I The ENDAT-7100M System Board ENDAT-7100M User Manual PCB version: A5 or later May.16.
User Manual Copyright Notice The content of this manual has been checked for accuracy. The manufacturer assumes no responsibility for any inaccuracies that may be contained in this manual. The manufacturer reserves the right to make improvements or modification to this document and/or the product at any time without prior notice.
III The ENDAT-7100M System Board Specification: Model ENDAT-7100M Form Factor System Chipset Mini-ITX 170 mm x 170 mm (6.69”x6.69”) with 6 layers PCB VIA CN700(NB/2.5W)+ VIA VT8237R Plus (SB/1.8W) VIA Eden ULV 500MHz (1W) VIA Eden 1.0GHz (5W) VIA C7-D 1.
IV User Manual TABLE OF CONTENTS CHAPTER 1. INTRODUCTION ...................................................... 1 1-1. 1-2. 1-3. 1-4. FEATURES .............................................................................................. 2 UNPACKING ............................................................................................ 3 ELECTROSTATIC DISCHARGE PRECAUTIONS ................................... 3 MOTHERBOARD LAYOUT ......................................................................
V The ENDAT-7100M System Board CHPATER 4. VGA, LCD, FEATURE............................................. 30 4-1. VGA FEATURE....................................................................................... 30 4-2. LVDS PANEL FEATURE......................................................................... 31 4-3. DRIVER UTILITY INSTALLATION GUIDE.............................................. 32 CHPATER 5. LAN ADAPTER ....................................................... 34 5-1. FEATURES ..........
1 The ENDAT-7100M System Board Chapter 1. Introduction ENDAT-7100M supports high performance processor of VIA C7 processor. It also supports high speed DDR memory with 64-bit wide interfaces with non-ECC DIMM (up to 1GB). Only Double Data Rate (DDRII) SDRAM memory is supported and the speed of memory can be 400 and 533 MHz. ENDAT-7100M provides an integrated graphics (S3 Graphics UniChrome™ Pro IGP) accelerator delivering cost competitive 3D, 2D, and video capabilities.
User Manual 1-1. Features Basic Feature: Board format: Mini-ITX (170mm x 170 mm) Supports 400/533 MHz FSB by VIA C7® Digital I/O: 8 bits input and 8 bits output (5V) Supports DDRII 400/533 MHz SDRAM up to 1GB Serial ATA connector x 2 Enhance 40 Pin IDE connector x 1; 44 Pin IDE connector x 1 Multiple I/O ports: COM port x 4; USB (2.
3 The ENDAT-7100M System Board 1-2. Unpacking The motherboard comes securely packaged in a sturdy cardboard shipping carton. In addition to the User's Manual, the motherboard package includes the following items: ENDAT-7100M System Board SATA / IO Cables / DC Power Cable CDROM Driver includes: Drivers for Windows 2000, XP and AMI/AWARD FLASH ROM utilities. If any of these items are missing or damage, please contact the dealer from whom you purchase the motherboard.
User Manual 1-4.
5 The ENDAT-7100M System Board Chapter 2. Setting up the Motherboard 2-1. Jumpers and Connectors Jumpers/Connectors Overview: Function Power Supply Connector 2 pin wafer Output Power for Hard Disk Cooling Fan Connector Buzzer Battery Clear CMOS DDR2 SDRAM socket LVDS Panel Connector LVDS Voltage Selector LCD Backlight Voltage Selector LCD Backlight Control Voltage Selector LCD Backlight Voltage (for +3.
6 User Manual Function RS232 / 422/ 485 Selector for COM2 SMBus PCI SLOT DIGITAL I/O Pin Header LPT1, LPT2 SATA 1, SATA 2 40-Pin IDE Connector 44-Pin IDE Connector LINE OUT / CD IN Pin Header MIC IN / LINE IN Pin Header LINE OUT Connector SPDIF Pin Header DIMM Power LED System Power LED Jumpers/Connectors JP3 & JP4 JP5 PCI1 JP7 LPT1, LPT2 SATA1, SATA2 IDE1 IDE2 JP8 JP9 CN9 SPDIF1 LED1 LED2 Please double-check the insertion and orientation of the LCD cable before applying power.
