User’s Manual VB6002 Version 1.
Copyright Copyright © 2006 VIA Technologies Incorporated. All rights reserved. No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise without the prior written permission of VIA Technologies, Incorporated. Trademarks All trademarks are the property of their respective holders. PS/2 is a registered trademark of IBM Corporation.
FCC-B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Safety Instructions 1. Always read the safety instructions carefully. 2. Keep this User's Manual for future reference. 3. Keep this equipment away from humidity. 4. Lay this equipment on a reliable flat surface before setting it up. 5. The openings on the enclosure are for air convection hence protects the equipment from 6. Make sure the voltage of the power source and adjust properly 110/220V before overheating. DO NOT COVER THE OPENINGS. connecting the equipment to the power inlet. 7.
B OX C ONTENTS One One One One One VIA Mini-ITX mainboard Quick Installation Guide ATA-133/100 IDE ribbon cable driver and utilities CD IO bracket i
T ABLE OF C ONTENTS Box Contents ......................................................................... i Table of Contents ..................................................................ii Chapter 1 ............................................................................ 1 Specifications .................................................................... 1 Mainboard Specifications ..................................................... 2 Mainboard Layout.........................................
CPU & PCI Bus Control ....................................................... 47 Integrated Peripherals ....................................................... 48 Super IO Device ................................................................ 51 Power Management Setup .................................................. 53 Peripheral Activities ........................................................... 55 IRQs Activities ..................................................................
This page is left intentionally blank.
CHAPTER 1 Specifications The ultra-compact and highly integrated VIA VB6002 uses the Mini-ITX mainboard form-factor developed by VIA Technologies, Inc. as part of the company’s open industry-wide total connectivity initiative. The mainboard enables the creation of an exciting new generation of small, ergonomic, innovative and affordable embedded systems. Through a high level of integration, the Mini-ITX occupy 66% of the size of FlexATX mainboard form factor.
Chapter 1 M AINBOARD S PECIFICATIONS CPU • Support Intel Pentium-M / Celeron-M Processor with MicroFCPGA package (socket 479) Chipset • VIA VN800 North Bridge • VIA VT8237R-series South Bridge Graphics • Integrated UniChrome™ Pro AGP with MPEG-2 Acceleration Audio • VIA VT1618 8-channel AC'97 Codec Memory • 1 x DDR2 533/400 DIMM slot (up to 1 GB) Expansion Slot • 1 x PCI slot • 2 x UltraDMA 133/100 connectors IDE LAN • VIA VT6103L 100/10 Base-TX Ethernet PHY • VIA VT6107 10/100 Mbps Fas
Specifications Onboard I/O Connectors • 1 x ATX power connector • 1 x Buzzer • 1 x Digital I/O pin header • 2 x Fan connectors (CPU Fan and System Fan) • 1 x Front Panel audio pin header (Mic-in and Line-out) • 1 x Front-Panel pin header • 1 x FS1 pin header for CPU front side bus speed selection • 1 x J2 pin header for VCCA selection • 1 x KBMS pin header (KB/MS or CIR) • 1 x LPC pin header • 1 x LPT pin header • 1 x LVDS/TTL/DVI (an add-on card is required) • 1 x P4_1 pin header
Chapter 1 M AINBOARD L AYOUT 4
Specifications B ACK P ANEL L AYOUT 5
Chapter 1 B ACK P ANEL P ORTS Port Description Audio Jacks COM1 PS/2 Mouse PS/2 Keyboard RJ45 USB VGA 3 Audio ports (line-out, line-in and mic-in) Serial port 1 PS/2 mouse port PS/2 keyboard port RJ45 ports USB 2.
Specifications O NBOARD C ONNECTORS Connector Description ATXPWR COM 2 CPUFAN F_AUDIO F_PANEL IDE 1-2 KBMS LPC LPT LVDS/TTL/DVI SATA 1-2 SIR SPDIF 1 SMBus SYSFAN USB 3-4 Power cable connector COM port 2 connector CPU fan connector Front Audio connector Front panel connector IDE drive connectors Keyboard and Mouse connector LPC connector LPT port connector LVDS/TTL/DVI connector Serial ATA 1 and 2 connectors Fast Infrared Radiation connector SPDIF Out connector SMBus connector System fan connector Univer
CHAPTER 2 Installation This chapter provides you with information about hardware installation procedures. It is recommended to use a grounded wrist strap before handling computer components. Electrostatic discharge (ESD) can damage some components.
