Installation & Assembly

ManualsBrandsVibia ManualsLightingWireflow Lines 6-Light LED Pendant Lamp

TECHNICAL SPECIFICATIONS

ESPECIFICACIONES TÉCNICAS TECHNISCHE DATEN

0325 0330 0332 0338 0340

Lighting fixture / Estructura luminaria / Leuchten-Struktur

1 un. 1 un. 1 un. 1 un. 1 un.

Lineal rod 9 cm / Varilla largo 9 cm / Stäbe Länge 9 cm

-- -- -- -- 4 un.

Lineal rod 16 cm / Varilla largo 16 cm / Stäbe Länge 16 cm

-- -- -- -- 2 un.

Lineal rod 26 cm / Varilla largo 26 cm / Stäbe Länge 26 cm

6 un. 10 un. 10 un. -- --

Lineal rod 28 cm / Varilla largo 28 cm / Stäbe Länge 28 cm

-- -- -- -- 4 un.

Lineal rod 31 cm / Varilla largo 31 cm / Stäbe Länge 31 cm

-- -- -- -- 2 un.

Lineal rod 33 cm / Varilla largo 33 cm / Stäbe Länge 33 cm

-- -- -- 2 un. --

Lineal rod 62 cm / Varilla largo 62 cm / Stäbe Länge 62 cm

3 un. 5 un. 5 un. -- --

SUPPLIED MATERIAL MATERIAL SUMINISTRADO

GELIEFERTES MATERIAL

Wireflow

Design by Arik Levy

ASSEMBLY INSTRUCTIONS INSTRUCCIONES DE MONTAJE MONTAGEANLEITUNG

Summary of content (8 pages)

PAGE 1
Wireflow Design by Arik Levy ASSEMBLY INSTRUCTIONS SUPPLIED MATERIAL INSTRUCCIONES DE MONTAJE MONTAGEANLEITUNG MATERIAL SUMINISTRADO GELIEFERTES MATERIAL 2. 1.
PAGE 2
ASSEMBLY INSTRUCTIONS INSTRUCCIONES DE MONTAJE MONTAGEANLEITUNG EN 1 IMPORTANT NOTICE: Switch off the mains before installing the lamp. 1. Remove the profile (A) and track (B) from the ceiling profile 2. Position the profile (A) and mark the fixing points on the ceiling. The adjacent drawings indicate the distances between the fixing points as well as the general dimensions of the ceiling profile. ES IMPORTANTE: Desconectar el suministro eléctrico antes de realizar la instalación de la luminaria. 2 1.
PAGE 3
ASSEMBLY INSTRUCTIONS 3 INSTRUCCIONES DE MONTAJE MONTAGEANLEITUNG EN 3. Drill the holes as indicated on the marked points. 4. After threading the installation electrical cable through its corresponding hole fix ceiling profile (A) in place using the appropriate screws and plugs (not supplied). 5. Connect the lamp to the electrical mains via the connectors (C) as shown in drawing No. 6. ES 3. Realizar los taladros en los puntos marcados. 4.
PAGE 4
ASSEMBLY INSTRUCTIONS INSTRUCCIONES DE MONTAJE MONTAGEANLEITUNG EN 6 DALI SYSTEM DIMMING Diagram X REGULACIÓN MEDIANTE SISTEMA DALI Diagrama X DIMMBAR MIT DALI-SYSTEM Anschlussschema X 6. Dimmable with the DALI system: Connect terminal L, N, T/T, while connecting the DALI control digital signal lines at terminals 1 and 2 (see diagram X). Dimmable 1-10V: Connect terminal N and T/T at the terminals as shown, while connecting the line running through the dimmer in your installation at terminal L.
PAGE 5
ASSEMBLY INSTRUCTIONS INSTRUCCIONES DE MONTAJE MONTAGEANLEITUNG EN 7 7. Connect the cable jack (D) to the socket 8. Attach the track (B) to the ceiling profile (A). Insert the pivots and adjust to abut. The structure is now held in place. ES 7. Conectar la regleta (D) en el bloque de conexión. 8. Montar el carril (B) en el perfil techo (A). Insertar los pivotes y desplazar por el alojamiento hasta hacer tope. De esta forma queda sustentada toda la estructura. D 7.
PAGE 6
ASSEMBLY INSTRUCTIONS INSTRUCCIONES DE MONTAJE MONTAGEANLEITUNG EN 9 9. Each of the spotlights is wrapped up. Remove the outer plastic bags and unroll the cable. Do not remove the protective profile (E). FITTING THE RODS 10. The rods are secured by the pieces (F) fitted to the cable. They leave the factory adjusted to the correct height. First, insert the piece (F) in the hook on the rod and then turn it 90º to secure it. 11.
PAGE 7
ASSEMBLY INSTRUCTIONS 11 INSTRUCCIONES DE MONTAJE MONTAGEANLEITUNG Ref.: 0330 Ref.: 0332 CORRECT Ref.: 0338 NOT CORRECT 1st Lineal rod 33 cm.
PAGE 8
ASSEMBLY INSTRUCTIONS 11 Ref.: 0340 INSTRUCCIONES DE MONTAJE MONTAGEANLEITUNG EN 12. After installation is complete, remove the protective profile (E) from each of the spotlights by hand, breaking each profile along the pre-cut line. ES 12. Al terminar completamente la instalación, retirar el perfil de protección (E) de cada uno de los focos, con las manos, rompiendo por la zona pre-cortada. D 12.