7 The ENDAT-7100M System Board JP10: Pin Header for Case Panel (2.54mm) Pin No. Function 1(-), 2(+) HDD active LED 3,6 External Speaker 4,5 Buzzer On/Off 7,8 Hardware Reset Switch 9,10 ATX Power On/Off 11(-),12(+) Power LED 13,14 Close: Enable WDT function JP3, JP4: RS232 / 422 / 485 Selector for COM2 (2.0mm) TYPE JP3 (2x3/2mm) JP4 (3x4/2mm) RS-232 * 1-2 1-2, 4-5, 7-8, 10-11 RS-422 3-4 2-3, 5-6, 8-9, 11-12 RS-485 5-6 2-3, 5-6, 8-9, 11-12 JP6: COM Port Voltage Selector (2.0mm) Voltage +12V(DC) R.I.
User Manual JP7: DIGITAL I/O Pin Header Connector (2.0mm) Pin No. Function Pin No. Function 1 +5V 2 +5V 3 DIO-O0 4 DIO-I0 5 DIO-O1 6 DIO-I1 7 DIO-O2 8 DIO-I2 9 DIO-O3 10 DIO-I3 11 DIO-O4 12 DIO-I4 13 DIO-O5 14 DIO-I5 15 GND 16 GND 17 DIO-O6 18 DIO-I6 19 DIO-O7 20 DIO-I7 21 +3.3V 22 +3.3V JP8: LINE OUT & CD IN Pin Header Connector (2.54mm) Pin No. Function Pin No. Function 1 LO_J_R 2 CDL 3 GND_AUD 4 CDGND 5 GND_AUD 6 CDGND 7 LO_J_L 8 CDR JP9: Microphone IN & LINE IN Pin Header Connector (2.54mm) Pin No.
9 The ENDAT-7100M System Board CN5: CRT Box Header Connector (2.0mm) Pin No. Description Pin No. Description 1 RED 9 n/c / +5V 2 GREEN 10 GND 3 BLUE 11 n/c 4 n/c 12 DDC DAT 5 GND 13 H-Sync 6 GND 14 V-Sync 7 GND 15 DDC CLK 8 GND CN8: Box Header Type Connector for COM4 port (RS-232) (2.54mm) Pin No. Function Pin No. Function 1 DCD 6 DSR 2 RXD 7 RTS 3 TXD 8 CTS 4 DTR 9 RI 5 GND 10 n/c D-SUB Type Connector for COM1 ~ COM3 port (RS-232) Pin No. Description Pin No.
User Manual D-SUB Type Connector for COM2 port (RS-485 2 Wire) Pin No. Function Pin No. Function 1 Data – 6 NA 2 NA 7 NA 3 Data + 8 NA 4 NA 9 NA 5 NA SPDIF: SPDIF Pin Header Connector (2.0mm) Pin No. Function 1 +5V 2 n/c 3 SPDIFOUT 4 GND 5 SPDIFIN JP5: SM Bus Pin Header Connector (2.0mm) Pin No. Function 1 SMBCK 2 SMBDT 3 +3.3V 4 GND JUSB1 JUSB2: Pin Header Type Connector for USB port (2.54mm) Pin No. Function Pin No.
11 The ENDAT-7100M System Board J1: Power Supply Connector 2 pin wafer (3.96mm) Pin No. Function Pin No. Function 1 +12V 2 GND HDDPWR: Output Power for Hard Disk (3.96mm) Pin No. Function Pin No. Function 1 +5V(Red) 2 GND 3 GND 4 +12V(Yellow) IDE1: IDE1 Connector (40Pins) Pin No. Description Pin No.
User Manual LPT2: Printer (LPT2) Port Box Header (2.0mm) Pin No. Description Pin No. Description 1 STB# 10 ACK# 2 PD0 11 BUSY 3 PD1 12 PE 4 PD2 13 SLCT 5 PD3 14 AFD# 6 PD4 15 ERR# 7 PD5 16 INIT# 8 PD6 17 SLIN# 9 PD7 18-25 GND IDE2: Slim IDE2 Connector (44Pins2.0mm) Pin No. Description Pin No.