Installation CPU The VIA VB6002 Mini-ITX mainboard can support Intel Pentium-M or Celeron-M Processors. These processors DO require a heatsink with fan to provide sufficient cooling.
Chapter 2 CPU Fan and System Fan: CPUFAN1 and SYSFAN1 The CPUFAN1 (CPU fan) and SYSFAN1 (system fan) run on +12V and maintain system cooling. When connecting the wire to the connectors, always be aware that the red wire is the Positive and should be connected to the +12V. The black wire is Ground and should always be connected to GND. FAN_MCM is a switch that is used by high-quality fans to monitor the system temperature and will automatically adjust according to the environment.
Installation MEMORY MODULE INSTALLATION The VIA VB6002 Mini-ITX mainboard provides one 240-pin DIMM slot for DDR2 533/400 SDRAM memory modules and supports the memory size up to 1GB. DIMM DDR2 SDRAM Module Installation Procedures • Locate the DIMM slot in the motherboard. • Unlock a DIMM slot by pressing the retaining clips outward. • Align a DIMM on the socket such that the notch on the DIMM matches the break on the slot.
Chapter 2 CONNECTING THE POWER SUPPLY The VIA VB6002 Mini-ITX mainboard supports a conventional ATX power supply for the power system. Before inserting the power supply connector, always make sure that all components are installed correctly to ensure that no damage will be caused. ATX 20-Pin Power Connector To connect the ATX power supply, make sure the power plug is inserted in the proper orientation and the pins are aligned. Then push down the plug firmly into the connector.
Installation BACK PANEL PORTS The back panel has the following ports: Keyboard and Mouse The green 6-pin connector is for a PS/2 mouse. The purple connector is for a PS/2 keyboard. Serial port: COM 1 The green 9-pin COM 1 port is for pointing devices or other serial devices. VGA Out The blue 15-pin female VGA connector can be used to connect to any analog VGA monitor.
Chapter 2 RJ45 10/100 LAN and USB Ports The mainboard provides two standard RJ-45 and four USB 2.0 ports. These ports allow connection to a Local Area Network (LAN) through a network hub and USB 2.0 devices.
Installation Audio Ports The Line-Out jack is for connecting to external speakers or headphones. The Line-In jack is for connecting to an external audio device such as a CD player, tape player, etc. The Mic jack is for connecting to a microphone. Note: The audio ports can be switched to Smart 5.1 6-channel audio output. You can enable the function by clicking the “Vinyl Audio” icon on your desktop after installing the audio driver.
Chapter 2 CONNECTORS Hard Disk Connectors: IDE1 & IDE2 The mainboard has a 32-bit Enhanced IDE and Ultra DMA 133/100 controller that provides PIO mode 0~4, Bus Master, and Ultra DMA 133/100 functions. You can connect up to four hard disk drives, CD-ROM and other devices. The primary hard drive should always be connected to IDE1 as the master drive. Both IDE drives can connect to a master and a slave drive.
Installation Case Connector: F_PANEL1 The F_PANEL1 pin header allows you to connect the power switch, reset switch, power LED, sleep LED, HDD LED and the case speaker. Pin Signal Pin Signal F_PANEL1 1 3 5 7 9 11 13 15 +5V +5V -PLED_2 +5V NC NC SPEAK Key 2 4 6 8 10 12 14 16 +5V HD_LED PW_BN GND RST_SW GND +5V -SLEEP_LED 1 2 15 16 Power Switch (PW_BN) Connect to a 2-pin power button switch. Pressing this button will turn the system power on or off.
Chapter 2 Serial ATA Connectors: SATA1 and SATA2 SATA1-2 These next generation connectors support the thin Serial ATA cables for primary internal storage devices. The current Serial ATA interface allows up to 150MB/s data transfer rate, faster than the standard parallel ATA with 133 MB/s (Ultra DMA). Digital Audio Connector: SPDIF1 This connector is for connecting the Sony Philips Digital Interface (S/PDIF) bracket.
Installation USB Pin Connector: USB_3-4 The mainboard provides 1 front USB pin header, allowing up to 2 additional USB2.0 ports up to maximum throughput of 480 Mbps. Connect each 2-port USB cable into this pin header. This port can be used to connect high-speed USB interface peripherals such as USB HDD, digital cameras, MP3 players, printers, modem and the like.
