEN-3
10/16/12.2.4 OPEN-3
10/16/12.2.5 OPEN-3
10/16/12.2.6 OPEN-3
10/16/12.2.7 OPEN-3
10/16/12.3.0 OPEN-3
10/16/12.3.1 OPEN-3
10/16/12.4.0
10/16/12.5.0
10/16/12.6.0
10/16/12.8.0
10/16/12.9.0
10/16/12.10.0
10/16/12.11.0
10/16/12.12.0
10/16/12.13.0
10/16/12.14.0
10/16/12.15.0
. . . . .
mapper>exit
ode>exit
ISL>start norecovery group=config
NOTE: The router will respond to all SCSI target INQUIRES without a device being configured as
demonstrated in the above ODE listing. Make sure you see the product ID's from the device(s) being
displayed.
6. If the host has seen all the device(s), then the installation is successful and normal
operation may begin.
Router Map
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
2.0
2.1
2.2
2.3
2.4
2.5
2.6
2.7
3.0
3.1
3.2
3.3
3.4
3.5
3.6
3.7
-
-
-
-
15.7
VA7100
FF.00
FF.01
FF.02
FF.03
FF.04
FF.05
FF.06
FF.07
XP512
FF.00
FF.01
FF.02
FF.03
FF.04
FF.05
FF.06
FF.07
FF.08
FF.09
FF.0A
FF.0B
FF.0C
FF.0D
FF.0E
FF.0F
FF.10
FF.13
Note
FC address holes are filled
with next available address.
So don’t make holes.