13 The ENDAT-7100M System Board LVDS1: Dual LVDS Channel (1.25mm) Pin No. 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 Signal VBL (+12V) GND DISP.ON/OFF LCD Power GND TxO0+ TxO1+ TxO2+ TxO3+ TxOC+ GND TxE0+ TxE1+ TxE2+ TxE3+ TxEC+ LCD Power GND GND VBL (+12V) Pin No.
User Manual 14 2-2. Installing Memory ENDAT-7100M system board offers one 240 pin DDRII SDRAM socket supports up to 1GB memory and the speed can be 400 and 533 MHz. Note: For DIMM compatibility, please refer to page 40. 2-3. Shared VGA Memory ENDAT-7100M is using built-in AGP VGA controller with S3 Graphics UniChrome Pro IGP graphics core up to 64MB of system memory. The amount of video memory on motherboard determines the number of colors and the video graphic resolution. 2-4.
15 The ENDAT-7100M System Board IRQ 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Status Used Used Used Used Used Used Used Used Used Used Used Used Used Used Used Used Assignment Timer Keyboard Second 8259 COM2 COM1 COM3 Floppy Disk LPT1 RTC LPT2 or Audio COM4 LAN Adapter (on board) PS/2 Mouse Coprocessor Hard Disk (IDE 1) Reserved (IDE 2) 2-5. Watch dog Timer Watch dog Timer (WDT) is a special design for system monitoring to secure the system work normally.
User Manual 16 Program Sample #include #include #include
17 The ENDAT-7100M System Board 2-6. Digital I/O 1) Pin out of digital I/O header (JP7): Pin No. 1 3 5 7 9 11 13 15 17 19 21 Function +5V DIO-O0 DIO-O1 DIO-O2 DIO-O3 DIO-O4 DIO-O5 GND DIO-O6 DIO-O7 +3.3V Pin No. 2 4 6 8 10 12 14 16 18 20 22 Function +5V DIO-I0 DIO-I1 DIO-I2 DIO-I3 DIO-I4 DIO-I5 GND DIO-I6 DIO-I7 +3.3V 2) Digital I/O port address: This function is support by onboard super I/O chip; it can be control easily by change the register of super I/O chip via I/O port “4Eh” and “4Fh”.
18 User Manual Sample code for Output (using Turbo C/C++ 3.
19 The ENDAT-7100M System Board Chapter 3.
20 User Manual 3-1. Standard CMOS Features The Standard Setup is used for the basic hardware system configuration. The main function is for Data/Time and Hard Disk Drive settings. Item Available Options: Date (mm:dd:yy) Time (hh:mm:ss) IDE Channel 0 Master: IDE Channel 0 Slave : IDE Channel 1 Master: IDE Channel 1 Slave : IDE Channel 2 Master : IDE Channel 3 Master : Video Halt On Auto Auto Auto Auto Auto Auto EGA/VGA All , But Keyboard ․Video Select the type of primary video subsystem.
21 The ENDAT-7100M System Board 3-2. Advanced BIOS Features This section allows you configuring your system for basic operation. You have the opportunity to select the system’s default speed, boot-up priority, keyboard operation and security.
22 User Manual DRAM Clock/Drive Control Item Current FSB Frequency Current DRAM Frequency DRAM Clock DRAM Timing Available Options: By SPD Auto By SPD ․DRAM Clock This item allows you to set the speed of Direct Memory Access (DMA) at either equal to or one-half of the SYSCLK (system clock signal) speed. ․DRAM Timing The value in this field depends on performance parameters of the installed memory chips (DRAM).
23 The ENDAT-7100M System Board ․Select Display Device This field is used to select the type of display to use when the system boots.