Chapter 2 Serial Port Connector: COM2 COM2 pin header can be used to attach additional port for serial mouse or another serial device. Pin Signal Pin Signal 1 3 5 7 9 RIN12 DOUT22 GND DOUT12 -XRI2 2 4 6 8 10 RIN32 DOUT32 RIN22 RIN42 Key COM2 1 2 9 10 Front Panel Audio Connector: F_AUDIO1 This is an interface for the VIA front panel audio cable that allow convenient connection and control of audio devices.
Installation LVDS/TTL/DVI Connector: J1 This connector works as the interface to multi display devices. An additional daughter card is required for a certain display support. Daughter cards for LVDS and DVI are currently available respectively. Pin Signal Pin Signal 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 DVID0 DVID2 DVID4 DVID6 DVID8 DVID10 DVIDE DVIVS DVIHS GND +12V +12V GND +3.
Chapter 2 Note: ENPVDD: Enable Panel VDD power ENPVEE: Enable Panel VEE power GFPD: Graphic Flat Panel Device signals KBMS Connector: KBMS1 The mainboard provides a PS2 pin header to attach a PS2 keyboard and mouse. Pin Signal Pin Signal 1 3 5 7 9 +5VDUAL KB_CLK EKBCLK MS_CLK EMSCLK 2 4 6 8 10 GND KB_DATA EKBDATA MS_DATA EMSDATA KBMS1 2 10 1 9 Note: When the pin header is not in use, please short pin 3&5, pin 4&6, pin 7&9 and pin 8&10.
Installation LPT Connector: LPT1 The mainboard provides a 26-pin connector to be able to connect a 25-pin female external connector for LPT (parallel port). A parallel port is a standard printer port that supports Enhanced Parallel Port (EPP) and Extended Capabilities Parallel Port (ECP) modes.
Chapter 2 JUMPERS The mainboard provides jumpers for setting some mainboard functions. This section will explain how to change the settings of the mainboard functions using the jumpers. Clear CMOS: CLEAR_CMOS1 The onboard CMOS RAM stores system configuration data and has an onboard battery power supply. To reset the CMOS settings, set the jumper on pins 2 and 3 while the system is off. Return the jumper to pins 1 and 2 afterwards. Setting the jumper while the system is on will damage the mainboard.
Installation Intel Pentium® M or Celeron® M Select: J2, P4_1-2 These jumpers are for selecting between Intel Pentium® M or Celeron® M processors. Shorting pin 1 & 2 of J2 will select 1.8V VCCA power; shoring pin 2 & 3 will select 1.5V. For CPU type, shorting P4_1 and J2 opening P4_2 will select Intel Pentium-M / Celeron-M. J2 Setting 1 2 3 1.5V 1.8V OFF ON ON ON ON OFF Setting P4_1 P4_2 Intel Pentium-M / Celeron-M ON OFF 1.8V: 3 2 1 1.
Chapter 2 SLOTS Peripheral Component Interconnect: PCI1 The PCI slot allows you to insert PCI expansion card. When adding or removing expansion card, unplug first the power supply. Read the documentation for the expansion card if any changes to the system are necessary. PCI PCI Interrupt Request Routing The IRQ (interrupt request line) are hardware lines over which devices can send interrupt signals to the microprocessor.
CHAPTER 3 BIOS Setup This chapter gives a detailed explanation of the BIOS setup functions.
Chapter 3 ENTERING SETUP Power on the computer and press during the beginning of the boot sequence to enter the BIOS setup menu. If you missed the BIOS setup entry point, you may restart the system and try again.
BIOS Setup CONTROL KEYS Keys Description Up Arrow Down Arrow Left Arrow Right Arrow Enter Escape Move to the previous item Move to the next item Move to the item in the left side Move to the item in the right side Select the item Jumps to the Exit menu or returns to the main menu from a submenu Increase the numeric value or make changes Decrease the numeric value or make changes General help, only for Status Page Setup Menu and Option Page Setup Menu Restore the previous CMOS value from CMOS, only for O
Chapter 3 NAVIGATING THE BIOS MENUS The main menu displays all the BIOS setup categories. Use the control keys Up/Down arrow keys to select any item/sub-menu. Description of the selected/highlighted category is displayed at the bottom of the screen. An arrow symbol next to a field indicates that a sub-menu is available (see figure below). Press to display the sub-menu. menu, press .
