User guide

100C Air Compressor Kit
MOUNTING AND WIRING
1. Disconnectgroundcablefromvehicle’sbattery.
2. Temporarily position the air compressor in the location where it will be mounted.
3. Routegroundwiretothenegativepostofthebatteryortoanappropriategroundingpoint
and cut ground wire to length as needed.
4. Mountaircompressorwiththefoursetsofbolts,nuts,washers,andlockingwashersprovided.
 (SeeFig.2forMountingInstructions)
5. RefertoRemoteAirFilterInstallationInstructionincludedintheRemoteInletAirFilterPackfor
 installationofRemoteInletAirFilter.
6. Thisaircompressormaybeequippedwithaheatresistantleaderhose.(NotapplicabletoP/Ns
 10014or10016)Thisleaderhoseisdesignedtoprolongthelifeofyourairline.Donotremove
this leader hose from air compressor.
7. Pleasenote,theleaderhosethatcamewithyourcompressormayhaveabuilt-ininlinecheck
 valveinstalled.Donotremoveinlinecheckvalvefromleaderhoseifsoequipped.
8. Ifequipped,selectaproperlocationtomountleaderhosewithhosebracketprovided.Avoid
locations where leader hose may become tangled with wires and other hoses.
9. To mount hose bracket, drill hole with 3/16” drill bit and push self–anchoring hose bracket pin
 intohole.Routeleaderhosethroughhosebracketandsecurehosebypressingbracketclamp
into locked position.
10.Toremovehosefromthehosebracket,simplypressdownonthehoseclampreleasetabto
release bracket clamp. (Fig. 3)
11.Connectcompressorpositiveleadwiretooneoftheleadsofyourpressureswitch.
12.Makesurethatyourcompressorsetupisproperlyfused.Forappropriatefusesize,refertoamp
 drawofcompressorintheSpecicationssectionofthismanual.
13.Alwayslocatefuseascloseaspossibletopowersource.
14. Before connecting to power source, re-check to make sure that all connections
are properly connected.
15.Connectandtestcompressorsystembyrunningthecompressorforashorttimetobuildup
pressure in your air tank.
16. Once air pressure reaches preset cut out pressure of your pressure switch, the compressor
will shut off. Inspect all air line connections for leaks with soap and water solution. If a leak
 isdetected,theairlinemaynotbecutsquarelyorpushedallthewayin.Tightenconnections
if needed.
(Fig. 1) Standard 100C Air Compressor Kit Installation Parts List:
A.HoseBracket(1pc)(10010)
B.MountingBolts(4pcs)
C.FlatWashers(8pcs)
D.LockingWashers(4pcs)
E.Nuts(4pcs)
F.1/4”NPTFx1/4”BarbedFitting(1pc)(10010)
G.1/4”AirLine(1pc)(10010)
H.AirLineClips(3pcs)(10010)
I. Screws (3pcs) (10010)
J.RemoteInletAirFilterwithFilterElement(1pc)(10010)
(Fig. 2) Compressor
Mounting Hardware
B.MountingBolt
C.FlatWasher
D.LockingWasher
E.Nut
K. Vibration Isolator
USER MANUAL
B
A
C D E
F
H
I
J
(Fig. 3) Leader Hose Bracket
L.HoseClamp
M.ClampReleaseTab
N.SelfAnchoringPin
B
C
C
D
E
K
L
M
N
G