24 User Manual VIA OnChip IDE Device Item OnChip SATA SATA Mode OnChip IDE Channel0 OnChip IDE Channel1 IDE Prefetch Mode Primary Master PIO Primary Slave PIO Secondary Master PIO Secondary Slave PIO Primary Master UDMA Primary Slave UDMA Secondary Master UDMA Secondary Slave UDMA IDE HDD Block Mode Available Options: Enabled IDE Enabled Enabled Enabled Auto Auto Auto Auto Auto Auto Auto Auto Enabled ․SATA Mode These fields are used to select the RAID/IDE mode of the serial ATA drives.
25 The ENDAT-7100M System Board VIA OnChip PCI Device Item VIA AC97 Audio VIA OnChip LAN Onboard LAN Boot ROM OnChip USB Controller OnChip EHCI Controller USB Emulation USB Keyboard Support Available Options: Enabled Enabled Disabled All Enabled Enabled ON Enabled ․VIA AC97 Audio Allow the motherboard's BIOS to detect whether you are using any audio device. If an audio device is detected, the onboard audio Codec will be enabled; if no audio is detected, the onboard audio Codec will be disabled.
26 User Manual SuperIO Device Item Onboard Serial Port 1 Onboard Serial Port 2 UART Mode Select RxD, TxD Active IR Transmission Delay UR2 Duplex Mode Use IR Pins Onboard Parallel Port Parallel Port Mode EPP Mode Select ECP Mode Use DMA Available Options: 3F8/IRQ4 2F8/IRQ3 Normal Hi,Lo Enabled Half IR-Rx2Tx2 378/IRQ7 Normal EPP1.9 3 ․UART Mode Select Select an operating mode for the serial port. ․Parallel Port Mode Set the parallel port mode.
27 The ENDAT-7100M System Board IRQ/Event Activity Detect Press Enter ․ACPI Function This function should be enabled only in operating systems that support ACPI. Currently, only Windows® 98SE/2000/ME/XP supports this function. When this field is enabled, the system will ignore the settings in the “Suspend Mode” and “HDD Power Down” fields. If you want to use the Suspend to RAM function, make sure this field is enabled then select“S3 (STR)” in the field below.
28 User Manual and “PS2MS Wakeup from S3/S4/S5” will be disabled while changing the password. 3-6. PnP/PCI Configurations This section describes the configuration of the PCI bus system. PCI is a system that allows I/O device to operate at speeds nearing the speed of the CPU itself, when communicating with its own special components. This section covers some very technical items. It is strongly recommended that only experienced users make any changes to the default settings.
29 The ENDAT-7100M System Board 3-7. PC Health Status This screen shows the information of temperature, Fan speed and Vcore etc. It also can set CPU warning temperature to protect CPU. PC Health Status Item Current System Temp. Current CPU1 Temperature Current CPUFan1 Speed Current CPUFan2 Speed Vcore +3.3V +5V +12 V VBAT (V) 5VSB (V) Available Options: 3-8.
User Manual 30 Chapter 4. VGA, LCD Feature 4-1. VGA Feature ENDAT-7100M provides integrated S3 Graphics UniChrome™ Pro IGP, featuring a 2D/3D AGP8X graphics core with integrated MPEG-2 decoding for smooth DVD and digital video playback, the VIA C7® processing platform also features support for high bandwidth DDRII 400/533 memory, motion compensation and DuoView for the latest multiple format flat panel display devices.
31 4-2. The ENDAT-7100M System Board LVDS Panel Feature The on-board graphic controller supports industry standard LCD panel, LVDS interface only, with 1 channel (18 or 24) and 2 channels (36 or 48bit) data width. LVDS interface provides low voltage, high speed and low EMI serial DC-balanced differential data via optional onboard LVDS. The flat panel interface provides or supports following functions for various panels: - Generates LVDS flat panel channels like clock and data channel.
User Manual 4-3. 32 Driver Utility Installation Guide 1. When finishing the installation of Windows platform (2000/XP), please install the relative VIA driver (4in1) utilities for compliance compatibility of hardware environment. 2. Insert the support CD that supplied with motherboard into CD-ROM driver which enable the access with auto-run mode; or double –click the CD driver icon in “My Computer” to bring up the screen. 3. Select correct motherboard to install driver / utility for the system 4.