BIOS Setup GETTING HELP The BIOS setup program provides a “General Help” screen. You can display this screen from any menu/sub-menu by pressing . The help screen displays the keys for using and navigating the BIOS setup. Press to exit the help screen.
Chapter 3 MAIN MENU Phoenix - AwardBIOS CMOS Setup Utility Standard CMOS Features Frequency / Voltage Control Advanced BIOS Features Load Fail-Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Management Setup Set User Password PnP / PCI Configurations Save & Exit Setup PC Health Status Exit Without Saving Esc : Quit F9 : Menu in BIOS : Select Item F10 : Save & Exit Setup Time, Date, Hard Disk Type...
BIOS Setup Frequency/Voltage Control Use this menu to set the system frequency and voltage control. Load Fail-Safe Defaults Use this menu option to load the BIOS default settings for minimal and stable system operations. Load Optimized Defaults Use this menu option to load BIOS default settings for optimal and high performance system operations. Set Supervisor Password Use this menu option to set the BIOS supervisor password. Set User Password Use this menu option to set the BIOS user password.
Chapter 3 STANDARD CMOS FEATURES Phoenix - AwardBIOS CMOS Setup Utility Standard CMOS Features Date (mm:dd:yy) Time (hh:mm:ss) Tue, Apr 21 2004 20 : 20 : 20 IDE Channel 0 Master IDE Channel 0 Slave IDE Channel 1 Master IDE Channel 1 Slave Item Help Menu Level Change the day, month, year and century Halt On [All , But Keyboard] Base Memory Extended Memory Total Memory 640K 195584K 196608K : Move Enter: Select F5: Previous Values +/-/PU/PD: Value F10: Save F6: Fail-Safe Defaults ESC: Exit F1: Gener
BIOS Setup IDE DRIVES Phoenix - AwardBIOS CMOS Setup Utility IDE Channel 0 Master IDE HDD Auto-Detection [Press Enter] IDE Channel 0 Master Access Mode [Auto] [Auto] Capacity 0 MB Cylinder Head Precomp Landing Zone Sector 0 0 0 0 0 PIO Mode Ultra DMA Mode [Auto] [Auto] : Move Enter: Select F5: Previous Values Item Help Menu Level To auto-detect the HDD's size, head...
Chapter 3 ADVANCED BIOS FEATURES Phoenix - AwardBIOS CMOS Setup Utility Advanced BIOS Features CPU Feature Hard Disk Boot Priority Virus Warning CPU L1 & L2 Cache Quick Power On Self Test First Boot Device Second Boot Device Third Boot Device Boot Other Device Boot Up NumLock Status Typematic Rate Setting Typematic Rate (Chars/Sec) Typematic Delay (Msec) Security Option APIC Mode MPS Version Control For OS Display Full Screen Logo Display Small Logo : Move Enter: Select F5: Previous Values [Press Enter]
BIOS Setup First/Second/Third Boot Device Set the boot device sequence as BIOS attempts to load the disk operating system.
Chapter 3 Typematic Rate (Chars/Sec) This item sets the rate (characters/second) at which the system retrieves a signal from a depressed key. Settings: [6, 8, 10, 12, 15, 20, 24, 30] Typematic Delay (Msec) This item sets the delay between when the key was first pressed and when the system begins to repeat the signal from the depressed key. Settings: [250, 500, 750, 1000] Security Option Selects whether the password is required every time the System boots, or only when you enter Setup.
BIOS Setup CPU FEATURE This feature IS NOT SUPPORTED for Intel Pentium® M or Celeron® M processors. Phoenix - AwardBIOS CMOS Setup Utility CPU Feature Thermal Management TM2 Bus Ratio TM2 Bus VID Execute Disable Bit C7-M CMPXCHG8 C7-M NoExecute (NX) C7-M TM1/TM2 Working Temp C7-M TM Overstress Temp oC ODCM ACPI C4 Function : Move Enter: Select F5: Previous Values [Thermal Monitor 1] [ 0 X] [0.