33 The ENDAT-7100M System Board 5. The Screen will appear VIA 4in1 driver setup screen, please press “NEXT” to continue. Please follow the steps instructed by each screen for the installation of the VIA 4in1 driver. Restart the system after completed the installation. 6. After installing the VIA 4in1 driver, please select VGA driver for install. The system will request for “restart” after the completion of the driver installation. 7.
User Manual 34 Chapter 5. LAN Adapter The on-board LAN adapter integrated of Single Chip Fast Ethernet Controller with options of one or dual LAN solution, and also the LAN chip option of VIA VT6103 solution. It is highly integrated and requires no “glue” logic external memory on board. It runs in the bus master mode and directly sending/receiving Ethernet packet to/from memory. The On-board LAN adapter can directly fetch the system CPU.
35 The ENDAT-7100M System Board 5-2. UTP Cable / RJ-45 Jack Definition Straight through twisted pair cable is typically used to connect a hub to a server or workstation. In a straight through connection, Pin 1 at the server, Pin 2 at the hub connects to Pin 2 at the server, and so on. Figure A-1 shows the locations of pins on a standard RJ-45 plug on a twisted-pair cable. Table A-1 shows the wiring in a straight-through twisted-pair cable (Pins 4, 5, 7 and 8 are not used).
User Manual 36 5-3. Connecting 100Base-TX Fast Ethernet Network The system board provides an RJ-45 port for connection to 100Base-TX Fast Ethernet or 10Base-T Ethernet Network with a single connection over unshielded twisted-pair (UTP). The adapter automatically operates at 10Mbps or 100Mbps when the appropriate 10/100Base hub is connected. To connect the adapter to 100Base-TX Fast Ethernet Network, you need a twisted-pair Category 5 cable with RJ-45 modular jacks at both ends.
37 The ENDAT-7100M System Board Automatic Selection of the Media Type While the driver installs, it automatically detects the media type based on the type of cable connected. Once you change the cable type, you must reinstall the driver to execute auto-detect again. If the driver cannot detect which cable is connected or whether a cable is connected, look at cabling network driver (Ex. Modify net.cfg file parameters—force line speed=10 or 100).
38 User Manual Appendix A: FLASH Memory Utility Using this utility to update the system BIOS from a disk file to the on board Flash memory. Be aware the improper change of the system BIOS will cause the system to malfunction. Using utility as follows: 1. Insert the FLASH memory utility distribution floppy diskette in drive A: 2. At the DOS prompt, type A:>AWDFLASH and press AwardBIOS FLASH Utility V8.36E C>Phoenix Technologies Ltd.
39 The ENDAT-7100M System Board Appendix B: LCD Pin Assignment LVDS1: Dual Channel LVDS (1.25mm) Pin No. Signal Pin No. Signal 1 VBL (+12V) 2 VBL (+12V) 3 GND 4 GND 5 DISP.
User Manual 40 Appendix C: DIMM COMPATIBILITY In order to clear the memory recognize half of size to VIA CN700/CX700 platform, the following information is the description of chipset structure respect to memory’s design affect to system board.
41 The ENDAT-7100M System Board Appendix D: Limited Warranty Standard two years limited warranty on all our ENDAT series all-in-one motherboards and embedded boards. Products that become defective during the warranty period shall be repaired, or subject to manufacturer’s option, replaced. The limited warranty applies to normal proper usage of the hardware and does not cover products that have been modified or subjected to unusual electrical or physical stress.
42 User Manual RMA SERVICE REQUEST FORM When requesting RMA service, please fill out this “RMA Service Request Form”. This form needs to be shipped with your returns. Service cannot begin until we have this information. RMA NO.: Company: Person to Contact: Phone No: Purchase Date : Fax No. : Applied Date : Return Shipping Address: Model No. Serial No.
43 The ENDAT-7100M System Board Issue Code of defect. 01 Second Times R.M.A.