Chapter 3 TM2 Bus VID This item sets the voltage of the throttled performance that will be initiated when the on die sensor goes from not hot to hot. Settings: [0.700V, 0.716V, 0.732V, 0.748V, 0.764V, 0.780V, 0.796V, 0.812V, 0.828V, 0.844V, 0.860V, 0.876V, 0.892V, 0.908V, 0.924V, 0.940V, 0.956V, 0.972V, 0.988V, 1.004V, 1.020V, 1.036V, 1.052V, 1.068V, 1.084V, 1.100V, 1.116V, 1.132V, 1.148V, 1.164V, 1.180V, 1.196V, 1.212V, 1.228V, 1.244V, 1.260V, 1.276V, 1.292V, 1.308V, 1.324V, 1.340V, 1.356V, 1.372V, 1.
BIOS Setup C7-M TM1/TM2 Working Temp ºC This item sets the high threshold and the low threshold (lo = high-5ºC). Key in a DEC number. Settings: [Min = 0, Max = 255] C7-M TM Overstress Temp ºC Key in a DEC number. Settings: [Min = 0, Max = 255] ODCM Enables the ODCM (On Demand Clock Modulation) functionality. Settings: [12.5%, 25.0%, 37.5%, 50.0%, 62.5%, 75.0%, 87.5%, Disabled] ACPI C4 Function Enables the ACPI (Advanced Configuration and Power Management Interface) C4 functionality.
Chapter 3 HARD DISK BOOT PRIORITY Phoenix - AwardBIOS CMOS Setup Utility Hard Disk Boot Priority 1. 2. 3. 4. 5. 6. 7. 8. Item Help Pri. Master : Pri. Slave : Sec. Master : Sec. Slave : USBHDD0 : USBHDD1 : USBHDD2 : Bootable Add-In Cards Menu Level Use < > or < > to select a device, then press < + > to move it up, or < - > to move it down the list. Press to exit this menu.
BIOS Setup ADVANCED CHIPSET FEATURES Phoenix - AwardBIOS CMOS Setup Utility Advanced Chipset Features Display Card Priority AGP & P2P Bridge Control CPU & PCI Bus Control AGP Driving Control AGP Driving Value Select Display Device Panel Type : Move Enter: Select F5: Previous Values [PCI Slot] [Press Enter] [Press Enter] [Auto] DA [CRT] [07] +/-/PU/PD: Value F10: Save F6: Fail-Safe Defaults Item Help Menu Level If there are display cards on both AGP and PCI slots, configure this item for BIOS to select
Chapter 3 Select Display Device This setting refers to the type of display being used with the system. Settings: [CRT, LCD, CRT+LCD, DVI, CRT+DVI] Panel Type This setting refers to the native resolution of the display being used with the system. Key in a HEX number.
BIOS Setup AGP & P2P BRIDGE CONTROL Phoenix - AwardBIOS CMOS Setup Utility AGP & P2P Bridge Control AGP Aperture Size AGP 2.0 Mode AGP Fast Write AGP 3.
Chapter 3 AGP Fast Write This item is used to enable or disable the caching of display data for the video memory of the processor. Settings: [Enabled, Disabled] AGP 3.
BIOS Setup CPU & PCI BUS CONTROL Phoenix - AwardBIOS CMOS Setup Utility CPU & PCI Bus Control VLink mode selection VLink 8X Support DRDY_Timing : Move Enter: Select F5: Previous Values [By Auto] [Enabled] [Default] +/-/PU/PD: Value F10: Save F6: Fail-Safe Defaults Item Help Menu Level ESC: Exit F1: General Help F7: Optimized Defaults V-Link mode selection This menu item controls the data transfer speed between the north and south bridge.
Chapter 3 INTEGRATED PERIPHERALS Phoenix - AwardBIOS CMOS Setup Utility Integrated Peripherals SuperIO Device [Press Enter] Onboard IDE Channel 1 Onboard IDE Channel 2 IDE Prefetch Mode IDE HDD Block Mode OnChip SATA SATA Mode [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] [RAID] AC97 Audio VIA OnChip LAN OnChip LAN Boot ROM [Auto] [Enabled] [Disabled] Onboard LAN Boot ROM [Disabled] OnChip USB Controller OnChip EHCI Controller USB Emulation Watch Dog Timer Select [All Enabled] [Enabled] [On] [
BIOS Setup OnChip SATA Settings: [Enabled, Disabled] SATA Mode Serial ATA is the latest generation of the ATA interface. Serial ATA hard drives deliver transfer speeds of up to 150MB/sec. Setting Description IDE RAID Supports two SATA plus two PATA hard disk drives Only SATA supports RAID AC’97 Audio Auto allows the mainboard to detect whether an audio device is used. If the device is detected, the onboard VIA AC'97 (Audio Codec'97) controller will be enabled; otherwise, it is disabled.
Chapter 3 OnChip USB Controller Settings: [All Disabled, All Enabled, 1&2 USB Port, 2&3 USB Port, 1&3 USB Port, 1 USB Port, 2 USB Port, 3 USB Port] OnChip EHCI Controller Settings: [Enabled, Disabled] USB Emulation Set this field to choose the USB emulation. When set to “OFF “, do not support any USB device on DOS. When set to “KB/MS”, support USB legacy keyboard and mouse, no support USB storage. And set to ”ON”, support USB legacy keyboard, mouse and storage.
BIOS Setup SUPER IO DEVICE Phoenix - AwardBIOS CMOS Setup Utility SuperIO Device Onboard Serial Port 1 Onboard Serial Port 2 UART Mode Select RxD, TxD Active IR Transmission Delay UR2 Duplex Mode Use IR Pins Onboard Parallel Port Parallel Port Mode EPP Mode Select ECP Mode Use DMA : Move Enter: Select F5: Previous Values [3F8/IRQ4] [2F8/IRQ3] [Normal] [Hi,Lo] [Enabled] [Half] [IR-Rx2Tx2] [378/IRQ7] [SPP] [EPP1.
Chapter 3 UR2 Duplex Mode Settings: [Full, Half] Use IR Pins Settings: [RxD2.TxD2, IR-Rx2Tx2] Onboard Parallel Port This specifies the I/O port address and IRQ of the onboard parallel port. Settings: [Disabled, 378/IRQ7, 278/IRQ5, 3BC/IRQ7] Parallel Port Mode Set the parallel port mode. To operate the onboard parallel port as Standard Parallel Port, choose SPP. To operate the onboard parallel port in the EPP mode, choose EPP. By choosing ECP, the onboard parallel port will operate in ECP mode.
BIOS Setup POWER MANAGEMENT SETUP Phoenix - AwardBIOS CMOS Setup Utility Power Management Setup ACPI Suspend Type HDD Power Down Power Management Timer Video Off Option [S1(POS)] [Disabled] [Disabled] [Suspend -> Off] Power Off by PWRBTN Run VGABIOS if S3 Resume AC Loss Auto Restart Peripherals Activities IRQs Activities [Instant-Off] [Auto] [On] [Press Enter] [Press Enter] Item Help Menu Level This item allows you to select how the BIOS put system into power saving mode.
Chapter 3 Video Off Option Select whether or not to turn off the screen when system enters power saving mode, ACPI OS such as Windows XP will override this option. Setting Description Always On Screen is always on even when system enters power saving mode Screen is turned off when system enters power saving mode Suspend -> Off Power Off by PWRBTN This field configures the power button on the chassis.
BIOS Setup PERIPHERAL ACTIVITIES Phoenix - AwardBIOS CMOS Setup Utility Peripherals Activities PS2KB Wakeup Select PS2MS Wakeup from S3/S4/S5 PS2KB Wakeup from S3/S4/S5 USB Resume from S3 VGA Event LPT & COM Event HDD Event PCI Master Event PowerOn by PCI Card Modem Ring Resume RTC Alarm Resume Date (of Month) Resume Time (hh:mm:ss) : Move Enter: Select F5: Previous Values [Hot Key] [Disabled] [Disabled] [Disabled] [OFF] [COM] [ON] [OFF] [Disabled] [Disabled] [Disabled] 0 0: 0: 0 Item Help Menu Level Wh
Chapter 3 PS2MS Wakeup from S3/S4/S5 Enables any mouse activity to restore the system from the power saving mode to an active state. Settings: [Disabled, Enabled] USB Resume from S3 Enables activity detected from USB devices to restore the system from a suspended state to an active state. Settings: [Disabled, Enabled] VGA Event Enables the power management unit to monitor VGA activities.
BIOS Setup PowerOn by PCI Card Enables activity detected from any PCI card to power up the system or resume from a suspended state. Such PCI cards include LAN, onboard USB ports, etc. Settings: [Disabled, Enabled] Modem Ring Resume Enables any Ring-In signals from the modem to restore the system from a suspended state to an active state. Settings: [Disabled, Enabled] RTC Alarm Resume Sets a scheduled time and/or date to automatically power on the system.
Chapter 3 IRQS ACTIVITIES Phoenix - AwardBIOS CMOS Setup Utility IRQs Activities Primary INTR IRQ3 (COM 2) IRQ4 (COM 1) IRQ5 (Reserved) IRQ6 (Floppy Disk) IRQ7 (LPT 1) IRQ8 (RTC Alarm) IRQ9 (IRQ2 Redir) IRQ10 (Reserved) IRQ11 (Reserved) IRQ12 (PS/2 Mouse) IRQ13 (Coprocessor) IRQ14 (Hard Disk) IRQ15 (Reserved) : Move Enter: Select F5: Previous Values [ON] [Enabled] [Enabled] [Disabled] [Disabled] [Enabled] [Disabled] [Disabled] [Disabled] [Disabled] [Enabled] [Enabled] [Enabled] [Disabled] +/-/PU/PD: Val
BIOS Setup PNP/PCI CONFIGURATIONS Phoenix - AwardBIOS CMOS Setup Utility PnP / PCI Configurations PNP OS Installed Reset Configuration Data [No] [Disabled] Resources Controlled By IRQ Resources Assign IRQ For VGA Assign IRQ For USB [Auto(ESCD)] Press Enter [Enabled] [Enabled] : Move Enter: Select F5: Previous Values NOTE: +/-/PU/PD: Value F10: Save F6: Fail-Safe Defaults Item Help Menu Level Select Yes if you are using a Plug and Play capable operating system.
Chapter 3 Resource Controlled By Enables the BIOS to automatically configure all the Plug-and-Play compatible devices. Setting Description Auto(ESCD) BIOS will automatically assign IRQ, DMA and memory base address fields Unlocks “IRQ Resources” for manual configuration Manual Assign IRQ For VGA/USB Assign IRQ for VGA and USB devices.
BIOS Setup IRQ RESOURCES Phoenix - AwardBIOS CMOS Setup Utility IRQ Resources IRQ-3 assigned to IRQ-4 assigned to IRQ-5 assigned to IRQ-7 assigned to IRQ-9 assigned to IRQ-10 assigned to IRQ-11 assigned to IRQ-12 assigned to IRQ-14 assigned to IRQ-15 assigned to [PCI Device] [PCI Device] [PCI Device] [PCI Device] [PCI Device] [PCI Device] [PCI Device] [PCI Device] [PCI Device] [PCI Device] : Move Enter: Select F5: Previous Values +/-/PU/PD: Value F10: Save F6: Fail-Safe Defaults Item Help Menu Level Le
Chapter 3 PC HEALTH STATUS Phoenix - AwardBIOS CMOS Setup Utility PC Health Status SYSTEM Temp. CPU Temp. SYSTEM FAN Speed CPU FAN Speed Vcore 3.
BIOS Setup FREQUENCY / VOLTAGE CONTROL Phoenix - AwardBIOS CMOS Setup Utility Frequency / Voltage Control DRAM Clock [By SPD] DRAM Timing [Auto By SPD] SDRAM CAS Latency [DDR/DDR2] 2.
Chapter 3 Bank Interleave This item is for setting the interleave mode of the SDRAM interface. Interleaving allows banks of SDRAM to alternate their refresh and access cycles. One bank will undergo its refresh cycle while another is being accessed. This improves performance of the SDRAM by masking the refresh time of each bank. This field is only available when “DRAM Timing” is set to “Manual”.
BIOS Setup REF to ACT / REF (Trfc) This field is only available when “DRAM Timing” is set to “Manual”. Settings: [08T, 09~71T] ACT(0) to ACT(1) (TRRD) This field is only available when “DRAM Timing” is set to “Manual”. Settings: [2T, 3T, 4T, 5T] Read to Precharge (Trptp) Settings: [2T, 3T] Write to Read CMD (Twtr) Settings: [1T/2T, 2T/3T] Write Recovery Time (Twr) Settings: [2T, 3T, 4T, 5T] DRAM Command Rate This field is for setting how fast the memory controller sends out commands.
Chapter 3 Auto Detect PCI Clk Settings: [Disabled, Enabled] CPU Clock Key in a DEC number. Settings: [Min = 100, Max = 333] CPU Clock Ratio Key in a DEC number. Settings: [Min = 8, Max = 50] Spread Spectrum When the mainboard's clock generator pulses, the extreme values (spikes) of the pulses create EMI (Electromagnetic Interference). The Spread Spectrum function reduces the EMI generated by modulating the pulses so that the spikes of the pulses are reduced to flatter curves. Settings: [Disabled, 0.
BIOS Setup LOAD FAIL-SAFE DEFAULTS Phoenix - AwardBIOS CMOS Setup Utility Standard CMOS Features Frequency / Voltage Control Advanced BIOS Features Load Fail-Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Management Setup PnP / PCI Configurations Set User Password &N Exit Setup Load Fail-Safe DefaultsSave (Y/N)? PC Health Status Esc : Quit Exit Without Saving F9 : Menu in BIOS : Select Item F10 : Save & Exit Setup Load Fai
Chapter 3 LOAD OPTIMIZED DEFAULTS Phoenix - AwardBIOS CMOS Setup Utility Standard CMOS Features Frequency / Voltage Control Advanced BIOS Features Load Fail-Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Management Setup PnP / PCI Configurations Set User Password &NExit Setup Load Optimized DefaultsSave (Y/N)? PC Health Status Esc : Quit Exit Without Saving F9 : Menu in BIOS : Select Item F10 : Save & Exit Setup Load Optim
BIOS Setup SET SUPERVISOR / USER PASSWORD Phoenix - AwardBIOS CMOS Setup Utility Standard CMOS Features Frequency / Voltage Control Advanced BIOS Features Load Fail-Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Management Setup Set User Password PnP / PCI Configurations Enter Password: Save & Exit Setup PC Health Status Exit Without Saving Esc : Quit F9 : Menu in BIOS : Select Item F10 : Save & Exit Setup Change / Set /
Chapter 3 Additionally, when a password is enabled, the BIOS can be set to request the password each time the system is booted. This would prevent unauthorized use of the system. See “Security Option” in the “Advanced BIOS Features” section for more details.
BIOS Setup SAVE & EXIT SETUP Phoenix - AwardBIOS CMOS Setup Utility Standard CMOS Features Frequency / Voltage Control Advanced BIOS Features Load Fail-Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Management Setup PnP / PCI Configurations Set User Password &NExit Setup SAVE to CMOS & EXITSave (Y/N)? Exit Without Saving PC Health Status Esc : Quit F9 : Menu in BIOS : Select Item F10 : Save & Exit Setup Save Data to CMOS E
Chapter 3 EXIT WITHOUT SAVING Phoenix - AwardBIOS CMOS Setup Utility Standard CMOS Features Frequency / Voltage Control Advanced BIOS Features Load Fail-Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Management Setup PnP / PCI Configurations Set User Password Save & N Exit Setup Quit Without Saving (Y/N)? Exit Without Saving PC Health Status Esc : Quit F9 : Menu in BIOS : Select Item F10 : Save & Exit Setup Abandon all Data
CHAPTER 4 Driver Installation This chapter gives you brief descriptions of each mainboard driver and application. You must install the VIA chipset drivers first before installing other drivers such as audio or VGA drivers. The applications will only function correctly if the necessary drivers are already installed.
Chapter 4 DRIVER UTILITIES Getting Started The mainboard includes a Driver Utilities CD that contains the driver utilities and software for enhancing the performance of the mainboard. If the CD is missing from the retail box, please contact the local dealer for the CD. Note: The driver utilities and software are updated from time to time. The latest updated versions are available at http://www.viaembedded.com.
Driver Installation Running the Driver Utilities CD To start using the CD, insert the CD into the CD-ROM or DVD-ROM drive. The CD should run automatically after closing the CD-ROM or DVD-ROM drive. The driver utilities and software menu screen should then appear on the screen. If the CD does not run automatically, click on the “Start” button and select “Run…” Then type: "D:\Setup.exe". NOTE: D: might not be the drive letter of the CD-ROM/DVD-ROM in your system.
Chapter 4 CD CONTENT VIA 4in1 Drivers: Contains VIA ATAPI Vendor Support Driver (enables the performance enhancing bus mastering functions on ATA-capable Hard Disk Drives and ensures IDE device compatibility), AGP VxD Driver (provides service routines to your VGA driver and interface directly to hardware, providing fast graphical access), IRQ Routing Miniport Driver (sets the system's PCI IRQ routing sequence) and VIA INF Driver (enables the VIA Power Management function).
